Table of Contents
Advertisement
STORM
INSTRUCTIONS FOR
2000W 230V 230mm
Angle Grinder
Stock No.83594
Part No.PT2023SF
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY TO ENSURE THE SAFE AND
EFFECTIVE USE OF THIS PRODUCT.
GENERAL INFORMATION
These instructions accompanying the product are the original instructions. This document is part of the product, keep it
for the life of the product passing it on to any subsequent holder of the product. Read all these instructions before
assembling, operating or maintaining this product.
This manual has been compiled by Draper Tools describing the purpose for which the product has been designed, and
contains all the necessary information to ensure its correct and safe use. By following all the general safety instructions
contained in this manual, it will ensure both product and operator safety, together with longer life of the product itself.
AlI photographs and drawings in this manual are supplied by Draper Tools to help illustrate the operation of the product.
Whilst every effort has been made to ensure the accuracy of information contained in this manual, the Draper Tools
policy of continuous improvement determines the right to make modifications without prior warning.
Advertisement
Table of Contents
Related Manuals for Draper PT2023SF
Summary of Contents for Draper PT2023SF
-
Page 1: General Information
AlI photographs and drawings in this manual are supplied by Draper Tools to help illustrate the operation of the product. -
Page 2: Title Page
Commercial copying, redistribution, hiring or lending is prohibited. No part of this publication may be stored in a retrieval system or transmitted in any other form or means without written permission from Draper Tools Limited. In all cases this copyright notice must remain intact. -
Page 3: Table Of Contents
CONTENTS CONTENTS PAGE CONTENT PAGE TITLE PAGE INTRODUCTION ....................2 REVISION HISTORY....................2 UNDERSTANDING THIS MANUAL ...............2 COPYRIGHT NOTICE....................2 CONTENTS CONTENTS ......................3 GUARANTEE GUARANTEE ......................4 INTRODUCTION SCOPE ........................5 SPECIFICATION ......................5 HANDLING & STORAGE ..................5 HEALTH & SAFETY INFORMATION GENERAL SAFETY INSTRUCTIONS FOR POWER TOOL USE .........6 SPECIFIC SAFETY INSTRUCTIONS FOR GRINDER USE...........6 SAFETY RECOMMENDATIONS FOR THE CORRECT USE OF ABRASIVE PRODUCTS ......................8... -
Page 4: Guarantee 3.1 Guarantee
This guarantee applies in lieu of any other guarantee expressed or implied and variations of its terms are not authorised. Your Draper guarantee is not effective unless you can produce upon request a dated receipt or invoice to verify your proof of purchase within the guarantee period. -
Page 5: Introduction
This hand held power tool uses abrasive disks to grind metals or masonry. It is intended for domestic and light commercial use only. Any other application is considered misuse. 4.2 SPECIFICATION Stock no ........................... 83594 Part no ..........................PT2023SF Motor: Rated voltage ........................230V~ Rated frequency ........................50Hz Rated input ........................ -
Page 6: Health & Safety Information
HEALTH & SAFETY INFORMATION 5.1 GENERAL SAFETY INSTRUCTIONS FOR POWER TOOL USE When using any type of power tool there are steps that should be taken to make sure that you, as the user, remain safe. Common sense and a respect for the tool will help reduce the risk of injury. Read the instruction manual fully. - Page 7 HEALTH & SAFETY INFORMATION Ensure that mounted wheels and points are fitted in accordance with the manufacturer’s instructions; Ensure that blotters are used when they are provided with the bonded abrasive product and when they are required; Ensure that the abrasive product is correctly mounted and tightened before use and run the tool at no-load for 30 seconds in a safe position, stop immediately if there is considerable vibration or if other defects are detected.
