Table of Contents
Advertisement
Function Buttons
See Figure 5 for illustration for remote function buttons.
•
Up arrow button. Press to increase the temperature
setpoint or to scroll through settings options.
•
On/Off button. Press to turn the indoor unit on or off.
•
Mode button. Press to scroll through the operation
modes: Auto → Cool → Dry → Heat → Fan.
•
Fan speed. Press to scroll through the fan speeds:
Auto → Low → Med → High.
•
Sleep button. Press to activate "night-mode". This will
automatically increase (cooling) the setpoint 2°F (1°C)
per hour for the first two hours. The modified setpoint
will be set for five hours. After seven total hours the
indoor unit will resume the previously set point.
NOTE: SLEEP mode is only available when the unit is
in COOL, HEAT or AUTO mode.
•
Turbo button. Press to active turbo mode. The indoor
unit will ramp up to reach the setpoint more quickly.
After reaching the set point or after 30 minutes,
the indoor unit will resume the previous operating
conditions.
•
Self Clean button. Press to activate self cleaning
mode. In cooling or dry mode only, the indoor unit will
temporarily change operation to allow condensate on
the indoor unit coil to evaporate, and then will return to
the previous operating conditions.
•
Down arrow button. Press to decrease the
temperature setpoint or scroll through settings options.
•
Silence Button. Press and release to activate quiet
mode operation. The indoor unit will change operation
to provide the quietest sound possible.
NOTE: Quiet mode operation may result in insufficient
cooling or heating capacity. Press and release the
Silence button again to stop quiet mode operation.
•
FP button (Frost Prevention mode). Press and hold
for two seconds to activate frost prevention mode. In
heating mode only, the indoor unit will operate at a
46°F set point and the indoor unit display will show
"FP". To cancel, push the "ON/OFF", "SLEEP", "FP",
"MODE", "FAN SPEED" or "UP/DOWN" buttons.
•
Timer ON button. Press to set the number of hours of
delay before the indoor unit begins operation.
Timer OFF button. Press to set the number of hours
•
of delay before the indoor unit stops operation.
•
Swing button. Press once to initiate louver left and
right oscillation. Press again to stop louver oscillation.
Louvers remain in place where stopped. Not available
in all indoor unit models.
Page 6 of 8
•
Direct (Direction) button. Press to move louvers up
and down in six degree increments. Louvers remain in
place where stopped.
•
LED button. Press the LED button to turn on the
indoor unit display (on units with display). Press the
button again to turn off the display.
•
Follow Me button. Press to activate the wireless
remote's air temperature sensor. This will also transfer
the temperature sensing function from the indoor unit
to the remote. The indoor unit's air temperature sensor
will be disabled. The indoor unit will regulate the room
temperature based on the temperature sensor in the
remote controller, rather than the sensor in the indoor
unit.
•
The remote controller will send the indoor unit a signal
every three minutes. If the indoor unit doesn't receive
the signal for seven minutes, or if the button is pressed
again, the Follow Me function will terminate.
•
The remote controller must remain pointed toward the
indoor unit and must be within 26 feet (8 meters) of
the unit. Do not remove the controller from the room
or obstruct the signal of the remote controller during
Follow Me operation.
Display
See Figure 6 for illustration of remote control.
•
Remote controller On. Icon displays to indicate that
the remote controller is on.
•
Transmitting display. Icon blinks once when a signal
is sent from the wireless remote controller.
•
Operation
current
mode
button to scroll through the operation modes:
Auto → Cool → Dry → Heat → Fan.
•
Setpoint or Room Temperature. Displays the setpoint
temperature during normal operation. Displays the
room temperature when in Follow me mode. Adjust the
setpoint with up and down arrow buttons. No display
when unit is in Fan mode.
•
Timer ON/OFF. These icons light up to indicate that
the indoor unit has a timed auto-start or auto-stop set
up.
•
Battery charge status. Icon displays charge status of
wireless remote controller batteries.
•
Sleep mode. Icon displays to indicate that sleep mode
operation is on.
•
Follow me. This icon displays when the air temperature
sensor in the wireless remote controller is the sensor
being used by the indoor unit. When this function is off,
the indoor unit uses a built-in sensor.
•
Fan speed. Displays the current fan speed.
Issue 2011
mode.
These
icons
of
operation.
Press
show
the
the
mode
507949-01
Advertisement
Table of Contents
