Advertisement
Quick Links
Advertisement
Subscribe to Our Youtube Channel
Related Manuals for Minka HYLAND
Summary of Contents for Minka HYLAND
- Page 1 HYLAND 60" Ceiling Fan Indoor/Covered Outdoor Use...
- Page 3 Minka Minka Minka Minka Minka Minka 84085,84087...
- Page 4 MORE NOT LESS KH968 RC400...
- Page 5 1. Fan body 12.Receiver(8 pcs wire nuts) 2. Coupling cover A. Mounting hardware 3. Fan blade(8 pcs) #8-32*25mm screw(2pcs) 4. Canopy #10x38mm wood screw(2 pcs) 5. Light kit plate Φ5*14*1mm flat washer(2 pcs) 6. Light shade 5/32(Φ4.4*9.4*0.5-1.0mm-10) star washer(2pcs) 7. Hanger bracket 3/16(Φ5.2*8.4*1.0mm) spring washer(2pcs) 8.
- Page 6 Minka Minka...
- Page 7 Minka Minka Step 2. Remove the hitch pin and lock pin from downrod assembly. (Fig.6) Step 3. Remove hanger ball from downrod assembly by loosening set screw, removing the cross pin, and sliding hanger ball off downrod. (Fig.7) Step 4.
- Page 8 Note:The universal hand held remote control system is equipped with learning frequency function which has 32 code combination to prevent potential interference from other remote units.The frequency on your receiver and transmitter units have been preset at the factory.(Fig.13).No frequency change is necessary, should you desire to install another fan within the same home or area with a seperate frequency code please see the “frequency interference”troubleshooting section of this instruction manual to learn how to change the frequency.
- Page 9 (Fig.16) (Fig.16) (Fig.16) FIG.16...
-
Page 10: Blade Arm
Step 1. Attach the fan blades to the motor using the screws and washers provided, tighten screws securely. Repeat process with other blades.(Fig.17) WASHER SCREW BLADE BLADE ARM FIG.17 INSTALLING THE LIGHT KIT PLATE Step 1: Remove 1 of 3 screws on light kit adapter and loosen the other 2 screws. (Fig. 18) Step 2: Slide the light kit plate up towards the light kit adapter and place the key holes over the screws on the light kit adapter. - Page 11 Step 1. Remove the 3 screws from the light kit plate and keep it for future use. (Fig.21) (Fig.22) - White to White - Blue to Blue Step 3. Screw back the 3 previously removed screws and tighten the light kit. (Fig.23) SCREW LIGHT KIT MODULE...
- Page 12 Raise light shade up against light kit plate and secure it to the fan by turning the light shade clockwise until snug.DO NOT OVERTIGHTEN.(Fig.24) BLOCK SLOT LIGHT SHADE FIG.24...
- Page 13 Counter clockwise for summer weather operation or clockwise for winter weather operation FIG.25...
- Page 14 FIG.26 FIG.27...
- Page 16 Learn Mode setting procedure. Note: If Multiple fans require to be controlled by a single remote transmitter Minka Recommends Using the Learn Mode setting. Power to both fans will need to be restored at the same time and Press the Learn button on the remote control so that both desired fans can receive the remotes...
- Page 17 0.12 4.69 3014 3.05 0.58 37.96 6314 4,767 Minka...
- Page 18 84085 5127849 84087 5195373...
- Page 20 MKA22072001...
Need help?
Do you have a question about the HYLAND and is the answer not in the manual?
Questions and answers