For FAQ, Manuals, Videos or Spare Parts, please visit www.the-mspa.com/support Due to MSpa's continuous product improvement process, MSpa reserves the right to change the specifications and appearance of its products, which may result in updates to the instruction manual without prior notice. MSpa Official Site...
IMPORTANT SAFETY INSTRUCTIONS For your own safety and that of your product, make sure to follow the safety precautions below. Fail to follow the instruction may result in serious injury, property damage or death. Improper installation or operation will void the warranty.
Page 4
The plug of spa shall be more than 3.5m away from the pool. WARNING: WARNING: Spray head must not be used. WARNING: The outlet of Spa must not be connected to any tap or fitting other than those specified. WARNING: Electric installations should fulfill the requirements of local standards.
Page 5
A green coloured terminal or a terminal marked G, GR, Ground, Grounding, or the symbol* is located inside the electric box. To reduce the risk of electric shock, this terminal must be connected to the grounding means provided in the electric supply service panel with a continuous copper wire equivalent in size to the circuit conductors supplying this equipment.
Page 6
Warning Label Instruction Please carefully read the warning label at the first time you are going to use MSpa. Please post this warning label on where is at a distance to MSpa within 1.5m/5’, people in spa can see it clearly.
Notify customer service of any damaged or missing parts at the time of purchase. Plastic wood panel *3 Spa liner with Corner Open-end panel *1 Top trim *4 One with MSpa Logo LED light strip beam *4 Jet Control Box Bottom seal *4 Buckle spa cover...
FIRST USE AND SETUP PREPARATION Site preparation and requirements ● The spa can be installed indoors or outdoors in around 15 minutes by 2 persons. For household use only. ● The spa must be set up on a flat, smooth, and supporting surface that can bear the maximum load of the filled spa with the listed maximum number of occupants.
CONTROLLER OPERATION Wi-Fi Icon Low Temperature Warning LED Display Filter Button HEATER Button Ozone Button BUBBLE Button Timer Button Adjust the bubble level by pressing the button (L1:300W, L2:450W, L3:700W ) Up Button DOWN Button JET Button UVC Button LED display °C °F Once powered-up, press the RESET on the GFCI.
Page 12
Unlock Lock NOTE: Always keep the spa cover on to minimize heat loss when heating the water. Make sure the cover, and mostly its side facing water, will not come into contact with the ground or any other dirt when not in use.
Celsius/Fahrenheit Toggle Button The temperature can be displayed in either Celsius or Fahrenheit. Press the DOWN button for 3 seconds to toggle between the two options. SAFETY LOCK Press the UP and DOWN buttons at the same time for 3 seconds to lock/unlock the controller. In safety lock mode, the controller is disabled and the spa retains all previous settings.
WATER MAINTENANCE AND CHEMICALS CAUTION: ALWAYS ENSURE THE SPA IS UNPLUGGED BEFORE STARTING ANY MAINTENANCE WORK TO AVOID THE RISK OF INJURY OR DEATH. FILTER CARTRIDGE MAINTENANCE 1. Inspect and clean the filter cartridge gently after each use. Follow the steps below: NOTE: Change the filter cartridge every 3-5 days, if the filter cartridge remains soiled and discolored.
Water Treatment: ● It is good practice with an existing spa to keep all air jets open and valves closed to allow chemically treated water to flush through all pipework. ● Always follow the chemical manufacturer's instructions and health and hazard warnings. ●...
Page 16
Disassemble Instructions Remove all the parts in the reverse order of the installation steps. NOTE: To remove the liner, use an L-wrench to pry the retaining block out of the side panel slot. Do not drag the liner directly. Spa Bladder Deflation 1.
Storage and Preparation for Future Use 1. Drain and clean the spa by following the “Drainage” and “Spa Cleaning” sections. 2. Refer to the instructions to deflate air bladder. 3. Make sure all the spa components and accessories are thoroughly clean and dry before storage.
Spa in&outlet connection not Tighten the in&outlet connection securely tight SPA LEAKING Drainage valve is not closed Close the drainage valve. Contact the MSpa Service Center, completely if the spa is still leaking Temperature set too low Set a higher temperature...
● This warranty is valid only in the country of purchase in such countries where MSpa sells and services the same model with identical technical specifications.Warranty service outside the country of purchase is limited to the terms and conditions of the corresponding warranty in the country of service.
Need help?
Do you have a question about the OSLO and is the answer not in the manual?
Questions and answers