Hunter 99371 Manual

CEILING FAN REMOTE CONTROL
Model 99371
HUNTER FAN COMPANY CONTROL LIMITED WARRANTY
The Hunter Fan Company makes the following limited warranty to the original purchaser
of the Control ("Control"): Your Control is warranted to be free from defects in material and
workmanship for a period of one year from the date of sale. If the Control malfunctions
or fails within the warranty period due to a defect in material or workmanship we will
replace it free of charge. IF THE ORIGINAL PURCHASER CEASES TO OWN THE CONTROL,
THIS WARRANTY AND ANY IMPLIED WARRANTY, INCLUDING BUT NOT LIMITED TO ANY
IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE,
ARE VOIDED. THIS WARRANTY IS IN LIEU OF ALL OTHER EXPRESS WARRANTIES. THE
DURATION OF ANY IMPLIED WARRANTY, INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED
WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, IN
RESPECT TO ANY CONTROL, IS EXPRESSLY LIMITED TO THE PERIOD OF THE EXPRESS
WARRANTY SET FORTH ABOVE FOR SUCH CONTROL. This warranty excludes malfunctions
or failures which were caused by repairs by persons not authorized by us, mishandling,
improper installation, modifications, or damage to the Control while in your possession, or
unreasonable use. This warranty does not apply to batteries or to deterioration or damage
to the product caused by the use of faulty batteries. To obtain a replacement, return your
Control postage prepaid along with proof of purchase to Hunter Fan Company Service
Department at 7130 Goodlett Farms Pkwy., Memphis, TN 38016. IN NO EVENT SHALL
HUNTER FAN COMPANY BE LIABLE FOR CONSEQUENTIAL OR INCIDENTAL DAMAGES.
SOME STATES DO NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY
LASTS OR THE EXCLUSION OR LIMITATIONS OF INCIDENTAL OR CONSEQUENTIAL
DAMAGES SO THE ABOVE LIMITATIONS OR EXCLUSIONS MAY NOT APPLY TO YOU. THIS
WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS AND YOU MAY ALSO HAVE OTHER
RIGHTS WHICH VARY FROM STATE TO STATE.
Read and Save These Instructions
This product conforms to UL Standard 1917.
WARNINGS
This device complies with part 15 of the FCC Rules. Operation is
subject to the following two conditions: (1) this device may not cause
harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
This device complies with RSS-210 of Industry Canada. Operation
is subject to the following two conditions: (1) this device may not
cause interference, and (2) this device must accept any interference,
including interference that may cause undesired operation of the
device.
This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However there is no
guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one
or more of the following measures: Reorient or relocate the receiving
antenna, Increase the separation between the equipment and
receiver, Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected. Consult the dealer or
an experienced radio/TV technician for help. Note: Any changes or
modifications to the transmitter or receiver not expressly approved by
Hunter Fan Company may void one's authority to operate this remote
control.
If you are installing multiple remote-controlled fans
on the same circuit breaker,
you may need to perform a few extra steps to prevent interference or faulty
operation of your remote controls.
Go to www.HunterFan.com/FAQs and click "How do I properly install multiple
remote-controlled fans?" for more information.
Installation
1
Turning off the power
Before installation, use the pull chains to set
the fan speed to HIGH and the light to ON.
Ensure the power is OFF at the outlet box and
wall switch location before proceeding with
installation.
2
Removing the canopy
Remove the canopy. If uncertain how to remove
it, reference the fan's owner's manual. With
wiring exposed, it may be helpful to note existing
wire connections or take a digital photo for
reference. Remove the wire connectors that
connect the wires from the outlet box to the fan,
leaving the grounding wires connected.
3
Installing the receiver
Choose the hanging system that most closely
resembles the one used by your fan, and
install the receiver and wire as directed.
You may have installation issues if the fan is
installed on an angled ceiling. For assistance,
call 1-888-830-1326.
Receiver
Receiver Ceiling
Plate
OR OR OR
Receiver
Canopy
Canopy
Canopy
Note: Some fans may have considerable excess lead wire. For easier canopy
installation, cut the excess wire, leaving a minimum of 8" remaining. Re-strip the fan lead
wires 1/2". Place remaining excess wire into the ceiling electrical box. The bracket and
fan must remain properly grounded.
4
Wiring the receiver to the fan
Using the orange wire connectors, connect
the blue wire from the receiver to the blue
wire (or possibly black with white stripe wire)
from the fan. Connect the yellow wire from the
receiver to the black wire from the fan.
Note: If you are uncertain about wire colors or connections, please contact a qualified electrician.
blue
blue
yellow
black
To avoid possible electrical shock, before installing or servicing your fan, disconnect the power by turning
off the circuit breakers to the outlet box and associated wall switch location. If you cannot lock the circuit
breakers in the off position, securely fasten a prominent warning device, such as a tag, to the service panel.
5
Wiring the receiver and fan to the ceiling
Using the orange wire connectors, connect the
black wire (ungrounded) from the ceiling to the
black wire from the receiver. Connect the white
wire (grounded) from the ceiling to both the
white wire from the receiver and the white wire
from the fan.
OFF
AFTER ALL WIRES ARE CONNECTED and
secured with wire connectors, re-install the
canopy.
black black (ungrounded)
white
white white (grounded)
Turn the splices upward and push them carefully back through the hanger bracket into the outlet box.
Spread the wires apart, with the grounded wires on one side of the outlet box and the ungrounded wires on
Cable Tie
the other side of the outlet box.
Ceiling
Bracket
A
Fan Body
6
Installing the battery
To access the battery compartment, remove
the small Phillips head screw that secures the
battery door to the remote control.
Replace the used battery with a CR2032
battery when necessary. The battery should
be installed with the positive (+) side up.
7
Turning on the power
IMPORTANT
Use the pull-chain switch on the fan to set
the fan speed to the HIGH position before
operation.
8
Reference the included remote function card for
information on how to use your control!
Cradle Installation
Remove the cradle from
the cradle bracket.
You have two options to install the included remote control
cradle to the wall. Choose which path works best for you.
Option 1
Using screws
Choose your cradle installation location.
If you are installing into drywall, drill two 9/64
width holes using the cradle bracket as a guide.
Gently hammer the included drywall anchors into
the pre-drilled holes.
Install the cradle bracket to the wall with the
included screws.
Option 2
Using Adhesive Strip
Battery
Door
Phillips
Head
Screw
Apply the adhesive sticker to the back of cradle
bracket per the instructions on the adhesive sticker.
ON
Press the cradle bracket against the wall and
hold firmly for 30 seconds.
Slide the cradle onto the mounted bracket.
M0123 • 07/11/16 • © 2016 Hunter Fan Company