Download Print this page

RHINO BUMPER evO 3D Installation Instruction

For holden colorado 2017+
Hide thumbs Also See for BUMPER evO 3D:

Advertisement

Quick Links

INSTALLATION INSTRUCTION
HOLDEN
COLORADO
2017+
102116 - 025
BUMPER evO 3D

Advertisement

loading
Need help?

Need help?

Do you have a question about the BUMPER evO 3D and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for RHINO BUMPER evO 3D

  • Page 1 INSTALLATION INSTRUCTION HOLDEN COLORADO 2017+ 102116 - 025 BUMPER evO 3D...
  • Page 2 Before commencing with the installation it is important that you read DO NOT remove the warning and understand these installation instructions. If you need any technical adviceplease contact you closest Rhino 4x4 dealer labels or Rhino 4x4 logo from or contact us via www.rhino4x4.com.au/contacts the VFPS.
  • Page 3 STEP 1 REMOVE ORIGINAL FACIA a. Remove facia by removing screws on top of grill and screws around wheel arch. Then remove bolts from under front of facia. Start the removal by pulling at the clips at wheel arch side and continue through to under light.
  • Page 4 STEP 2 PRE INSTALL PREP Remove plastic facia clips by Trim the lugs drilling out off lower light pop rivets with multi and removing tool ensuring nuts. minimal dust entry. Remove bracket and dispose Fill holes with Sikaflex ensuring water tight. NOTE: Trim off Its vital the...
  • Page 5 STEP 3 PRE INSTALL PREP OPTIONAL Mask up light Trim plastic and guard as at line both per photo. sides of car Apply black and dispose of paint to under lower part. File light and guard or sand cut for edge clean edge.
  • Page 6 STEP 4 CHASSIS BRACKETS Place main chassis brackets into position on front of chassis and loostly re fit original bolts Place side chassis brackets into position and loosly fit 2x original bolts in lower face and 2x supplied M10 bolts, nuts and washers in side.
  • Page 7 STEP 5 WINCH CRADLE Place winch cradle on chassis brackets and loosly fix the 6 M12 bolts, nuts and washers. NOTE: Tighten only enough to reduce slack but not enough to lock up part. This will be done later once all panels in place.
  • Page 8: Fog Lights

    STEP 6 FOG LIGHTS Screw self tapping Your Evolution 3D bumper will come with Bolt M6 the lights pre installed in the housings for your convenience. If however you need to Washer M6 assemble please see the above details on how to do so.
  • Page 9 STEP 7 WINGS Apply rubber seal to this edge of wing only. Position wing to winch cradle and fasten using supplied M10 bolts, Nuts, and washers. Tighten just before movement of mid is restricted.
  • Page 10 STEP 8 UPPER AND LOWER Insert top mid and fasten using 4 M10 bolts, washers and nuts. Tighten just before movement of mid is restricted. Insert Lower mid and fasten using 2 M10 bolts, washers and nuts. Tighten just before movement of mid is restricted.
  • Page 11 STEP 9 WING ALIGNMENT AND LOCKING UP NOTE: This step is vital to your end result. Spend a little time to ensure you dont rush this step. It will ensure the end result looks great and aligns well. With all bolts done up to just before locking parts, align wing so that you acheive a nice even vertical gap of about 15-20mm along guard.
  • Page 12: Number Plate

    STEP 10 SENSORS AND NUMBER PLATE SENSORS OPTIONAL: If your vehicle is equiped with front parking sensors, remove sensors and harness from original bumper. Then cut the retaining clips from original bumper using a sharp blade either side of plastic weld as per photo.
  • Page 13: Optional Winch

    STEP 11 OPTIONAL WINCH WINCH Our bar is compatible with the Rhino4x4 Tough 12500 and 9500 Lbs winches. If optioned they will bolt directly into the winch cradle with no modifications T O U G H P R E M I U M W I N C H E S YEARS WARRANTY Mount relay box to winch and connect...
  • Page 14 STEP 12 BASH PLATE Locate front bash plate and loosly fix using the small counter sunk bolts and welded nut spanners on rear. Hold up rear against chassis and drill rear holes through the holes as per image. Fasten rear using supplied large counter sunk bolts and threaded plates.
  • Page 15 STEP 13 GRILL INSTALL The original grill is removed from the facia and re installed. Before it is re- installed black sections at rear need to be trimmed as per image. A section of the feet that retain the lower grill is retained and re used to secure in place.
  • Page 16 TOUGH NEVER LOOKED SO GOOD If the customer or nominated agent chooses to self-install, or have the product(s) installed including any modification at a non-accredited Rhino4x4 Re-Seller/Workshop, Rhino4x4 is not 2 / 25 Progress Street responsible or liable for any loss suffered, including indirect or consequential damages caused to the vehicle during and arising from or in relation to such installation Mornington VIC 3931 Australia RHINO4X4.COM.AU Note: Ensure no pipes or cables contact the bar or moving parts.