1. Manuals
  2. Brands
  3. Hubbell Manuals
  4. Telephone
  5. GAI-TRONICS 277-001BH
  6. Manual

Hubbell GAI-TRONICS 277-001BH Manual

Rugged analog auto-dial telephones
Hide thumbs
Table of Contents

Advertisement

Quick Links

Rugged Analog Auto-Dial Telephones
Confidentiality Notice .....................................................................................................................1
General Information .......................................................................................................................1
Operation .........................................................................................................................................1
Installation ......................................................................................................................................2
Safety Guidelines ..................................................................................................................................... 2
Security Hardware .................................................................................................................................. 2
Model 227-001 ......................................................................................................................................... 4
Model 247-001 ......................................................................................................................................... 6
Model 257-001 ......................................................................................................................................... 8
Model 277-001 ....................................................................................................................................... 10
Flush-Mount Installation ..................................................................................................................... 10
Models 277-001BH and 277-001BHAC ............................................................................................... 12
Flush-Mount Installation ..................................................................................................................... 12
Surface-Mount Installation using the No. 238-001FS Enclosure ....................................................... 13
Programming Auto-Dial Numbers ...................................................................................................... 14
Ringdown Operation ............................................................................................................................ 14
Maintenance ..................................................................................................................................15
Service .................................................................................................................................................... 15
Preventive Maintenance for Models 277-001/-001BH/-001BHAC ................................................... 15
Cleaning .............................................................................................................................................. 15
Prevention ........................................................................................................................................... 15
Volume Control Jumper Setting .......................................................................................................... 16
Auxiliary Output ................................................................................................................................... 16
Replacement Parts and Accessories .............................................................................................17
Specifications ................................................................................................................................19
Electrical (Typical) ................................................................................................................................ 19
Environmental ....................................................................................................................................... 19
Mechanical ............................................................................................................................................. 19
Model 227-001 ....................................................................................................................................... 19
Models 247-001 and 257-001 ................................................................................................................ 19
GAI-TRONICS 3030 KUTZTOWN RD. READING, PA 19605 USA
610-777-1374  800-492-1212  Fax: 610-796-5954
V
ISIT WWW
G A I - T R O N I C S
A H U B B E L L C O M P A N Y
T
C
A B L E O F
.
-
.
GAI
TRONICS
COM FOR PRODUCT LITERATURE AND MANUALS
®
O N T E N T S
Pub. 42004-338J

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the GAI-TRONICS 277-001BH and is the answer not in the manual?

Questions and answers

Related Manuals for Hubbell GAI-TRONICS 277-001BH

Summary of Contents for Hubbell GAI-TRONICS 277-001BH

  • Page 1: Table Of Contents

    Pub. 42004-338J ® G A I - T R O N I C S A H U B B E L L C O M P A N Y Rugged Analog Auto-Dial Telephones A B L E O F O N T E N T S Confidentiality Notice ........................1 General Information ........................1 Operation ............................1...
  • Page 2 Pub. 42004-338J Rugged Analog Auto-Dial Telephones Page 2 of 2 Model 277-001 ............................20 Models 277-001BH/-001BHAC ......................20 Approvals ............................... 20 FCC Information ..........................20 IC Information (Canada) ........................20 User Instructions (USA) ........................21 User Instructions (Canada) CP-01, Issue 8, Part I: Section 14.1 ............. 21 P:\Standard IOMs - Current Release\42004 Instr.

  • Page 3: Confidentiality Notice

    Pub. 42004-338J ® G A I - T R O N I C S A H U B B E L L C O M P A N Y Rugged Analog Auto-Dial Telephones Confidentiality Notice This manual is provided solely as an installation, operation, and maintenance guide and contains sensitive business and technical information that is confidential and proprietary to GAI-Tronics.

  • Page 4: Installation

    Pub. 42004-338J Rugged Analog Auto-Dial Telephones Page 2 of 21 Installation ATTENTION —Installation should be performed by qualified personnel and only in accordance with the National Electrical Code or applicable local codes. Safety Guidelines When installing any GAI-Tronics telephone equipment, please adhere to the following guidelines to ensure the safety of all personnel: ...
  • Page 5 Pub. 42004-338J Rugged Analog Auto-Dial Telephones Page 3 of 21 Refer to Figure 1 and Figure 2. Figure 1. Bottom conduit entry installation details (RECOMMENDED for non-metallic enclosures) Figure 2. Top conduit entry installation details (NOT RECOMMENDED) P:\Standard IOMs - Current Release\42004 Instr. Manuals\42004-338J.docx 10/17...

