Olivetti FAX System M-New Service Manual page 57

3KH-3
Selection of Transmit Terminal Identification (TTI)
The transmit terminal identification (TTI) is the informa-
tion about the machine (transmit terminal) to be printed
out on FAX on the receiving system. The information
includes transmission date and time, the number of
transmission pages, and the fax number. This machine
enables the user to select if the TTI is printed out on the
fax on the receiving system. Regarding the location of the
information to be printed, you can select inside or outside
of the page image being send.
Note: You can specify a separate TTI for fax transmis-
sions and Internet fax transmissions.
1. Press [FAX/i-FAX], [Next] of Transmission, [Next] of
FAX (Send Fax) or i- FAX (Send i-FAX) and then
press [Change] of TTI.
2. Select [Off], [Outside] or [Inside].
3. Press [OK].
To exit from this setup, press [Close] several times
until the System Menu default screen is displayed.
Media type for print output
Specify the paper type to be used for print output of the
received fax.
1. Press [FAX/i-FAX], [Next] of Reception, [Next] of
Basic and then [Change] of Media Type.
2. Select the desired paper type.
If no specific paper type is selected, press [All
Media Types].
Setting: All media type/Plain/Rough/Recycled/
Bond/Color/High Quality/Custom 1 to 8
3. Press [OK].
To exit from this setup, press [Close] several times
until the System Menu default screen is displayed.
MP tray paper output
Select whether to use the MP tray paper when printing
out the received fax.
1. Press [FAX/i-FAX], [Next] of Reception, [Next] of
Basic and then [Change] of Multi Purpose Tray.
2. Select [On] or [Off].
3. Press [OK].
To exit from this setup, press [Close] several times
until the System Menu default screen is displayed.
Reduced reception
Reduce the print size when the reception size is larger
than the paper size.
1. Press [FAX/i-FAX], [Next] of Reception, [Next] of
Basic, and [Change] of Reduced RX Size.
2. Select [Off] or [On].
3. Press [OK].
To exit from this setup, press [Close] several times
until the System Menu default screen is displayed.
1-3-32
Reception Date/Time
Reception Date/Time function adds the reception date/
time, sender information and number of pages on the top
of each page when the message is printed out.
Notes: When the received data is printed on multiple
pages, the reception date/time is printed on the fist page
only. It is not printed on the pages that follow.
When the received fax data is forwarded after retrieving it
from memory, the reception date/time is not added to the
forwarded data.
1. Press [FAX/i-FAX], [Next] of Reception, [Next] of
Basic, and [Change] of Reception Date/Time.
2. Press [On].
3. Press [OK].
To exit from this setup, press [Close] several times
until the System Menu default screen is displayed.
Duplex print output
When received multiple pages of data are the same
width, they can be printed out on both sides of the paper
having the same width as the data.
1. Press [FAX/i-FAX], [Next] of Reception, [Next] of
Basic and then [Change] of Duplex Printing.
2. Select [On] or [Off].
3. Press [OK].
To exit from this setup, press [Close] several times
until the System Menu default screen is displayed.
2 in 1 reception
Print two pages of the original at a time on one Letter or
A4 size sheet of paper when you receive a multi-page
Statement or A5 size original.
Note: If you specify 2 in 1 reception and duplex print out-
put at the same time, 2 in 1 reception is disabled.
1. Press [FAX/i-FAX], [Next] of Reception, [Next] of
Basic and then [Change] of 2 in 1 Print.
2. Select [Off] or [On].
3. Press [OK].
To exit from this setup, press [Close] several times
until the System Menu default screen is displayed.
Remote switch function
Start fax reception by operation from the connected tele-
phone set.
Note: In order to use remote switch, it is necessary to
connect the tone signal-sending telephone set (commer-
cially available product) to the machine.
1. Press [FAX/i-FAX], [Next] of Reception, [Next] of
FAX, and then [Change] of Remote SW Dial.
2. Enter the number using the [+]/[-] or numeric keys.
Setting range: 00 to 99
Initial setting: 55
3. Press [OK].
To exit from this setup, press [Close] several times
until the System Menu default screen is displayed.
Service Manual Y108810-2