Geemarc Wake 'n' Shake Voyager V2 - Alarm Clock User Manual

DESCRIPTION OF THE PRODUCT

BATTERY INSTALLATION

Your clock requires 1 x AAA and 2 x AA alkaline batteries (included) to operate.

1. Place your unit face down on a flat surface.
2. Press the latch and remove the battery cover at the back of your unit.
3. Insert 1 x AAA and 2 x AA new alkaline batteries into the battery compartment by observing the correct "+" and "- "polarity.
4. Replace the battery cover.

TO SET TIME AND THE SNOOZE DURATION

1. Press and hold SET, the hour digits "0" flash. Press TEST/ or to set the time in hours (hold TEST/ or to advance rapidly).
2. Press SET again, the minute digits "00" flash. Press TEST/ or to set the time in minutes. (hold TEST/ or to advance rapidly).
3. Press SET again, the display shows "24Hr" and flashes. Press TEST/ or to select "12Hr" or "24Hr" time format. There has AM icon to indicate the morning time and PM icon to indicate the afternoon time.
4. Press SET again, the display shows "05" and flashes. Press TEST/ or to select your snooze time from 5 to 60 minutes.
5. Press SET again or if no key pressed for approx. 10 seconds to exit the setting mode.

TO SET THE ALARM

default at 6:00 AM

1. Press and hold AL SET / SELECT, the AL appear and the alarm's hour digits' flash. Press TEST/ or to set the alarm in hours. (hold TEST/ or to advance rapidly).
2. Press AL SET / SELECT once again, the alarm's minute digits' flash. Press TEST/ or to set the alarm in minutes. (hold TEST/ or to advance rapidly).
3. Press AL SET / SELECT again, and "HI" flash (vibration at HI level), press TEST/ or to select "LO" (vibration at Low level) if need.
4. Press AL SET / SELECT again, and "HI" flash (Sound at HIGH level), press TEST/ or to select "LO" (Sound at Low level) if need.
5. Press AL SET/SELECT once again or no button around 10 seconds to exit the alarm setting mode. Admist alarm setting, press SET once to exit and return to nomral time display mode.

TO SELECT THE ALARM MODE

At normal time display mode, press AL SET / SELECT one at a time to activate the alarm(s), the corresponding alarm indicator(s) on the right side of the time display will be on:

only sound alarm is activated	only shaker alarm is activated	only strobe light alarm is activated	both sound and vibration alarm are activated	both strobe light and sound alarm are activated

Press AL SET / SELECT once more to turn off all the alarms, all alarm indicators disappear.
Remark: frequent use of the vibration and flash light will quickly shorten the battery life.

TO STOP AND RESET THE ALARM TO COME ON THE NEXT DAY

When alarm is sounding, the corresponding alarm indicator flashes. Press AL STOP once to stop the alarm and reset it to come on the following day. After that, the corresponding alarm indicator stays on the display.

TO USE SNOOZE

When alarm is sounding, presses once, the alarm will be stopped temporarily and the corresponding alarm indicator keeps flashing. Alarm will come on again after the set snooze duration is over.

TO USE BACKLIGHT

Press once to active backlight 5 seconds.

TO USE FLASHLIGHT

Press and hold to active flashlight. Press and hold to de-active the flashlight.

TEST MODE

Press and hold TEST/ Button, strobe light flashing, shaker vibrating and buzzer sounding for 5 seconds and then stops.

LOW BATTERY ALERT

When the battery level becomes low, an low battery icon will apear on the upper middle of the LCD. Repalce batteries with new alkaline batteries.
Remark: frequent use of the vibration alarm will quickly shorten the battery life.

TROUBLE SHOOTING

If your clock displays irrelevant time or does not function properly, which may be caused by electro-static discharge or other interference, open the battery cover, take out the batteries and reinstall them by observing the correct +/- polarity. Your clock will be reset to default settings and you need to set it again.
Low battery level will decrease the vibration and the alarm sound. Once this happens, replace batteries with new ones.

CARE OF YOUR PRODUCT

1. Place your clock on a stable surface, away from sources of direct sunlight or excessive heat or moisture.
2. Protect your furniture when placing your units on a natural wood and lacquered finish by using a cloth or protective material between it and the furniture.
3. Clean your unit with a soft cloth moistened only with mild soap and water. Stronger agents such as Benzene, thinner or similar materials can damage the surface of the unit. Make sure the unit is unplugged before cleaning.
4. If the unit is not to be used for a prolonged period, such as a month or longer, remove the batteries to prevent possible corrosion. Should the battery compartment become corroded or dirty, clean the compartment thoroughly and replace the batteries.

SPECIFICATIONS

Documents / Resources

Download manual

Here you can download full pdf version of manual, it may contain additional safety instructions, warranty information, FCC rules, etc.

Download Geemarc Wake 'n' Shake Voyager V2 - Alarm Clock User Manual