Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Amada GS-2
Summary of Contents for Amada GS-2
- Page 1 HAND-HELD WELDING HEAD GS-2 OPERATION MANUAL Z11M0895E-06...
-
Page 2: Table Of Contents
GS-2 Thank you for purchasing our Hand-Held Welding Head GS-2. This operation manual describes its method of operation and precautions for use. Read this operation manual carefully prior to use. Store appropriately for ready reference. Contents 1. Special Precautions (1) Safety Precautions ................ 1 (2) Precautions for Handling ............... -
Page 3: Special Precautions
GS-2 1. Special Precautions (1) Safety Precautions CAUTION ！ Before using, be sure to read this operation manual to operate this machine correctly. This operation manual may include some items that do Denotes operations and practices not correspond to your use. However,... - Page 4 GS-2 DANGER ！ Do not disassemble, repair, or modify this machine in any case. Otherwise, an electric shock or injury will occur. When internal inspection or repair is required, make contact with us. WARNING ！ Do not put your hands between the electrodes.
- Page 5 GS-2 CAUTION ！ Do not splash water on the product. Water splashed over the electric parts can cause electric shock and short circuits. Do not give excessive force to connecting cables. Do not bend, pull, or pinch any cable forcibly. If the cable is damaged, it will cause an electric shock, short circuit, or firing.
-
Page 6: Precautions For Handling
GS-2 (2) Precautions for Handling Do not install this product in the following: Damp places where humidity is 90% or higher, - Dusty places, - Places where chemicals are handled, - Places where corrosive gas is generated, - Places near a high noise source, - Hot or cold places where temperatures are above 40C or below 5C, and... -
Page 7: Features
GS-2 2. Features Compact, light-weight handy type Pressurization power detection mechanism built-in for stable welding 2. Features... -
Page 8: Name And Functions Of Each Section
GS-2 3. Name and Functions of Each Section 3. Name and Functions of Each Section... - Page 9 GS-2 (1) Pressure adjusting screw This screw is used to adjust the pressure at welding. Turn the pressure screw to set the required pressure. (2) Pressure sensor The pressure sensor is used to make sure that pressure is applied to the weldment at welding.
-
Page 10: Connecting The Pressure Signal Cable
GS-2 4. Connecting the Pressure Signal Cable [Pressure signal cable terminal] (WT) (BK) Selecting F terminal 1: WT (NC) 2: BK (COM) Microswitch 2P connector Selecting 2P connector 4. Connecting the Pressure Signal Cable... -
Page 11: Operating Method
GS-2 5. Operating Method When holding the operation lever to make adjustments (1) and (2) as referred to below, be sure to set the welding power supply off. (1) Adjustment of the electrode holder Make alignment of the spacing of electrode provisionally by approximation at first and then make final adjustment of direction and length of electrode protruding from the base of the holder. -
Page 12: Product Specifications
GS-2 6. Product Specifications 3 Electrode diameter Electrode holder 90° or 45° selectable Signal output Micro switch Pressure force 1.5 to 5 kg Secondary conductor (option) H-050-1000-06-08-N (Item No.: 1006016) Weight 500 g 6. Product Specifications -10-... -
Page 13: Outline Drawings
GS-2 7. Outline Drawings (for mounting secondary conductor) For fixing the lower electrode holder 3 (Electrode dia.) Pressure adjusting screw For fixing the upper electrode holder (clearance hole for hexagon wrench) 7. Outline Drawings -11-... - Page 14 GS-2 Electrode holder Vertical: standard Vertical: long Inclined Welding electrode Vertical Inclined 7. Outline Drawings -12-...
Need help?
Do you have a question about the GS-2 and is the answer not in the manual?
Questions and answers