RHINO BUMPER EVO 3D RANGER Installation Instructions Manual
Hide thumbs
Also See for BUMPER EVO 3D RANGER:
- Installation instructions manual (18 pages) ,
- Installation instruction (16 pages) ,
- Install instruction (15 pages)
Related Manuals for RHINO BUMPER EVO 3D RANGER
Summary of Contents for RHINO BUMPER EVO 3D RANGER
- Page 1 www.rhino4x4.com.au INSTALLATION INSTRUCTION MANUAL RPDE3D-FR16 You can choose a road already travelled or discover your own... I N D U S T R I A A R G E N T I N A...
- Page 2 • We do not cut the original plastic bumper, this it can be stored and reinstalled at any time. Before commencing with the installation it is important that you read and understand these installation instructions. If you need any technical adviceplease contact you closest Rhino 4x4 dealer or contact us via www.rhino4x4.com.au/contacts...
- Page 3 DO NOT use this product on any other vehicle make or model, other than those specified. DO NOT remove the warning labels or Rhino 4x4 logo from the VFPS. DO NOT modify the VFPS in any way.
- Page 4 Remove plastic facia, plastic facia retainer clips at front edge of guard, steel bumper beam and front stone shield. Remove the brackets from the wheel arch liners and the two that hold the mid lower of the facia. Plastic air deflectors can also be trimmed or removed if preferred.
- Page 5 Locate the main chassis brackets as per image. STEP 2...
- Page 6 Insert the original front chassis bolts in new bracket Insert the bracket with welded nuts into the chassis and fasten using the M10 bolts. NOTE - It is best to insert bracket, hold front hole in position by inserting screwdriver all the way through chassis, then lift the rear hole into position using screw driver through the front hole.
- Page 7 NOTE - Your fog lamps will already be installed however some times its easy to get to mounting bolts if you remove the light housings. FASTENING BOLTS Self Drilling T1 ½” EX 6 1.00 x 15 Washer D6 Nut 6 6 - 1.00 STEP 4...
- Page 8 NOTE - The next steps can be done either on or off the car Now is a good time to install Adaptive cruise Locate winch cradle radar sensor if optioned. Please turn to options page for further details on radar sensor mounting. Locate and loosely fasten wings to cradle and lower mid section FASTENING BOLTS...
- Page 9 NOTE - If optioned now is a good time to install fairleed, and winch. See winch install details in the options section. After winch install if optioned, place mid top into position and fasten using the two M10 bolts on both sides. FASTENING BOLTS AR 10 1.50 x 30 EX 6 1.00 x 15...
- Page 10 If assembled off vehicle you can now mount assembly to vehicle. Locate and loosely fasten the wing support brackets. NOTE - rear cradle bolts are inserted from under chassis Once fully in position use adjustment in chassis brackets bracket. The front two on each side are inserted from top. and wing supports to align to lower edge of lights and FASTENING BOLTS FASTENING BOLTS...
- Page 11 Locate and fasten front and then rear bash plate. FASTENING BOLTS AR 10 1.50 x 30 Countersunk screw 8 1.25 x 25 Countersunk screw 10 1.50 x 30 Threaded Plate 10 1.50 Key with Nut 8 1.25 Original Bolt STEP 8...
- Page 12 PX RANGER MK2 GRILL The Rhino4x4 Evolution 3D front winch bar for the Ranger GRILL CUT MK2 is designed to fit both the standard ranger grill and The image on the right displays where the grill is also the Ford Everest Grill. The Everest grill will fit with trimmed.
- Page 13 1. Place grill on ground front side up 2. Using a fine cutting disc on an angle grinder cut along the radius splitting it in half from one side to the other. 3. Turn the grill over ensuring the front sits on something that will not mark it.
- Page 14 NUMBER PLATE BRACKET TECH PACK KIT Locate number plate bracket to existing holes under leading edge of bar top mid as per image. FASTENING KIT EX 6 1.00 x 15 Washer D6 Nut 6 - 1.00 FASTENING KIT EX 6 1.00 x 15 After mounting radar sensor adjust to vertical.
- Page 15 WINCH ASSEMBLY Install winch as per winch manufacturers specifications. OPTIONAL...
- Page 16 Once you have finished bar install ensure fog lamps, parking sensors and radar sensor are plugged in. NOTE - Ensure you road test vehicle to confirm operation of radar sensor. Adjustment of radar sensor angle may be required if error on dash. Great Job! FINISH...
- Page 17 with a couple of rubber joints optional optional optional FASTENING BOLTS m Grill Bracket AR 10-1.5 x 20 Washer D10 AR 6-1.00 x 20 Washer D8 Nut 10-1.5 AR 8-1.25 x 30 ¾ x Set Screw Allen Button 8-1.25 x 20 p1 Threaded plate 10-1.5 EXAG 6-100 x 15 Plate with nut 8-1.25...
- Page 18 www.rhino4x4.com.au Factory 2 / 25 Progress Street Mornington VIC 3931 Australia sales@rhino4x4.com.au TOUGH NEVER LOOKED SO GOOD...
Need help?
Do you have a question about the BUMPER EVO 3D RANGER and is the answer not in the manual?
Questions and answers