mspa F-MO063W Owner's Manual
  1. Manuals
  2. Brands
  3. mspa Manuals
  4. Hot Tub
  5. F-MO063W
  6. Owner's manual

mspa F-MO063W Owner's Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
w w w . t h e - m s p a . c o m
EN
QUESTIONS? PROBLEMS?MISSING PARTS?
For FAQ, Manuals, Videos or Spare Parts, please visit
www.the-mspa.com/support
PLEASE DO NOT RETURN THE PRODUCT TO THE STORE
Due to MSpa's continuous product improvement process, MSpa reserves the right to change the specifications and appearance of its
products, which may result in updates to the instruction manual without prior notice.
Owner's Manual
F-MO063W
CM
C
US
3127647

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the F-MO063W and is the answer not in the manual?

Questions and answers

Related Manuals for mspa F-MO063W

Summary of Contents for mspa F-MO063W

  • Page 1 PLEASE DO NOT RETURN THE PRODUCT TO THE STORE Due to MSpa's continuous product improvement process, MSpa reserves the right to change the specifications and appearance of its 3127647 products, which may result in updates to the instruction manual without prior notice.

  • Page 2: Table Of Contents

    To guide you in your initial MSpa experience, we are pleased to present you with this instruction manual. Please read this manual carefully before using the product for the first time. We are delighted to welcome you to the MSpa family, and look forward to sharing with you the full spectrum of our expertise.

  • Page 3: Safety Precautions

    IMPORTANT SAFETY INSTRUCTIONS For your own safety and that of your product, make sure to follow the safety precautions below. Fail to follow the instruction may result in serious injury, property damage or death. Improper installation or operation will void the warranty.
  • Page 4 The plug of spa shall be more than 3.5m away from the pool. WARNING: WARNING: Spray head must not be used. WARNING: The outlet of Spa must not be connected to any tap or fitting other than those specified. WARNING: Electric installations should fulfill the requirements of local standards.
  • Page 5 A green coloured terminal or a terminal marked G, GR, Ground, Grounding, or the symbol* is located inside the electric box. To reduce the risk of electric shock, this terminal must be connected to the grounding means provided in the electric supply service panel with a continuous copper wire equivalent in size to the circuit conductors supplying this equipment.
  • Page 6 WARNING: Please carefully read the warning label at the first time you are going to use MSpa. Please post this warning label on where is at a distance to MSpa within 1.5m/5’, people in spa can see it clearly. Please retain this information for future reference.

  • Page 7: Specifications

    Seating Water Shape Outside Dimensions Inside Dimensions Height Weight Temp Increasing Rate Capacity Capacity / Code F-MO063W 245 Gal. Round Ø64” (1.63 m) 26” (0.65m) 80.9 lbs (36.7 kg) 1.8-2.7 °F/h Ø68” (1.73 m) (930 L) Mono Control System Specs...
  • Page 8 Water / air channel stoppers NOTE: The drawings are for reference only. Actual products may vary. Not to scale. Use accessories exclusively provided by MSpa for safety reasons. When ordering parts, be sure to quote the MSpa model number and description.

  • Page 9: First Use And Setup Preparation

    FIRST USE AND SETUP PREPARATION Site preparation and requirements ● The spa can be installed indoors or outdoors in around 10 minutes by one or more persons. For household use only. ● The spa must be set up on a flat, smooth and supporting surface that is able to bear the maximum load of the filled spa with the listed maximum number of occupants.

  • Page 10: Spa Setup

    NOTE: Lay out all the parts on the ground and make sure they are all accounted for. For missing or damaged parts contact the appropriate MSpa after-sales service center.
  • Page 11 Inflating the Spa Air Bladder 1. Open the inflation valve and insert the inflation hose into the valve. 2. Slide the pump piston up and down to inflate until it is firm to the touch but not hard. 3. Disconnect the inflation hose from the valve, then close and push in the inflation valve. NOTE: If you need to add some air to the spa tub wall or air bladder after they have been set up, please see the “Inflating the spa tub wall”...

  • Page 12: All-In-One Control Operation

    ALL-IN-ONE CONTROL PANEL LED display Heater Button Filter Button Timer Button Bubble Button - Adjust the bubble level by pressing the button (L1:300W, L2: 450W, L3:700W) UVC Button Ozonator Button Down Button Up Button LED display °C °F Once powered-up, press the RESET on the GFCI. The LED displays the current water temperature automatically. NOTE: The actual water temperature may vary from the temperature displayed on the LED screen by as much as approximately 33.8°F (1°C).

  • Page 13: Water Maintaince And Chemicals

    HEATING TIMER To set the number of hours FROM NOW when the heater will activate: TIMER 1-99H TIMER button to enter pre-setting mode. The TIMER icon shown on the LED display. 1. Press the TIMER UP or DOWN button will cause the LED to flash. While it is flashing, you can adjust the number of hours before heater 2.
  • Page 14 SPA WATER 1. Change the spa water every 3-5 days depending on use. If dirt is visible in the water or if the water becomes cloudy and the correct water chemistry does not clear it up, change the water and clean the spa tub. See the “Cleaning, draining and storage” section for instructions. 2.

  • Page 15: Drainage, Cleaning And Storage

    DRAINAGE, CLEANING AND STORAGE Spa Drainage 1. Turn off all the functions. 2. Connect the drain valve adaptor to a garden hose and point the other end of the garden hose to a suitable draining area. 3. Remove the drain valve cap from the outside of the spa tub and attach the drain valve adaptor to the drain valve. 4.
  • Page 16 How to fix a leaking valve A. Try to tighten the valve 1. Inflate your spa to the max air pressure 2. Insert your valve wrench into the valve and turn the wrench clockwise to tighten the valve onto the spa B.

  • Page 17: Disposal And Environmental Protection

    Clean the parts and tubes that the water goes through 1. Add more water to the minimum line F1 shows 15s after pressing FILTER, HEATING or UVC 2. Clean the parts and tubes that water goes through 3. Contact local MSpa Service Center...
  • Page 18 SPA LEAKING Drainage valve is not closed completely Close the drainage valve. Contact the MSpa Service Center, if spa is still leaking Water leaks from the spa pool body Repair the leaking hole/split with the repair kit material...

  • Page 19: Mspa Limited Warranty

    Where the cost of repairs or replacement is not covered by this warranty, MSpa will advise the owners and the cost shall be charged to the owner.

Table of Contents