Kimberly-Clark PROFESSIONAL 47604 Quick Start Manual

Kimberly-Clark PROFESSIONAL 47604 Quick Start Manual

Automatic soap and sanitizer dispenser counter mount

Advertisement

Automatic Soap and Sanitizer
Dispenser Counter Mount
Soap Discharge Head
with Signal Cable
Dispenser Code# 47604
Battery
Optional Hex Nut
Battery
Compartment
Compartment
Installation Tool
Base with
Cover
(P/N 774103)
Power Cable
Lock Washer
Nut
Motor Module
Use of this Dispenser
Not recommended for outdoor installation or in wet environments. Do not attempt to clean the dispenser
with a water jet. Follow the installation and usage instruction. Only use genuine Kimberly-Clark Professional
product refills intended for the specific model. The dispenser can be cleaned using a damp cloth and
detergent, do not use abrasive cleaning products.
These instructions are available at www.kcprofessional.com.
General Safety Information
This dispenser can be used by children over the age of 8 years old and persons with reduced physical,
sensory or mental capabilities, or lack of experience and knowledge, provided they have been given
supervision or instruction concerning use of the dispenser by a person responsible for their safety. Access to
the service area is restricted to persons who have knowledge and practical experience of the dispenser, in
particular as far as safety and hygiene are concerned.
This dispenser is not a toy and shall not be used by children as such. Children shall not perform cleaning or
user maintenance of this dispenser. High-risk individuals are not expected to use this dispenser safely unless
continuous supervision is given
Need more information?
These instructions and additional resources are
Form 033955 • 4/2022
available at www.kcprofessional.com.

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the 47604 and is the answer not in the manual?

Questions and answers

darin martin
February 3, 2025

what are the best settings for the dispenser

Subscribe to Our Youtube Channel

Summary of Contents for Kimberly-Clark PROFESSIONAL 47604

  • Page 1 Not recommended for outdoor installation or in wet environments. Do not attempt to clean the dispenser with a water jet. Follow the installation and usage instruction. Only use genuine Kimberly-Clark Professional product refills intended for the specific model. The dispenser can be cleaned using a damp cloth and detergent, do not use abrasive cleaning products.
  • Page 2: Dispenser Installation

    Dispenser Installation Materials Required: • Phillips Bit • Cutting Fluid • 1” Diameter Hole Saw (Diamond Bit for Granite or Stone) • Adjustable Wrench • Clear Silicone Caulk • Magic Marker Note: If drilling of the counter top is 1. If a 1” hole already exists required, be sure to use an approved KC on the countertop, go to Installer or other trained professional.
  • Page 3 Dispenser Installation 6. Insert the signal cable and threaded shaft of the soap discharge head through the hole in the countertop. 7. Finalize the position of the soap discharge head and then press down firmly to secure it. 8. Position the lock washer and nut on the bottom of the threaded shaft.
  • Page 4 Dispenser Installation 12. While holding the motor module in place, slide the clip on the motor module forward to lock the motor module to the threaded shaft. 13. Remove the protective cap on the end of the signal cable. 14. Orient the plug on the end of the signal cable so it is properly keyed with the connector on the motor module.
  • Page 5: Battery Installation

    Battery Installation 1. Load four (4) batteries into the battery compartment cover ensuring polarity is correct. 2. Orient the battery compartment cover with the extension tab on top and install it into the battery compartment base. 3. Tighten the two screws on the battery compartment cover until secure.
  • Page 6: Power Adapter

    Power Adapter 1. If the dispenser is running on battery power, remove the battery power connector while holding the motor module. 2. Orient the plug on the end of the power adapter so it’s properly keyed with the connector on the on the motor module. While holding the motor module push the plug into the connector until fully seated.
  • Page 7 Load New Bottle 1. Slip the straw into the underside of the motor module. 2. Push the refill bottle up into the motor module until both snaps on the bottle are secure. Snap 1 Snap 2 3. Prime the pump by placing one hand under the soap discharge head in order to break the opposing IR beam to activate the motor.
  • Page 8 Notifications Power On Soap Bottle Installed Whenever power is connected Whenever a soap bottle is to the dispenser both the red and yellow LEDs on the soap properly installed, both the red and yellow LEDs on discharge head will flash to SECONDS SECONDS indicate the software version.
  • Page 9 Legal ®/™ Trademarks of Kimberly-Clark Worldwide, Inc. or its affiliates. © KCWW ®/™ Marques de commerce de Kimberly-Clark Worldwide, Inc. ou de ses filiales. © KCWW Made in CHINA / Fabriqué en CHINA / Fabricado en los CHINA Distributed in the U.S. by Kimberly-Clark Global Sales, LLC, Roswell, GA 30076-2199 Distributed in Canada by Kimberly-Clark Inc., Mississauga, Ontario L5B 3Y5 Americans with Disabilities Act (For use in U.S.

Table of Contents