Maintenance, Cleaning & Storage - DeWalt DXFP841001 Instruction Manual

English
WARNING: It is the responsibility of the users to ensure that they read, understand, and follow all instructions
and are trained in the care and use of this device. Training should be repeated periodically and any time there
is a change of components within the system. Training must be conducted without exposing the trainee to a
fall hazard
WARNING: Do not attempt to disassemble the unit or make repairs to the equipment. Send the equipment back
to the manufacturer, or persons or entities authorized in writing by the manufacturer to make repairs to the
equipment.
WARNING:
Cleaning after use is important for maintaining the safety and life of the equipment.
Use only mild soap and water, and hang to dry in shade.
MAINTENANCE, CLEANING & STORAGE:
• Repairs to equipment can be made only by
a DEWALT representative or person or entity
D WALT D WALT
authorized by . Contact for
E E
maintenance and repair. Cleanse the equipment
of all dirt, corrosives, and contaminants.
• Store the anchorage connector component in a
cool, dry and clean place out of direct sunlight.
Avoid areas where heat, moisture, light, oil, and
chemicals or their vapors or other degrading
elements may be present. Equipment which is
damaged or in need of maintenance should not
be stored in the same area as usable equipment.
Heavily soiled, wet, or otherwise contaminated
equipment should be properly maintained (e.g.
dried and cleaned) prior to storage.
• Prior to using equipment which has been stored
for long periods of time, a Formal Inspection
should be performed by a Competent person.
TRAINING:
• As Per OSHA: Anchorages used for attachment of
personal fall arrest systems shall be independent
of any anchorage being used to support or
suspend platforms and capable of supporting
at least 5,000 lbs. (23kN) per user attached,
or be designed, installed and used as part of a
complete PFAS which maintains a safety factor
of at least two, and is under the supervision of a
qualified person.
14
NEVER use bleach or bleach solutions
to clean anchor.
LIFESPAN:
• The lifespan of any component of a personal fall
arrest system (PFAS) is dependent upon its level
of use, the environment in which it is used and
how it is maintained. Any part of the PFAS that
passes daily inspection by an Authorized person
or periodic (annual or semiannual) inspection
by a Competent person, can stay in use. Once it
fails visual inspection it must be removed from
service.
DISCLAIMER:
• Prior to use, the end user, must read and
understand the manufacturer's instructions
supplied with this product at the time of
shipment and seek training from their
employer's trained personnel on the proper
usage of the product. Manufacturer is not liable
or responsible for any loss, damage or injury
caused or incurred by any person on grounds of
improper usage or installation of this product.
TWO-YEAR WARRANTY – FALL PROTECTION PRODUCTS:
THE FOLLOWING IS MADE IN LIEU OF ALL WARRANTIES OR CONDITIONS, EXPRESS OR IMPLIED, INCLUDING THE
IMPLIED WARRANTIES OR CONDITIONS OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.
THIS WARRANTY IS EXPRESSLY LIMITED TO ORIGINAL RETAIL BUYERS OF DFP SAFETY CORPORATION FALL PROTECTION
PRODUCTS OR PARTS. THIS WARRANTY IS NOT ASSIGNABLE OR TRANSFERABLE. DFP SAFETY CORPORATION MAKES
NO WARRANTY TO ANYONE ELSE, INCLUDING OTHER PURCHASERS AND/OR USERS, AND NONE SHALL BE IMPLIED.
Except as otherwise provided in this warranty, DFP Safety Corporation Fall Protection Products are warranted against
defects in materials and workmanship for two years from the date of purchase.
LIMITED REMEDY: The sole and exclusive remedy for any DFP Safety Corporation product found to be defective in
materials and workmanship is repair or replacement, at the sole option of DFP Safety Corporation, or its authorized
warranty service providers. If this exclusive remedy is deemed to have failed of its essential purpose, DFP Safety
Corporation's liability shall not exceed the purchase price of the DFP Safety Corporation product.
LIMITATION OF LIABILITY: In no event will DFP Safety Corporation be liable for any direct, indirect, special, incidental,
punitive or consequential damages (including lost profit) whether based on warranty, contract, tort, or any other legal
theory.
This warranty does not cover any DFP Safety Corporation product that has been abused, altered, worn out,
contaminated, rusted, excessively heated, ground, damaged due to improper loading, used for a purpose other than
that for which it was intended, or used in a manner inconsistent with DFP Safety Corporation's instructions regarding
use.
The existence of a defect in materials or workmanship shall be determined by DFP Safety Corporation in
accordance with procedures established by DFP Safety Corporation. No one is authorized to make any statement or
representation altering the terms of this warranty.
ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR
A PARTICULAR PURPOSE ARE DISCLAIMED. THERE ARE NO WARRANTIES THAT EXTEND BEYOND THE FACE OF THIS
DOCUMENT.
This writing supersedes all prior oral or written agreements or representations and excludes all warranties not set
forth herein.
English
15