Related Manuals for Oliver 6305
Summary of Contents for Oliver 6305
- Page 1 Sander Model 6305 Owner’s Manual For Models Manufactured Since 05/2015 175381 Oliver Machinery 1-800-559-5065 921 Thomas Ave SW, Renton, WA 98057 Stock Number: 6305.001 info@olivermachinery.net Manual Version: 2.0.0 WWW.OLIVERMACHINERY.NET...
- Page 3 USAGE OF SAFETY AND PROTECTION DEVICES. OLIVER MACHINERY DISCLAIMS ANY LIABILITY FOR MACHINES THAT HAVE BEEN ALTERED OR ABUSED. OLIVER MACHINERY RESERVES THE RIGHT TO EFFECT AT ANY TIME, WITHOUT PRIOR NOTICE, THOSE ALTERATIONS TO PARTS, FITTINGS, AND ACCESSORY EQUIPMENT WHICH THEY MAY DEEM NECESSARY FOR ANY REASON WHATSOEVER.
- Page 4 Edge Sanding ············································ 30 Electricals ···············································13 Horizontal Sanding ··································· 31 Minimum Circuit Size Required for Model Contour Sanding ······································· 32 6305 Sander ············································· 13 Accessories ············································ 33 Grounding ················································ 13 Maintenance ········································· 34 Electrical Wiring ······································· 14 Changing Sanding Belt ······························ 35 Setup ······················································15...
- Page 5 Introduction Thank you for choosing Oliver! This manual contains important information on how to safely set up, operate, and maintain this machine. Please take the time to read through this manual, and make sure you understand all instructions. While this manual may provide tips on optimizing the result of your workpiece, the manual is not intended as a substitute for formal woodworking training.
- Page 6 Specifications Quick View Model 6305 Sander Stock Number 6305.001 Power Requirement 115V / 230V, 1Ph, 60Hz Motor TEFC 1.5HP, 115V / 230V, 1Ph Sanding Belt Size 6” x 89” Sanding Belt Tilt 0° - 90° Dimensions 52-1/2“(W) x 23”(D) x 48”(H) Footprint 21-1/2”(W) x 16-1/2”(D)
- Page 7 Dust Port Size 4” Minimum CFM Required 650 CFM Sound Rating @ 2’ distance 100 dB Others Serial Number Location On the back of the machine stand. Certification CSA 175381 Country of Origin Taiwan 7 | Page 6305 Sander OLIVERMACHINERY.NET...
- Page 8 Identification 8 | Page Oliver Machinery 6305 Sander...
- Page 9 9 | Page 6305 Sander OLIVERMACHINERY.NET...
- Page 10 Safety Oliver Machinery has made every attempt to provide a safe, reliable, easy-to-use piece of machinery. Safety, however, is ultimately depending on the individual machine operator. Before operating this machine, please become familiar with the following safety labels and guidelines.
- Page 11 13. PROPER USE: Do not use this machine for anything other than its intended use. If used for other purposes, Oliver Machinery disclaims any real or implied warranty and holds itself harmless for any injury or damage which may result from that use.
- Page 12 Correct Wrong After Operation STOP THE MACHINE when the operator leaves the machine for any reason. WAIT until the motor comes to a complete stop. CLEAN UP before departure. 12 | Page Oliver Machinery 6305 Sander...
- Page 13 Please ensure the electrical circuit for this machine meets the minimum circuit size requirement. The minimum circuit size requirement applies to a dedicated circuit that provides power to one 6305 Sander. If more machines are sharing the same circuit, consult a qualified electrician to ensure the designated circuit is properly sized for safe operation.
- Page 14 *NR: Not Recommended Use properly sized wires that meet or exceed the power requirement of your machine. Using undersized wires may cause overheating and increase the risk of fire WARNING and machine damage. 14 | Page Oliver Machinery 6305 Sander...
- Page 15 Air resistance and leakage in a dust collection system impact its effectiveness. Use a dust collection system that is rated above 650 CFM at the dust port. Doing so CAUTION improves air quality in the workplace, and prevents the machine from jamming. 15 | Page 6305 Sander OLIVERMACHINERY.NET...
- Page 16 On the day of delivery, please be sure help is available to move the machine to its final location. 6305 Sander has a gross weight of 264 lbs. and a net weight of 246 lbs. Safe moving techniques and proper lifting equipment are required, or serious WARNING personal injury may occur.
