Table of Contents
Advertisement
Quick Links
60in TITAN
Model No. 76601—Serial No. 400000000 and Up
Model No. 76602—Serial No. 400000000 and Up
Setup
Loose Parts
Use the chart below to verify that all parts have been shipped.
Procedure
1
2
3
4
5
6
7
8
9
10
11
Note:
Determine the left and right sides of the machine from the normal operating position.
© 2021—The Toro® Company
8111 Lyndale Avenue South
Bloomington, MN 55420
®
MAX Riding Mower
Description
No parts required
No parts required
No parts required
No parts required
No parts required
No parts required
No parts required
No parts required
No parts required
No parts required
Operator's Manual
Engine owner's manual
Operator-training material
Key
Registration card
Register at www.Toro.com.
Form No. 3449-600 Rev A
Qty.
–
Remove the machine from the crate.
–
Add fuel to the machine.
–
Check the engine-oil level.
–
Check the hydraulic-fluid level.
–
Check the tire pressure.
–
Charge the battery.
Raise the rollover-protection system
–
(ROPS).
–
Check the grass deflector.
–
Check the mower adjustment.
Check the machine before delivery to
–
the customer (all machines).
1
1
Deliver the machine to the customer (all
1
machines).
2
1
Original Instructions (EN)
Printed in the USA
All Rights Reserved
Setup Instructions
Use
*3449-600*
Advertisement
Table of Contents
Related Manuals for Toro 76602
Summary of Contents for Toro 76602
- Page 1 Form No. 3449-600 Rev A 60in TITAN ® MAX Riding Mower Model No. 76601—Serial No. 400000000 and Up Model No. 76602—Serial No. 400000000 and Up Setup Instructions Setup Loose Parts Use the chart below to verify that all parts have been shipped.
-
Page 2: Removing The Machine From The Crate
If removing the machine from a metal crate, refer to This machine is shipped filled with hydraulic fluid in the Dealer/Distributor Portal for further information. the reservoirs. Check the expansion tank; if necessary, add Toro ® HYPR-OIL ™ 500 hydraulic fluid, as recommended in... -
Page 3: Checking The Tire Pressure
Checking the Tire Pressure Raising the Rollover-Protection System No Parts Required (ROPS) Procedure No Parts Required Pressure: 13 psi (90 kPa) Note: Check the tire pressure before starting the Procedure machine. Refer to your Operator’s Manual for the Important: Always use the seat belt with the roll correct tire type and procedure. -
Page 4: Checking The Mower Adjustment
Checking the Grass Deflector No Parts Required Procedure If there are plastic ties holding the grass deflector up, remove them and lower the deflector into place. WARNING An uncovered discharge opening could allow the machine to throw objects toward you or bystanders, resulting in serious injury or death. - Page 5 Checking the Machine Before Delivery to the Customer (All Machines) No Parts Required Procedure Before delivering the machine to the customer, ensure that you have performed the procedures listed in the following table and initial each when finished. Refer to the Operator's Manual for instructions on performing these procedures.
- Page 6 Delivering the Machine to the Customer (All Machines) Parts needed for this procedure: Operator's Manual Engine owner's manual Operator-training material Registration card Procedure At delivery, fill in the model and serial number, complete the items listed in the following table, and initial each when finished.
- Page 7 Make sure that the customer receives the Operator's Manual, engine owner's manual, Setup Instructions, and operator training material. Make sure the customer knows that the Parts Catalog is available at www.Toro.com. Assist the customer in loading the machine. Note: When you, the dealer representative, have finished delivering the machine to the customer, sign and date in the space provide below and keep a copy of this page for dealer records.