Related Manuals for Reef Factory RFLK01
Summary of Contents for Reef Factory RFLK01
- Page 1 ver. 2.0.1 Level keeper User Manual Dear customer, thank you for your purchase. ENGLISH www.reeffactory.com...
-
Page 2: Table Of Contents
IMPORTANT INFORMATION! Please read the entire user manual very carefully before setting up and using the device. There may be slight differences in the content between what is presented on the screen of the device and the descriptions in the manual. Reef Factory 2022 User manual Level keeper ©... - Page 3 If you have a low water level in your tank, you can install a level sensor as shown in the picture on the left. However, if your tank has a high water level, you can mount the sensor as shown in the picture on the right. Reef Factory 2022 User manual Level keeper ©...
-
Page 4: Assembly Of The Device
The device should be hung where it cannot be splashed with water and the humidity is low. Reef Factory 2022 User manual Level keeper ©... - Page 5 Using the power cord included in the set, connect the device to the main socket. Insert the power cord into a tightly fitting socket, and make sure that the cord is not loose. Reef Factory 2022 User manual Level keeper ©...
-
Page 6: Initial Configuration
“Add an aquarium” in the lower left corner of the screen and provide the necessary information. If you already have your aquarium in the Smart Reef app, proceed to the next step. Reef Factory 2022 User manual Level keeper ©... - Page 7 This allows the app to connect devices to Wi-Fi networks more easily. Select from the scrolling list the device you want to add to your Smart Reef account and press “NEXT”. Reef Factory 2022 User manual Level keeper ©...
- Page 8 NOTE: Reef Factory devices only support the 2.4 GHz Wi-Fi network band. If your router generates 2.4 GHz and 5 GHz bands, indicate the name of the 2.4 GHz network.
- Page 9 Allow the Smart Reef app, to temporarily connect to set up a Wi-Fi network. Congratulations! The device has been correctly added to your Smart Reef account and will appear in the list of devices within 60 seconds. Reef Factory 2022 User manual Level keeper ©...
-
Page 10: Configuration Of The Device Operation
- 30 minutes mode - this mode will cause a specific amount of water to be refilled to the tank every 30 minutes - 10 minutes mode - this mode will cause a specific amount of water to be refilled to the tank every 10 minutes Reef Factory 2022 User manual Level keeper ©... - Page 11 The level sensors operate simultaneously and measure the water level continuously. The use of two liquid level sensors additionally protects your tank against liquid overflow in the event of improper operation of one of the sensors, e.g. blockage due to contamination). Reef Factory 2022 User manual Level keeper ©...
-
Page 12: Calibrating The Device
In the device menu, in the lower right corner, press the button "CALIBRATE". Due to the different pump capacities, enter a calibration time that is suitable for the water refilling pump. Reef Factory 2022 User manual Level keeper ©... - Page 13 After this, a pump calibration message will appear. After the calibration is completed, enter the amount of pumped fluid. Remember to put the water-filling hose back into the system after calibration. Reef Factory 2022 User manual Level keeper ©...
- Page 14 Select from the list the period after which the device should remind you to calibrate. The centre of the screen will display the current fluid level status and how much water has been added to your tank on a given day. Reef Factory 2022 User manual Level keeper ©...
-
Page 15: Additional Features Of The Device
TEMPORARY TURN OFF - this function is used to temporarily turn off the refilling system, e.g. when performing service in the tank. BACKLIGHT - using this function, you can turn on or off the light bar of the device. Reef Factory 2022 User manual Level keeper ©... -
Page 16: Resetting The Device
Enter your current password (default is reeffactory) then press "OK". In the next step, enter a new password and press "OK", then confirm the new password and press "OK". Congratulations! The password has been changed successfully. Reef Factory 2022 User manual Level keeper ©... -
Page 17: Replacing The Fuses
ATTENTION! Disconnect the device from the mains before replacing the fuses. Reef Factory 2022 User manual Level keeper ©... -
Page 18: Device Update
After pressing the "OK" button, the device will automatically update. During the update, do not disconnect the device from the power supply. If the update doesn't complete within 30 minutes, reset your device. Reef Factory 2022 User manual Level keeper ©... -
Page 19: Information And Warnings
Reef Factory 2022 User manual Level keeper ©... - Page 20 Any changes or modifications not expressly approved by Reef Factory could void the user's authority to operate the RF Module and/or the product that incorporates the RF Module. The user is cautioned to maintain a 20 cm (8 inch) spacing from the product to ensure compliance with FCC regulations.
-
Page 21: Warranty Conditions
XI. Warranty conditions Reef Factory Sp. z o.o. does not guarantee the uninterrupted or error-free operation of the product. The warranty covers only technical hardware problems that occurred during the warranty period and under normal conditions of use. Reef Factory Sp. z o.o. products are under warranty for a period of: ●... - Page 22 16. Reef Factory Sp. z o.o. is not responsible for the lack of compatibility of the product with other manufacturers’ accessories or devices used by the customer. This applies to network devices, which may limit the possibility of connection and data exchange between the device and the product.
-
Page 23: Technical Information
285x165x60 Weight 850 g The device is manufactured with different versions of power cords and power sockets, depending on the country in which it will be used Need our help? - support@reeffactory.com Reef Factory 2022 User manual Level keeper ©... -
Page 24: Knowledge Base And Technical Support
XIII. Knowledge base and technical support Need our help? Check out our knowledge base! Help Center - Jira Service Management Have more questions? Use the form in the link above or write us an email - support@reeffactory.com Reef Factory 2022 User manual Level keeper ©...
Need help?
Do you have a question about the RFLK01 and is the answer not in the manual?
Questions and answers