Table of Contents
Advertisement
■
If the grass shears is installed with an adjustable handle,
make sure that the grass shears is turned off and the
blades are not moving before adjusting the handle.
■
Operate the product only in temperatures between 0°C
and 40°C.
■
Store the product in a location where the ambient
temperature is between 0°C and 40°C.
ADDITIONAL BATTERY SAFETY WARNINGS
■
To reduce the risk of fire, personal injury, and product
damage due to a short circuit, never immerse the
product, battery pack, or charger in fluid or allow fluid
to flow inside them. Corrosive or conductive fluids, such
as seawater, certain industrial chemicals, and bleach
or bleach-containing products, etc., can cause a short
circuit.
■
Charge the battery pack in a location where the ambient
temperature is between 10°C and 38°C.
■
Store the battery pack in a location where the ambient
temperature is between 0°C and 20°C.
■
Use the battery pack in a location where the ambient
temperature is between 0°C and 40°C.
TRANSPORTATION AND STORAGE
■
When transporting or storing the product, always fit the
product with the blade cover.
■
Clean the product thoroughly before storing. Store the
product in a dry, well-ventilated area that is inaccessible
to children. Keep the product away from corrosive
agents, such as garden chemicals and de-icing salts.
■
Store and charge the battery packs in a cool area.
Temperatures above or below normal room temperature
shorten the battery life.
■
Never store the battery packs in a discharged condition.
Wait for the battery pack to cool down and charge
immediately.
■
When transporting the product in a vehicle, secure it
against movement or falling to prevent injury to persons
or damage to the product.
TRANSPORTING LITHIUM BATTERIES
Transport the battery in accordance with local and national
provisions and regulations.
Follow all special requirements on packaging and labelling
when transporting batteries by a third party. Ensure that
no batteries can come in contact with other batteries
or conductive materials while in transport by protecting
exposed connectors with insulating, nonconductive caps or
tape. Do not transport batteries that are cracked or leaking.
Check with the forwarding company for further advice.
MAINTENANCE
■
Use only original manufacturer's replacement parts,
accessories, and attachments. Failure to do so can cause
possible injury, can contribute to poor performance, and
may void your warranty.
■
Servicing requires extreme care and knowledge
and should be performed only by a qualified service
technician. For service, bring the product to an
authorised service centre for repair.
■
Turn off the product and remove the battery pack before
conducting any maintenance or cleaning work.
4
Original Instructions
■
Use gloves when maintaining the cutting blades.
■
Maintain the product with care. Keep the cutting blades
sharp and clean for best performance and to reduce
the risk of injury. Follow instructions for lubricating and
changing accessories. Keep handles dry, clean, and
free from oil and grease.
■
After each use, clean the body and handles with a soft,
dry cloth.
■
After each use, remove the debris from the blades with
a stiff brush, and then carefully apply a rust preventative
lubricant before refitting the blade cover. Use a rust
preventative and lubricant spray to apply an even
distribution and reduce the risk of personal injury from
contact with the cutting blades. For information about a
suitable spray product, check with an authorised service
centre.
■
Avoid using solvents when cleaning plastic parts. Most
plastics are susceptible to damage from various types of
commercial solvents and may be damaged by their use.
Use clean cloths to remove dirt, dust, oil, and grease.
■
Always ensure that the ventilation openings are kept
clear of debris.
■
Periodically inspect the cutting blades for damage and
wear.
■
For easier operation and longer blade life, lubricate
the cutting blades before and after each use. Before
lubricating, remove the battery pack and lay the cutting
blades on a flat surface. Apply lightweight machine oil
along the edge of the top blade. Do not apply oil when
the product is running.
SYMBOLS ON THE PRODUCT
Safety alert
Remove the battery pack before
starting any work on the product.
Read and understand all instructions
before operating the product. Follow all
warnings and safety instructions.
Wear eye protection.
Wear non-slip, heavy-duty protective
gloves.
Do not expose the product to rain or
damp conditions.
To prevent serious injury, do not touch
the cutting blades.
Regulatory Compliance Mark (RCM).
The product meets applicable
regulatory requirements.
Guaranteed sound power level
Advertisement
Table of Contents
