DeWalt DXFP841001 Instruction Manual page 7

English
Steel Roof Anchor (DXFP846000)
• Place Anchor at selected installation location.
• Install all (6) provided 1/4" x 3" (6.35mm x
76.2mm) lag screws OR (12) provided 16d nails
in fastener installation holes.
• Screws must be installed in bottom, middle, and
top fastener installation holes on each side of
Anchor.
• Nails must be installed in all available fastener
installation holes. Fasteners must be fully
embedded in substrate.
• NEVER use Anchor in permanent installations.
Anchor may be removed and reinstalled in
multiple installation locations. ALWAYS inspect
the Anchor prior to each installation. ALWAYS
use new fasteners for each new installation.
• Attach complete and compatible PFAS to Anchor
O-ring. NEVER make attachments to any other
part of Anchor.
* This Anchor may be used in combination
with a Horizontal Lifeline (HLL). All set-up,
installation, and use of HLLs must be done
under the supervision of a Qualified Person.
Beam Anchor (DXFP846001)
• Beam anchor is intended to be installed on
flanges of beam from 3.54" - 13.4" (90mm -
340mm) width.
• Push the latch and adjust the movable jaw
enough to allow the clamping jaws to fit over
the flange of beam and release the latch to lock
its position.
• Use the D-ring as connecting point.
Beam Anchor (DXFP846011)
• Beam anchor is intended to be installed on
flanges of beam from 2.95" - 5.90" (75mm -
150mm) width.
• Push the latch and adjust the movable jaw
enough to allow the clamping jaws to fit over
the flange of beam and release the latch to lock
its position.
• Use the D-ring as connecting point.
10
Beam Anchor Trolley (DXFP846101)
Beam Anchor Trolley is intended to be installed on
flanges of beam from 9.84" - 3.14" (250mm-80mm)
width.
•
•
Product Model
DXFP841001
DXFP841002
DXFP843001
DXFP843002
DXFP844001
DXFP845001
Direction of
Load
DXFP846000
DXFP846001
DXFP846011
DXFP846101
Direction of
Load
Push the latch and adjust the movable jaw
enough to allow the clamping jaws to fit over
the flange of beam and release the latch to lock
its position.
Use the D-ring as connecting point.
Minimum
Description Breaking
System
Steel Anchor 5000 lbs / 23 kN
Steel Anchor 5000 lbs / 23 kN
D-Ring Two Hole
5000 lbs / 23 kN
Anchor
D-Ring Two Hole
5000 lbs / 23 kN
Anchor
Steel Point Anchor 5000 lbs / 23 kN
Girder Anchor 5000 lbs / 23 kN
Beam Anchor 5000 lbs / 23 kN
Beam Anchor 5000 lbs / 23 kN
Beam Anchor
5000 lbs / 23 kN
Trolley
Steel Anchor 5000 lbs / 23 kN
English
Direction of
Load
Material of
Complying Norm
Construction
Galvanized Steel ANSI Z359.18-2017 Type A
Galvanized Steel ANSI Z359.18-2017 Type A
Galvanized Steel ANSI Z359.18-2017 Type A
Stainless Steel with
ANSI Z359.18-2017 Type A
Galvanized Dring
Galvanized Steel ANSI Z359.18-2017 Type A
Stainless Steel with
Galvanized Steel ANSI Z359.18-2017 Type A
Anchorage Eye
Aluminium Alloy &
ANSI Z359.18-2017 Type A
Brass
Aluminium Alloy &
ANSI Z359.18-2017 Type A
Brass
Aluminium Alloy &
ANSI Z359.18-2017 Type A
Stainless Steel
High Strength Alloy
ANSI Z359.18-2017 Type A
Steel
11