Advertisement
Thank you for choosing a SYD Powered Speaker, designed by Kanto in Canada. SYD outputs 140W Peak power for remarkably bold and clean sound. Excellent sensitivity and frequency response provide deep thumping lows and clear, scintillating highs. SYD is an amazingly flexible speaker system that can accept four input sources and connect to a subwoofer for enhanced low frequency response. Additionally, it is equipped with the latest Bluetooth technology and a USB port for charging your devices. SYD has a universal input power supply and can be used worldwide from 110V AC to 240V AC.
We recommend you read all instructions carefully before using the system and keep them for future reference. Kanto cannot be liable for damage or injury caused by incorrect setup or use of this product.
This powered speaker system was carefully tested and inspected during production, and before packaging and shipping. After unpacking, please check for any damage. It is rare that a unit is damaged during shipping, but if this happens contact your retailer immediately. You can also contact Kanto directly using one of the methods below.
Email: support@kantoliving.com
Toll Free: US & Canada: 1-888-848-2643 | UK: +44 800086999
White - Power on / Playback Mode
Yellow
Standby (solid)
Mute (flashing)
Blue
Discover Mode (flashing)
Paired (solid)
SYD's volume knob functions as an input select knob as well.
Push the knob to select an input source - it cycles through the following inputs depending on what input source was last used.
RCA AUX OPT BLUETOOTH
Push and hold the knob to enter standby or wake up from standby
Install two supplied AAA batteries in the back of your SYD remote. Remote Control functions are listed below.
SYD is designed to perform optimally positioned at least 8" from the rear wall in an average listening room. However, it may not be possible to install the speaker in this position and since rooms vary in shape, size, and furnishing, a certain amount of experimentation is necessary to determine the most suitable position.
Moving the speaker very close to the rear wall will enhance the bass frequencies but will tend to reduce soundstage depth, while moving the speaker away from the rear wall will tend to have the opposite effect. Avoid positioning the speaker close to or in the corner of a room, as this will excite undesirable room coupling in the low and middle frequencies. Room characteristics and positioning have a profound effect on the performance of the speakers, so time and effort devoted to achieving the optimum positions will be rewarded.
Ensure that the ON/OFF Switch is in the OFF position.
Follow the instructions on the ensuing pages to connect your audio sources to SYD.
Connect the power cord from SYD to the wall outlet.
ATTENTION
When connecting audio cables the ON/OFF Switch must be turned OFF. After connecting all cables, the unit can be turned ON. When the volume is high, this system can produce noise levels that could permanently damage your hearing. SYD is a self-powered speaker system. Do not connect the speaker inputs to the outputs of a stereo amplifier. Damage may occur. Use only the power cord provided with SYD.
SYD is equipped with a RCA connector to provide output signal to a powered subwoofer. Simply connect a single RCA cable from the SUB OUT connection on the SYD to the Audio Input on your subwoofer. If your subwoofer has a stereo L/R RCA input, either input will work.
We recommend the Kanto sub6 or sub8 powered subwoofer with crossover and volume controls. Most quality subwoofers offer these controls, which allow you to customize the amount of bass you will experience.
Look for details on the Kanto website at: www.kantoaudio.com
Use the appropriate audio cable to connect your audio source components to your speakers.
SYD supports data streams up to 24-bit/96 kHz resolution via Optical Toslink.
SYD features a built in Phono Pre-Amp that allows you to connect directly to a turntable.
ATTENTION
Some models of turntables include a built-in Phono Pre-Amp. If your turntable has a built in Phono Pre-Amp, DO NOT use the Phono setting. Doing so will void your warranty and could cause severe damage to your speakers.
SYD features Bluetooth 4.0 with Qualcomm® aptX™ technology and can be paired with many devices for wireless audio playback from your phone, MP3 player or tablet. Pairing is easy.
SYD features one 5V 1.0 A USB charging port on the back panel. This is a convenient power source to charge your devices.
