Subscribe to Our Youtube Channel
Related Manuals for Case IH FARMALL 75C
Summary of Contents for Case IH FARMALL 75C
- Page 1 FARMALL ® Efficient Power Tractor PIN ZDAL00012 and above SERVICE MANUAL Part number 47711472 edition English May 2014...
- Page 2 Link Product / Engine Product Market Product Engine Farmall 75C less cab [ZxALxxxxx] North America F5DFL463A*F017 Farmall 75C with cab [ZxALxxxxx] North America F5DFL463A*F017 47711472 30/05/2014...
- Page 3 Contents INTRODUCTION Engine..................10 [10.001] Engine and crankcase ............. 10.1 [10.216] Fuel tanks .
- Page 4 [25.108] Final drive hub, steering knuckles, and shafts ........25.3 [25.400] Non-powered front axle .
- Page 5 [41.216] Cylinders ................41.5 Wheels ..................
- Page 6 47711472 30/05/2014...
- Page 7 INTRODUCTION 47711472 30/05/2014...
-
Page 8: Table Of Contents
Contents INTRODUCTION Advice ................... 3 Note to the Owner WARNINGS FOR AIR CONDITIONING SYSTEM REPAIR OPERATIONS 4 Safety rules SAFETY REGULATIONS . -
Page 9: Advice
Advice IMPORTANT NOTICE All maintenance and repair work described in this manual must be performed exclusively by CASE IH service techni- cians, in strict accordance with the instructions given and using any specific tools necessary. Anyone performing the operations described herein without strictly following the instructions is personally responsible for any eventual injury or damage to property. -
Page 10: Note To The Owner Warnings For Air Conditioning System Repair Operations
INTRODUCTION Note to the Owner WARNINGS FOR AIR CONDITIONING SYSTEM REPAIR OPERATIONS Starting the system at low temperatures can damage the compressor. Only operate the air conditioner when the engine is hot and the temperature inside the cab is at least 20 °C (68.00 °F). When disconnecting the hoses, close the ends with plastic caps to prevent foreign matter and humidity from getting inside the hoses. -
Page 11: Safety Rules Safety Regulations
INTRODUCTION Safety rules SAFETY REGULATIONS TO PREVENT ACCIDENTS Most accidents or injuries that occur in workshops are the result of non--observance of simple and fundamental safety regulations. For this reason, IN MOST CASES THESE ACCIDENTS CAN BE AVOIDED: by foreseeing possible causes and con- sequently acting with the necessary caution and care. - Page 12 INTRODUCTION • Do not run the engine in confined spaces without suitable ventilation. • Do not smoke, use naked flames, or cause sparks in the area when fuel filling or handling highly inflammable liquids. • Never use naked flames for lighting when working on the machine or checking for leaks. •...
- Page 13 INTRODUCTION • Never lubricate the vehicle when the engine is running. ELECTRICAL SYSTEMS • If it is necessary to use auxiliary batteries, remember that both ends of the cables must be connected as follows: (+) with (+) and (-) with (-). •...
-
Page 14: Personal Safety Cab Air Conditioning System
INTRODUCTION Personal safety CAB AIR CONDITIONING SYSTEM SAFETY REGULATIONS • The refrigerant must be handled with great care in order to avoid personal injury; always use safety goggles and gloves. • Liquid refrigerant can cause freezing of the skin and serious damage to the eyes, sometimes resulting in permanent blindness. -
Page 15: Basic Instructions
INTRODUCTION Basic instructions BATTERY Before commencing any work on the vehicle, always disconnect and isolate the negative lead from the battery, unless otherwise indicated for a specific operation (for example: an operation to be carried out with the engine running), on completion of which the negative lead should be disconnected before proceeding with the work. - Page 16 INTRODUCTION NOTICES Wear limit values indicated for certain parts are recommended, but not binding. The terms “front”, “rear”, “right-hand” and “left-hand” (when referred to different parts) are intended as seen from the driving position with the tractor in the normal direction of movement. MOVING THE TRACTOR WITH THE BATTERY REMOVED External power supply cables should only be connected to the respective positive and negative cable terminals, using efficient clamps that guarantee adequate and secure contact.
-
Page 17: Special Tools Notes For Equipment
INTRODUCTION Special tools NOTES FOR EQUIPMENT The tools that CASE IH propose and illustrate in this manual are: • specifically researched and designed for use with CASE IH vehicles; • necessary to make reliable repair; • accurately built and strictly tested to offer efficient and long--lasting working means. -
Page 18: Consumables
INTRODUCTION Consumables Refueling (*) : – 38.5 L (10.2 US gal) for mechanical transmissions with front loader. – 41.5 L (11.0 US gal) for hydraulic transmissions with front loader. 47711472 30/05/2014... -
Page 19: Part Identification
INTRODUCTION Part identification Use solely genuine parts, which guarantee the same quality, duration and safety as the original parts as they are identical to the ones fitted during production. Only genuine parts can offer this guarantee. When ordering spare parts, always provide the following information: •... - Page 20 INTRODUCTION 47711472 30/05/2014...
- Page 21 SERVICE MANUAL Engine Farmall 75C less cab [ZxALxxxxx] Farmall 75C with cab [ZxALxxxxx] 47711472 30/05/2014...
- Page 22 Contents Engine - 10 [10.001] Engine and crankcase ............. . . 10.1 [10.216] Fuel tanks .
- Page 23 Engine - 10 Engine and crankcase - 001 Farmall 75C less cab [ZxALxxxxx] Farmall 75C with cab [ZxALxxxxx] 47711472 30/05/2014 10.1 [10.001] / 1...
- Page 24 Contents Engine - 10 Engine and crankcase - 001 SERVICE Engine Remove ................. . 3 Install .
Need help?
Do you have a question about the FARMALL 75C and is the answer not in the manual?
Questions and answers
WHAT IS THE HYDRALIC OIL CAPACITY FOR A CASE IH 75C TRACTOR
clutch pedle spring comes loose