Automower ® Connect - Husqvarna AUTOMOWER 550H Operator's Manual

2. If the indicator LED lamp does not have a green
light, do a check of the installation. Refer to
indicator lamp on the charging station on page 42
To install the charging station on page 18 .
and
3.9.2 To do the basic settings
When the product is switched on for the first time, there
are some basic settings to do before the product can
start to operate. You must for example pair the product
and the charging station, and you can choose to enable
the theft protection in GeoFence. Refer to
on page 28 . You must also pair the product and the
®
Automower Connect app to be able to change the
settings and operate the product. Refer to
Connect on page 21 .
1. Switch on the product.
Note:
The Bluetooth
for 3 minutes. If pairing has not been successful
within this time period, switch off the product.
Wait until the LED status indicator is not lit, and
then switch on the product again.
2. Enter the factory PIN code.
3. Log in to your Husqvarna account in the
®
Automower Connect app.
4. Start Bluetooth ® on your mobile device.
My mowers in the Automower
5. Select
app, and then select the plus sign (+).
6. Select model. The Automower
searches for available products within short-range
®
(Bluetooth ).
7. Select product.
8. Follow the instructions in the Automower
app.
Note:
It is only necessary to pair the Automower
Connect app and the product once.
Note:
To disconnect the Automower
the app must be fully closed down.
®
3.10 Automower Connect
The app gives 2 modes of connectivity: Long-
range cellular connectivity and Short-range Bluetooth
connectivity.
The product can connect to mobile devices that have
®
the Automower Connect app installed. Automower
Connect is a free app for your mobile device. The
®
Automower Connect app gives extended functions to
your Husqvarna product. You can:
• See the status of your product.
• Change settings to your product.
1457 - 012 - 19.01.2023
LED
GeoFence
®
Automower
®
pairing mode is active
®
Connect
®
Connect app
®
Connect
®
® Connect app,
®
®
• Get extended product information.
• Get an alarm if the product moves out of the work
area.
• See statistics of your product.
Note:
All countries do not support Automower
Connect because of regional specified cellular systems.
®
The included Automower Connect lifetime service only
applies if there is a third part sub-supplier of 2G/3G/4G
available in the operational area.
®
The Automower Connect app is preferable if you have
one or few products installed. For users with several
products we recommend you to use Husqvarna Fleet
Services ™ . Refer to Husqvarna Fleet Services
page 28 .
3.10.1 To install the Automower
app
1. Download the Automower
mobile device.
2. Sign up for a Husqvarna account in the
®
Automower Connect app.
3. An e-mail is sent to the registered e-mail address.
Follow the instructions in the e-mail in less than 24
hours to validate your account.
4. Log in to your Husqvarna account in the
®
Automower Connect app.
3.10.2 To pair Automower
the product
1. Do step 1-7 in To do the basic settings on page 21 .
2. Obey the instructions in the Automower
app.
3.10.3 Dashboard
The dashboard shows the current status of the product
both visually and in text. It is very easy to control the
product by selecting the options, for example
In the lower part of the dashboard there are shortcuts to
Schedule settings and the Map . The dashboard also
the
shows symbols according to below:
1. The battery status shows the battery state of
charge. A flash is shown over the battery symbol
when the product charges its battery. A plug is
shown over the battery symbol when the product is
in the charging station without charging.
2. Cutting height.
®
™
on
®
Connect
®
Connect app on your
®
Connect and
®
Connect
Park .
Installation - 21