- Page 17 Item Description Quantity Item Description Quantity Contour sanding table Fender washers (5/16”) Mounting Bracket Washers (5/16”) Contour sanding table Lock washers (5/16”) bracket Hex nuts (5/16”) Mounting hardware 1 set Hex nuts (5/16”) Support rod 17 | Page 6305 Sander OLIVERMACHINERY.NET...
- Page 18 Disposable gloves Protection Paper Towel Cleaning WD-40 Cleaning Rust Inhibitor Cast iron table top rust protection. 12mm Wrench (1 Pair) Machine Assembly Straight Head Screw Driver Machine Assembly Philips Head Screw Driver Machine Assembly 18 | Page Oliver Machinery 6305 Sander...
- Page 19 2. Insert a round head screw and a washer into the rubber feet. 3. Mount the feet at the bottom of the side panel. Thread a nut into the screw. 19 | Page 6305 Sander OLIVERMACHINERY.NET...
- Page 20 For this step, you will need: 1. The panels with rubber feet already mounted: 2. All mounting hardware in “Group 2”: Item Description Quantity Fender washers (5/16”) Washers (5/16”) Lock washers (5/16”) Hex nuts (5/16”) Hex nuts (5/16”) 20 | Page Oliver Machinery 6305 Sander...
- Page 21 Tighten the bolts to hold the panels together, but do not fully tighten them yet. 4. Place the cabinet right side up. Make sure it does not rock on the ground. Adjust the joints of the panels as needed. Fully tighten all the bolts before the next step. 21 | Page 6305 Sander OLIVERMACHINERY.NET...
- Page 22 Once all rust protectant is removed, routinely coat the tabletops with rust preventive such as Boeshield® T-9 or paste wax. Do not use rust preventives that contain silicone, which is known to interfere with certain finishes and glues. 22 | Page Oliver Machinery 6305 Sander...
- Page 23 8. Tighten the sanding belt by moving the belt tensioning lever back to the “Tight” position. When the sanding belt is properly tensioned, it should not slip off from the drums. 9. Reinstall the belt guard and tighten the lock knobs. 23 | Page 6305 Sander OLIVERMACHINERY.NET...
- Page 24 2. The stop bracket mounting holes are located on top of the platen near the drive drum. Insert the stop bracket pin into the hole as shown in the picture. 3. Secure the bracket with a lock knob. 24 | Page Oliver Machinery 6305 Sander...
- Page 25 Align the flat surface of the post bracket on the side using two short bolts. with the lock knob. Ensure the table is not catching the sanding belt, then tighten the lock knob to secure the table. 25 | Page 6305 Sander OLIVERMACHINERY.NET...
- Page 26 Running this sander without a dust collection system, or using a dust collection system with inadequate suction may damage the machine and cause other IMPORTANT hazardous situations. Check your dust collection system regularly to make sure it is not jammed or filled up. 26 | Page Oliver Machinery 6305 Sander...
- Page 27 8. Turn off the sander to complete the test run. Congratulations! You have completed the test run. If you discover any issues from the tests, refer to the troubleshooting section and maintenance section to diagnose issues and make adjustments. 27 | Page 6305 Sander OLIVERMACHINERY.NET...
- Page 28 Always wear high-quality dust masks when operating the sander. Clear the Work Area Before turning on the sander, make sure the sander table is free of debris, and the workpiece is not engaging the sanding belt. 28 | Page Oliver Machinery 6305 Sander...
- Page 29 Position the table at least 1/16” above the bottom edge of the sanding belt. Doing so prevents materials or body parts from getting caught between the table and WARNING the belt, which can cause serious injury. 29 | Page 6305 Sander OLIVERMACHINERY.NET...
- Page 30 Doing so increases the risk of the and turn on the dust collection system. workpiece pulling away from the operator, 6. Turn on the sander. which may cause serious injuries and machine damage. 30 | Page Oliver Machinery 6305 Sander...
- Page 31 8. Remain in full control of the workpiece and keep hands away from the abrasive surface. Use the fence and stop bracket to provide additional support when applicable. 31 | Page 6305 Sander OLIVERMACHINERY.NET...
- Page 32 Keeping all belt guards installed at most times improves IMPORTANT dust collection effectiveness for edge/horizontal sanding, and reduces the risk of accidental body contact with the sanding surface and moving parts. 32 | Page Oliver Machinery 6305 Sander...
