Program Loudmouth; Features; Feature Codes - Ritron Jobcom J Series J-U410 Owner's Manual

3.5

Program Loudmouth

The wireless speaker can be field programmed for a variety of features. Refer to
available for field programming. In our example we will program an LM-U450 for Record and Play operation. The
™ is set from the factory with these √ options enabled.
Loudmouth
13
1.
2.
3.
4.
5.
6.
7.
8.
Table 5: Loudmouth
Code Feature
Special Features
21 Reset to Factory Defaults
22 Display Radio Revision
23 Pre-Announce Tone – On
24 Pre-Announce Tone – Off
25 Record and Play – On
26 Record and Play – Off
27 One Speaker
28 Two Speakers
29 Weather Alert – On
20 Weather Alert – Off
Battery Powered Operation
41 Battery Operation – On
42 Battery Operation - Off
43 Power Save – On
44 Power Save – Off
™

Features

Refer to Table 5 to determine the two-digit feature code and write it down.
Press and HOLD the PROGRAM button (See
for location). A "P" will appear on the program display as you enter program mode and the
radio will beep rapidly.
Release the PROGRAM button after the beeping has stopped. The radio will emit a triple
beep indicating that the radio is in program mode and a hyphen will appear on the program
display.
Scroll to the character "A" by clicking the PROGRAM button until the program display
shows the correct character. Pause—the radio will sound a low tone and show a hyphen
across the center of the display to indicate that it is ready to accept the first digit of the
Feature code.
st
Enter the 1 digit of the feature code by clicking the PROGRAM button until the program
display shows the desired number. Pause—the radio will sound a low tone and show a
hyphen across the center of the display to indicate that it is ready to accept the next digit.
nd
Enter the 2 digit of the feature code by clicking the PROGRAM button until the program
display shows the desired number. Pause—the radio sounds a low tone and will show a
hyphen across the center of the display to indicate that it is ready to accept the next digit.
Press and release the ENTER button to save your programming. A triple beep will sound to
indicate that programming was successful and a hyphen will appear on the program
display. The radio is now ready for another program entry.
NOTE: An error tone will sound if you attempt to save an incorrect code, an "E" will appear
on the display. Check the digits you are attempting to enter, then re-enter.
Once you have made your final program entry, press the ENTER button a final time to exit
programming mode. The Program display will be blank and the radio will be ready for use.
™
The Loudmouth will exit program mode automatically after 30 seconds if no program
entries are attempted.
™

Feature Codes

Default Description
Resets Wireless Speaker to Factory default programming.
Loudmouth
revision. This is helpful when troubleshooting the radio.
√
Enable this feature to play a short tone over the Loudmouth
whenever it receives a signal.
Disable Pre-Announce Tone
When set received messages are recorded and played back over the
Loudmouth
√
Disable Record and Play feature
√
Set when one speaker is used for maximum available volume.
Set when two speakers are used for maximum available volume.
Enable this feature to receive local NOAA weather radio emergerncy
broadcasts from the National Weather Service and play them over the
Loudmouth
√
Disable Weather Alert
Set to extend battery life when powering the Loudmouth
battery.
√
Set when powering the Loudmouth with the RPS-1A or an external DC
supply.
Set to enable Power Save operation for battery powered Loudmouth. This
option will have no effect unless Battery Operation – On is set.
√
Set to disable Power Save operation for RPS-1A powered Loudmouth.
Section 3
Table 5
Loudmouth
™
will display a sequence of 6 digits to identify operating code
™
speaker immediately after the received signal is removed.
™
speaker. This feature is only available on the LM-V150.
Programming
for the two digit codes
™
receiver assembly on page 2
™
speaker
™
with an external
18