-
Page 8: Safety Recommendations For The Correct Use Of Abrasive Products
HEALTH & SAFETY INFORMATION 10. Check damaged parts. Before further use of the tool, a guard or other part that is damaged should be carefully checked to determine that it will operate properly and perform its intended function. Check for alignment of moving parts, free running of moving parts, breakage of parts, mounting and any other conditions that may affect its operation. -
Page 9: Safety Recommendations For The Correct Use Of Superabrasives
HEALTH & SAFETY INFORMATION SAFETY RECOMMENDATIONS FOR THE CORRECT USE OF SUPERABRASIVES. General. Superabrasives are breakable and shall therefore be handled with utmost care! The use of damaged or improperly mounted or used superabrasives is dangerous and can cause serious injuries. b. -
Page 10: Connection To The Power Supply
HEALTH & SAFETY INFORMATION 5.5 CONNECTION TO THE POWER SUPPLY Make sure the power supply information on the machine’s rating plate are compatible with the power supply you intend to connect it to. This product comes supplied with a UK standard 3 pin plug fitted. It is designed for connection to a domestic power supply rated at 230V AC. -
Page 11: Technical Description
TECHNICAL DESCRIPTION 6.1 IDENTIFICATION Spindle lock button Handle rotation button Rear hand grip Plug & cable Auxiliary handle Grinding guard Locking flange Trigger switch... -
Page 12: Unpacking & Checking
Lay the contents out and check them against the parts shown below. If any part is damaged or missing; please contact the Draper Help Line (the telephone number appears on the Title page) and do not attempt to use the product. -
Page 13: Preparing The Grinder
PREPARING THE GRINDER 8.1 FITTING AUXILIARY HANDLES – FIG. 1 FIG. 1 NOTE: Remove the plug from the socket before carrying out adjustment, servicing or maintenance. For reasons of safety, when working with this type of electric power tool, the operator must always use the auxiliary handle Screw the handle clockwise, into one of the three threaded apertures best suited to the application and... -
Page 14: Fitting/Replacing Accessories (Not Supplied)
For cutting applications, and to comply to current legislation, it is necessary to replace the “grinding” guard supplied with this machine with a “cutting” guard. The appropriate “cutting” guard is available from Draper Tools and must be fitted for your safety. -
Page 15: Setting The Grinder
SETTING THE GRINDER FITTING GRINDING DISCS – FIGS. 5 – 7 FIG. 5 Press and hold the spindle lock button . Loosen the locking flange anti-clockwise using the pin spanner supplied. The spindle may rotate slightly before the spindle lock fully engages. Remove the locking flange only. -
Page 16: Grinding
NOTICE NOTICE Cutting operations should only be attempted with the “cutting” guard fitted to this grinder. Please contact Draper Tools for further information on how to purchase this optional accessory. This guard must be fitted for your safety. When performing cutting-off operations do not... -
Page 17: Optional Accessories
10. OPTIONAL ACCESSORIES 10.1 OPTIONAL ACCESSORIES See your Draper Stockist. -
Page 18: Troubleshooting
11. TROUBLESHOOTING 11.1 TROUBLESHOOTING WARNING: For your own safety, turn the switch off and remove the plug from the power supply socket. PROBLEM POSSIBLE CAUSE REQUIRED ACTION • Motor does not • Fuse. • 5 amp time delay fuse or start. -
Page 19: Maintenance
12. MAINTENANCE 12.1 MAINTENANCE & PARTS REPLACEMENT Regular inspection and cleaning reduces the necessity for maintenance operations and will keep your tool in good working condition. The motor must be correctly ventilated during tool operation. For this reason avoid blocking the air inlets. -
Page 20: Explanation Of Symbols
13. EXPLANATION OF SYMBOLS 13.1 EXPLANATION OF SYMBOLS Warning! Wear dust mask. Warning! Read the instruction manual Warning! Warning! Wear suitable eye/face Wear ear defenders. protection. WEEE Do not dispose of Waste Electrical & Electronic Equipment in with domestic rubbish Class II construction (Double insulated). -
Page 21: Disposal
14. DISPOSAL 14.1 DISPOSAL - At the end of the machine’s working life, or when it can no longer be repaired, ensure that it is disposed of according to national regulations. - Contact your local authority for details of collection schemes in your area. In all circumstances: •... - Page 22 NOTES...
- Page 23 NOTES...
- Page 24 - Sales Desk: (023) 8049 4333 - General Enquiries: (023) 8026 6355 - Service/Warranty Repair Agent For aftersales servicing or warranty repairs, please contact the Draper Tools Help Line for details of an agent in your local area. (Weight (gross…..6.6kg) YOUR DRAPER STOCKIST RDCH0816 drapertools.com...
Need help?
Do you have a question about the PT2023SF and is the answer not in the manual?
Questions and answers