Other Features - Midea MP05SRWBA3RCM User Manual

DRY operation
· Press the "MODE" button until the "DRY" indicator
light comes on.
· The fan speed or the temperature cannot be
adjusted. The fan motor operates at LOW speed.
(on some models)
NOTE:Keep windows and doors closed for the best
dehumidifying effect. Do not put the duct to window.
FAN operation
· Press the "MODE" button until the"FAN " indicator
light comes on.
· Press the "FAN SPEED" button
controller to choose the fan speed. The temperature
can not be adjusted.
· Do not put the duct to window.
AUTO operation(on some models)
· When you set the air conditioner in AUTO mode, it
will automatically select cooling, heating(cooling
only models without), or fan only operation
depending on what temperature you have selected
and the room temperature.
· The air conditioner will control room temperature
automatically round the temperature point set by
you.
· Under AUTO mode, you can not select the fan speed.
NOTE: Under AUTO mode, both the AUTO mode and
the actual operation mode indicator lights illuminate
for some models.
HEAT operation(cooling only models without)
· Press the "MODE" button until the "HEAT" indicator
light comes on.
· Press the ADJUST buttons "+" or " - " to select your
desired room temperature. The temperature can be
set within a range of 17°C~30°C/62°F~88°F (or 86°F).
· Press the "FAN SPEED" button on the remote
controller to choose the fan speed.

Other features

SLEEP/ECO operation
This feature can be activated from the remote control
ONLY. To activate SLEEP feature, the set temperature
will increase(cooling) or decrease(heating) by 1°C/2°F
(or 1°F) in 30 minutes. The set temperature will then
increase(cooling) or decrease(heating) by another 1°C
/2°F (or 1°F) after an additional 30 minutes. This new
temperature will be maintained for 7 hours before it
Wireless operation(on some models)
Used to initiate the wireless connection mode. For the
first time to use wireless function, press the POWER
button for 3 seconds to initiate the wireless connection
mode . The LED DISPLAY shows 'AP' to indicate you can
set wireless connection. If connection(router) is successful
within 8 minutes, the unit will exit wireless connection
mode automatically and the wireless indicator illuminates.
If connection is failure within 8 minutes, the unit exits
wireless connection mode automatically. After Wireless
connection is successful, for some models you can
press MODE and UP (+) buttons at the same time
on
the remote
for 3 seconds to turn off Wireless function and the LED
DISPLAY shows 'OF' for 3 seconds, press MODE button
and UP(+) to turn on Wireless function and the LED
DISPLAY shows 'O
NOTE: When you restart the wireless function, it may
take a period of time to connect to the network
automatically.
CONSTANT FAN(Press 3s)
VENT CONSTANT(Presse 3s)
n
' for 3 seconds.
Constatnt Fan button(On some models)
In cooling or Dry mode, press the button for
3 seconds to turn on or off the constant fan
function. When the function is turned on, the
constant fan light will illuminate, identifying
the fan continuous run for cooling. When the
function is turned off, the constant fan light
will go out, identifying the fan cycle run with
compressor stop.
FRESH operation(on some models)
Press MODE and DOWN (-) buttons at the same time
for 3 seconds to initiate FRESH feature and the FRESH
light illumiantes on some models, the LED DISPLAY
n
shows 'O ' for 3 seconds. The ion generatoris energized
and will help to purify the air inside. Press it for 3
seconds again to stop the FRESH feature and the FRESH
light turn dark on some models, the LED DISPLAY shows
'OF' for 3 seconds for some units.
returns to the originally selected temperature. This
ends the Sleep mode and the unit will continue to
operate as originally programmed.
NOTE: This feature is unavailabe under FAN or DRY
mode.
FOLLOW ME/TEMP SENSING feature(on some models)
NOTE:This feature can be activated from the remote
control ONLY. The remote control serves as a remote
Page 19
 