Related Manuals for Oliver 6905
Summary of Contents for Oliver 6905
- Page 1 6905 Oscillating Spindle Sander Owner’s Manual Oliver Machinery M-6905 08/2017 Copyright 2003-2017 Seattle, WA info@olivermachinery.net www.olivermachinery.net...
-
Page 2: Table Of Contents
TABLE OF CONTENTS Table of contents _____________________________________________ 1 Safety rules __________________________________________________ 2 Specifications ________________________________________________ 3 Machine legend_______________________________________________3 Machine dimension ___________________________________________ 4 Safe operating position ________________________________________ 4 Instructions for operations _____________________________________ 5 Tilting the table ______________________________________________ 5 Mounting spindle drum ________________________________________6 Selection guide for drum to table insert___________________________ 7 Maintenance of spindle sander __________________________________8 Troubleshooting ______________________________________________9... -
Page 3: Safety Rules
SAFETY RULES Read carefully before operating the machine 1. Learn the machine’s applications and limitations, as well as the specific potential hazards particular to this machine. Follow available safety instructions and safety rules carefully. 2. Keep working area clean and be sure adequate lighting is available. 3. -
Page 4: Specifications
SPECIFICATIONS 6905.001 MODEL 14-1/2" x 14-1/2" Table size (L x W) Table tilt 0~45° Spindle speed 1400rpm Oscillations per minute 29/min 15/16" Oscillation stroke 2" Dust port diameter 1/2HP/115V/1ph-only Motor MACHINE LEGEND... -
Page 5: Machine Dimension
MACHINE DIMENSION SAFE OPERATING POSITION 28" 28" 28" 28"... -
Page 6: Instructions For Operations
INSTRUCTIONS FOR OPERATIONS Select spindle that is smaller than the curve to be sanded. 2. Use an insert plate that comes closest to the spindle without touching it. 3. Make sure that spindle is properly positioned in taper sleeve socket. With the wrench provided , tighten the nut. -
Page 7: Mounting Spindle Drum
MOUNTING SPINDLE DRUM Disconnect the sander from the power source. 2. Select the proper diameter of spindle drum. 3. Clean the taper part of the spindle drum before mounting it into the spindle. 4. Use an open-end wrench to lock the spindle by holding its flat surface. At the same time, use another open-end wrench to tighten the spindle drum. -
Page 8: Selection Guide For Drum To Table Insert
SELECTION GUIDE FOR DRUM TO TABLE INSERT This machine is furnished with 5 drums. The range of drum diameter is from 1/4” to 2”. If the drum diameter is changed, the table insert needs to be changed to the proper size. The table below shows which table insert to use at 90 for various drum diameters. -
Page 9: Maintenance Of Spindle Sander
MAINTENANCE OF SPINDLE SANDER To keep spindle sander in perfect condition, clean machine and attachments at all times. Clean tapered sleeves and tapered socket before use, this will protect spindle sleeves from nicks. Check gearbox for proper oil level (Approx. 1/4 up on sight glass). We recommend that a small amount of grease be applied to table tilting screw once a month. -
Page 10: Troubleshooting
TROUBLESHOOTING TROUBLE CAUSES CORRECTION Motor does not run when 1. Switch is burned out. 1. Replace the switch. power switch is turned “ON”. 2. Connection wire is loose 2. Tighten or replace the or damaged. wire. Motor does not run at full 1. -
Page 11: Assembly Diagram
ASSEMBLY DIAGRAM... -
Page 12: Parts List
SPARE PARTS FOR 6905.001 Key no. Part no. DISCRIPTION Quantity 30201001G BASE 101a 30201001a TOP PLATE W0000000 SWITCH S1006P1 STRAIN RELIEF L000000 POWER CORD S0030622M PHILIPS HEAD SCREW 10107098 RUBBER FEET S0210403 FLAT WASHER S0011600M HEX. NUT S00303040 PHILIPS HEAD SCREW... - Page 13 SPARE PARTS FOR 6905.001 Key no. Part no. DISCRIPTION Quantity S0530028 C RING S0230506 SPRING WASHER S0210500C FLAT WASHER 30202009 OIL CAP 30202012 STORAGE PLATE FOR DRUMS 30202013 STORAGE PLATE FOR TABLE INSERTS 30202014 OIL CAP S0030304 PHILIPS HEAD SCREW...
- Page 14 SPARE PARTS FOR 6905.001 Key no. Part no. DISCRIPTION Quantity 30203019b 1/4" CLAMP 30204001 TABLE 20301002 2" LOWER FOLLOWER PLATE 20801002 1-1/2" UPPER FOLLOWER PLATE 20301044 2" UPPER FOLLOWER PLATE S0210500 FLAT WASHER S0110500L HEX. NUT 30204003 2" TABLE INSERT (OVAL) 30204004 2"...