When SYD is in Playback Mode (LED White) and Standby Mode (LED yellow), the port is active, and whatever device is connected is able to draw up to 1.0 A of power.
Sub Mute - You can disable/enable the sub output on SYD. This can be helpful in situations where you want to listen to your speakers but don't want to disturb the neighbours with sub-bass.
To mute the sub output, press and hold the Mute button for 5 seconds. You will see two LED blinks to confirm the sub output is muted. To un-mute the sub output, press and hold the Mute button again for 5 seconds. You will see one LED blink to confirm that the sub output has been un-muted. The sub output will be reactivated upon waking up from standby.
Automatic Power Up (APU) / Automatic Power Down (APD) - SYD is designed to save power when not in use. When no audio signal has been detected for 15 minutes, the SYD Amp will put itself into stand-by mode (APD). If the audio signal returns via the same input that the SYD was playing when it entered standby, the SYD will wake up and resume playing (APU). It can also be woken up manually by:
If you do not find the APU feature useful, you can disable it by pressing the Balance Reset button on the remote and holding it for 5 seconds. The Status LED will blink once to indicate that you have disabled the APU feature. To enable APU if you have disabled it, simply press and hold the Balance Reset button again for 5 seconds. The Status LED will blink twice to indicate that you have enabled APU.
If you do not find the APD feature useful, you can disable it by pressing the Bass Reset button on the remote and holding it for 5 seconds. The Status LED will blink once to indicate that you have disabled the APD feature. To enable APD if you have disabled it, simply press and hold the Bass Reset button again for 5 seconds. The Status LED will blink twice to indicate that you have enabled APD.
ATTENTION
APU/APD is always enabled when power is applied, but APU will only activate after APD has been triggered. APU will not work if the unit is manually switched to standby using the remote or control knob.
ATTENTION
APU function will not work when using the Bluetooth input.
Frequently asked questions about Kanto's SYD speaker.
None of the lights on the front panel are illuminated.
The white light on the front panel is illuminated but there's no audio playing.
Your remote is not functioning correctly.
Speakers are going into standby while listening to audio.
You are experiencing poor audio quality.
The source will not connect to Bluetooth.
You are experiencing buzzing, hissing or distortion.
There's no audio coming from an attached subwoofer.
Audio sounds different on each input.
SYD POWERED SPEAKER SYSTEM
Tweeters | 1 inch Silk Dome |
Woofers | 4 inch Kevlar® |
Amplifier Type | Class D |
Power Output | 140 Watts Peak |
Frequency Response | 60Hz – 20kHz |
Inputs | 1 x 3.5 mm stereo mini-jack AUX 1 x RCA L/R 1 x Optical (Toslink) 1 x Bluetooth® 4.0 with Qualcomm aptX |
Outputs | 1 x Subwoofer 1 x USB Charge Port 5 V 1.0A |
Standby Power Consumption | < 0.5 W |
Remote | Included |
Dimensions | W 17.5"x H 5.7" x D 6.9" (445 x 146 x 175 mm) |
NOTICE: The Bluetooth® word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. and any use of such marks by Kanto Distribution Inc. is under license.
NOTICE: Qualcomm aptX is a product of Qualcomm Technologies International, Ltd. Qualcomm is a trademark of Qualcomm Incorporated, registered in the United States and other countries, used with permission. aptX is a trademark of Qualcomm Technologies International, Ltd., registered in the United States and other countries, used with permission.
NOTICE: This appliance is labeled in accordance with European Directive 2002/96/ EC concerning waste electrical and electronic equipment (WEEE). This label indicates that this product should not be disposed of with household waste. It should be deposited at an appropriate facility to enable recovery and recycling.
Here you can download full pdf version of manual, it may contain additional safety instructions, warranty information, FCC rules, etc.
Advertisement
Thank you! Your question has been received!
Need Assistance?
Do you have a question about the SYD that isn't answered in the manual? Leave your question here.