Alcatel T78 - Telephone Manual

Table of Contents

Contents

1 BASE STATION KEYS
2 DISPLAY ICONS
3 INSTALLATION AND SETUP
4 USING THE PHONE
5 GENERAL SETTINGS
6 Documents / Resources
- 6.1 References
- 6.2 Download manual

BASE STATION KEYS

PLEASE READ THIS USER'S GUIDE BEFORE USING YOUR PHONE

BASE STATION KEYS

Ring indicator
Delete button
Up button
Out button
Down button
Mute/Contrast button
Phonebook button
Programme button
Memory button
Microphone
Call Blocker button
Speaker button
Flash/Exit button
Speaker volume switch
Menu button
Ringer volume switch

DISPLAY ICONS

Month
Day

Hour
Minute

Afternoon
Voice mail

Morning
Speakerphone

Mute
Repeat

New CID*
Call-log number*

Call waiting*
Name display*

Phone number display*
Call block

* Subject to subscription and availability of the service from the fixed line operator.

INSTALLATION AND SETUP

Your phone should be placed on a level surface, such as a desk or table top, or you can mount it on a wall.

DESKTOP INSTALLATION

Connecting the handset.
Connecting the telephone line.

WALL INSTALLATION

Rotate the wall mounting knob as shown in the following layout:

The knob is designed to keep this unit in place when the telephone is vertical on the wall.
Install the base unit to the wall and then plug one end of line cord into junction box and the other end into modular telephone line jack marked " ". (Fig 4)
Fix the telephone on the wall. (Fig. 5)

Call Blocker
This telephone is built-in with Basic Call Block feature*. This feature will help you avoid nuisance calls by only allowing some numbers to make your phone ring.
Default setting of Call Block in this telephone is OFF but you can activate it via your phone settings, as explained in the following paragraphs.
*This feature requires a subscription of Caller Line Identification service from your telephone service provider.

Call Block overview

Setting	Explanations
BLOCKLIST	Call block is on. Numbers registered in the block list will not go through and phone will not ring and call drop immediately. Numbers can be adding to the list while the phone is ringing on / after see part 1)
ALLOW PB	For those calls matched with one touch (M1...M8) or 2 touch (E0..E9) numbers will allow call through. And, Caller information show on display as normal( to enable, see part 2) For those call does not matched with M1..M8 or E0...E9, phone will not ring and keep silent and call will drop immediately.
BLOCK ANONYMOUS	This feature allows you to block call that do not have a number attached to them (ie private calls, international calls, etc).
BLOCK OFF	Call Block function (Block all call with numbers) is Disabled. Call block icon is turned off.

Manual call block mode
Manual call block is the easiest option when starting out. All calling numbers registered in your Blocklist will be blocked. You can add/remove numbers from that list at any time. is OFF.
How to block an incoming call:
When the phone is ringing and before answering, press will terminate the call and offer you the option to register the number to the blacklist in one click.

if you don't confirm, the number will not be added to the Blocklist and the next call will go through normally.
Set Block mode (Call block is OFF by default)
In idle mode, Press for 3 sec., press or to select: BLOCKLIST / ALLOW PB / BLOCK ANONYMOUS / BLOCK OFF. Press again, confirmation Tone will be heard and Block mode setup finished.
After you setup the any options above, the call block icon will be displayed on the LCD.
1. Add numbers to Blocklist
  In idle mode, Press or key, review the dial in number in call list. Press once. Number will be stored into blocklist.
2. Review or Delete numbers in Blocklist
  In idle mode, Press once, blocked numbers will be displayed on LCD or "NO CALLS" if no numbers has been stored.
  Use or for review the blocked numbers in list.
  Press once, blocked numbers will be deleted on LCD.
  OR
  Long press > 3 sec to Erase ALL numbers in blocklist. LCD will show "NO CALLS".
3. Set Allow PB (Allow contacts)
  In idle mode,
  Press key for > 3 sec.,press or to ALLOW PB and press once. confirmation Tone will be heard and PB ALLOW mode setup finished.
4. Set Block Anonymous
  In idle mode,
  Press key for > 3 sec., press or to "BLOCK ANONYMOUS " and press once. confirmation Tone will be heard and Block Anonymous mode setup finished.
5. Set Block off..
  In idle mode,
  Press key for > 3 sec., press or to "BLOCK OFF" and press once. confirmation Tone will be heard and Block off is set means Call Block (ALL) is disable. Setup finished.

SET LANGUAGE AND FLASHTIME TO OPERATE CORRECTLY ON YOUR NETWORK:

Press on MENU / or SELECT LANGUAGE / MENU / or to select language desire / MENU / R
Press on MENU / or SET FLASH TIME / MENU/ or to select flash time FLASH 100ms / FLASH 300ms / FLASH 600ms or FLASH 1000ms / MENU / R

USING THE PHONE

RECEIVE AND END A CALL

MAKE A CALL

or either before or after dialing your number or, dial number /
From redial list:

/ or
or /

From call log list*:

or to select the caller number / or
or to select the caller number / ... to add number prior to the select number / or

From direct memories:

to select memory location from M1~M8 or + ... / or
or / to select memory location from M1~M8 or + ...

MUTE THE MICROPHONE:
In off-hook state, user can press the button to access mute function. When CONTRAST/MUTE is on, the CONTRAST/MUTE indicator will show on the screen. Press the button to exit mute function and resume normal conversation. In on-hook state, user can press the button to select the LCD Contrast (1 ~ 5 choice, default is 3).

DELETE CALLER ID NUMBER:

Delete a Caller ID number: or to select the number /
Delete all Caller ID numbers: or to select the number / long press to confirm DELETE ALL? /

STORE NUMBER:

Store a telephone number: / ... to select memory location or to select M1~M8 / / ... to input number / / ... to input name / / R.
Store an incoming call number: or to select the number // ... to select memory location, or to select M1~M8 / to confirm number selecting / ... to input name / / R.
Store an outgoing number: ... to select the number // ... to select memory location, or to select M1~M8 / to confirm number storing / ... to input name / / R.