Toyotomi Toyostove Laser 300 Installation And Operation Instruction Manual page 13

Laser 300_Type A_US.qxd 15.3.26 16:11 ページ 13
WEEKLY TIMER OPERATION
1. Set the Weekly Timer
Note: The following programs are set at the factory in advance.
Program #
P01
P02
P03
P04
P05
P06
P07
P08
After setting the current time and a day of the week, press the "TIMER" button to enter the weekly timer setting
mode. The "TIMER" is shown on the display. When the "TIMER" button is pressed during setting of the weekly
timer, the "TIMER" sign disappeared and the current clock time and a day of the week are shown on the display.
Note: You cannot enter the weekly timer setting mode, while in operation and AUTO operation mode, on.
1) Select the program number
Press the "▲MIN." button or the "▼HOUR" button to select the program number.
The number of program numbers is 30. The non-set program number will flash on the display. In case of the first
setting of the weekly timer, "P01" is shown on the display and will blink. In case that the program is already set,
the next number of the biggest setting program number is shown on the display. If the program is set until "P30",
"P30" is shown on the display and will blink. Even though all program number are set to "P30", if there is any
non-set program number, the smallest non-set program number is shown on the display.
When pressing the "▲MIN." button, the sign will change as follows.
"P01" ➞ "P02" ➞ ··· ➞ "P29" ➞ "P30"
When pressing the "▲MIN." button at the position of "P30", you can hear a beep sound and "P01" is not
changed any more.
When pressing the "▼HOUR" button, the sign will change as follows.
"P30" ➞ "P29" ➞ ··· ➞ "P02" ➞ "P01"
When pressig the "▼HOUR" button at the position of "P01", you can hear a beep sound and "P01" is not
changed any more.
Example:
In case that "P01" and "P02" programs are set and "P03" is not set, the display shows as follows.
"P01" – solid ⇔ "P02" – solid ⇔ "P03" – flashing 3
In case that "P01" and "P04" programs are set and "P02" and "P03" are not set, the display is indicated as
follows.
"P01" – solid ⇔ "P02" – flashing 3 ⇔ "P03" – flashing 3 ⇔ "P04" – solid ⇔ "P05" – flashing 3
When a non-set program number is shown on the display, all of a day of the week will blink.
Press the "SET" button to move to the next step (Set the timer).
The program number memory is cleared by holding the "CLEAR" button continuously for 3 seconds.
Clock Time Temp.
AM 6:00 68˚F (20˚C)
AM 8:30 62˚F (16˚C)
PM 5:00 68˚F (20˚C)
PM 11:00 62˚F (16˚C)
AM 7:00 68˚F (20˚C)
AM 10:00 62˚F (16˚C)
PM 4:00 68˚F (20˚C)
PM 11:00 62˚F (16˚C)
Day
"MON" "TUE" "WED" "THU" "FRI"
"MON" "TUE" "WED" "THU" "FRI"
"MON" "TUE" "WED" "THU" "FRI"
"MON" "TUE" "WED" "THU" "FRI"
"SUN" "SAT"
"SUN" "SAT"
"SUN" "SAT"
"SUN" "SAT"
13