- Page 33 Accessories Touchup Paint Keeping all painted surfaces in good condition not only makes your machine look nice but also keeps rusts away. Oliver Machinery has pre-mixed spray paint available in Oliver-Blue for purchase. Accessories are available on our website: OLIVERMACHINERY.NET To order by phone, please call us at 1-800-559-5065.
- Page 34 Monthly Disconnect the machine from the power source before any maintenance work is performed. After servicing the sander, remove all tools before restarting the WARNING machine. Failure to comply can cause serious injury! 34 | Page Oliver Machinery 6305 Sander...
- Page 35 When the sanding belt is properly tensioned, it should not slip off from the drums. 10. Reinstall the belt guards and the stop 6. Gently slide the sanding belt off the drums. bracket. Tighten all lock knobs. 35 | Page 6305 Sander OLIVERMACHINERY.NET...
- Page 36 4. Adjust belt tracking by rotating the bolt 1/4 turn at a time. Tighten the lock nut and turn on the machine to verify the adjustment. 5. Repeat steps 1-4 as needed. 36 | Page Oliver Machinery 6305 Sander...
- Page 37 Move tension lever to “Tight” position. tension. Replace tension spring as needed. Worn/broken sanding Replace sanding belt. belt. Improper Check, adjust, and tighten motor/component motor/component mounting. mounting. Motor bearing issue. Contact customer service for further assistance. 37 | Page 6305 Sander OLIVERMACHINERY.NET...
- Page 38 Do not fold or smash the sanding belt as it may disintegrate the bonding material on the belt. 38 | Page Oliver Machinery 6305 Sander...
- Page 39 Deenergize the electrical circuit before touching any enclosed, electrified parts. Touching an electrified part WILL result in serious personal injury or death. DANGER All electrical work must be done by a qualified electrician and must meet the electrical code in your area. WARNING 39 | Page 6305 Sander OLIVERMACHINERY.NET...
- Page 40 Parts List Table and Base 40 | Page Oliver Machinery 6305 Sander...
- Page 41 Stand 41 | Page 6305 Sander OLIVERMACHINERY.NET...
- Page 42 Motor and Sander Assembly 42 | Page Oliver Machinery 6305 Sander...
- Page 43 End Table 43 | Page 6305 Sander OLIVERMACHINERY.NET...
- Page 44 Special Screw S0111000M M10*P1.5 S0210600 Spring Washer 3/8" 20101013 Guide Block 20101014 Fence 20101015 Knob 20101016 Drive Drum 6305 MGA Miter Gauge Assembly 20102017 Guide Bar S0310306 Roll Pin S0050404 Set Screw 1/4"-20UNC*1/4"L 10104049 Locating Plate 10104050 Pointer 20102020 Position Block Sanding Belt 6"...
- Page 45 L0000000 Power Cord 20101038L Belt Cover (Long) 20101038S Belt Cover (Short) 20101002 Table Plate 20101024 Knob M8*20L 20101040 Stop Bracket 30300036 Stand Side 30300037 Stand Front/Back S0210500 Flat Washer 5/16" S0230506 Spring Washer 5/16" 45 | Page 6305 Sander OLIVERMACHINERY.NET...
- Page 46 S0020616M Hex Head Screw M6*1.0P*16 20101051 End Table 20101050 Support Rod 40101016B Mounting Bracket 20101052 Table Bracket S0020410 Cap Head Screw 1/4"-20UNC*5/8"L J0000102 Tilt Scale S0050406 Set Screw 1/4"-20UNC*3/8"L 20101048A Graphite Platen Pad 46 | Page Oliver Machinery 6305 Sander...
- Page 47 Maintenance Record Date Task Operator 47 | Page 6305 Sander OLIVERMACHINERY.NET...
- Page 48 Notes 48 | Page Oliver Machinery 6305 Sander...
- Page 49 Oliver Machinery makes every effort to assure that its equipment meets the highest possible standards of quality and durability. All products sold by Oliver Machinery are warranted to the original customer to be free from defects for a period of two (2) years on all parts excluding electronics and motors which are warranted for one (1) year from the date of shipment.
- Page 52 Oliver Machinery is always adding new Industrial Woodworking products to the line. For complete, up-to-date product information, visit us online at: WWW.OLIVERMACHINERY.NET or call toll free 1-800-559-5065 ** SAVE THIS MANUAL FOR FUTURE REFERENCES. **...