  • Page 6: Model 227-001

    Pub. 42004-338J Rugged Analog Auto-Dial Telephones Page 4 of 21 Model 227-001 The mounting and wiring instructions for the Model 227-001 Public Auto-Dial Telephone are as follows: 1. Remove the eight security screws from the front panel. Remove the front panel and set aside. : There is a 7-foot half- modular telephone cord attached to the PCBA on the rear.
  • Page 7 Pub. 42004-338J Rugged Analog Auto-Dial Telephones Page 5 of 21 7. Pull the telephone line through the conduit and into the enclosure. Connect the telephone’s modular cord to the incoming subscriber line with the appropriate connector. Verify operation by calling to and from another telephone.

  • Page 8: Model 247-001

    Pub. 42004-338J Rugged Analog Auto-Dial Telephones Page 6 of 21 Model 247-001 1. Remove the four front panel screws using a standard Phillips screwdriver, and remove the front panel assembly and set aside. Disconnect the 7-foot half-modular telephone cord from the PCBA terminal strip (if connected).
  • Page 9 Pub. 42004-338J Rugged Analog Auto-Dial Telephones Page 7 of 21 Figure 8. Model 247-001 Mounting Diagram P:\Standard IOMs - Current Release\42004 Instr. Manuals\42004-338J.docx 10/17...

  • Page 10: Model 257-001

    Pub. 42004-338J Rugged Analog Auto-Dial Telephones Page 8 of 21 Model 257-001 1. Open the front door and remove the four outermost screws from the mid-section using a standard Phillips screwdriver. Carefully pull the enclosure apart until encountering a slight resistance on the left side.
  • Page 11 Pub. 42004-338J Rugged Analog Auto-Dial Telephones Page 9 of 21 8. Connect the telephone cord to the PCBA terminal strip. See Figure 7 for details. 9. Close the front half of the enclosure and secure it by replacing the four outermost screws. 10.

  • Page 12: Model 277-001

    Pub. 42004-338J Rugged Analog Auto-Dial Telephones Page 10 of 21 Model 277-001 Flush-Mount Installation Refer to Figure 12 for additional installation information. Figure 11. Model 277-001 Outline Drawing 1. When mounting this telephone in a Model 234 Series Stanchion or for flush-mount installations, the supplied back box must be used to mount the Model 277-001 Telephone.

  • Page 13: Surface-Mount Installation Using A 236-00X Series Or Model 238-001 Enclosure

    Pub. 42004-338J Rugged Analog Auto-Dial Telephones Page 11 of 21 Figure 12. Model 277-001 Back Box Mounting Detail Surface-Mount Installation using a 236-00x Series or Model 238-001 Enclosure : The back box included with the Model 277-001 Telephone is not required for use with a Model 236 Series or Model 238-001 Surface-Mount Enclosure and should be removed.

  • Page 14: Models 277-001Bh And 277-001Bhac

    Pub. 42004-338J Rugged Analog Auto-Dial Telephones Page 12 of 21 Models 277-001BH and 277-001BHAC Flush-Mount Installation Refer to Figure 13, Figure 14, Figure 15, and the following instructions for mounting and wiring the Models 276-001BH and 276-001BHAC Behavioral Health Telephones: Figure 13.

  • Page 15: Surface-Mount Installation Using The No. 238-001Fs Enclosure

    Pub. 42004-338J Rugged Analog Auto-Dial Telephones Page 13 of 21 2. Feed the telephone line through either of the cable entry holes in the dust cover. : Telephone line connections directly to TB1 are acceptable. 3. Connect the telephone’s modular cord to the incoming subscriber line with appropriate connector. Verify operation by calling to and from another telephone.

  • Page 16: Programming Auto-Dial Numbers

    Pub. 42004-338J Rugged Analog Auto-Dial Telephones Page 14 of 21 Programming Auto-Dial Numbers 1. Remove the front panel assembly by following the appropriate instructions provided in this manual for your phone. 2. Insert the supplied portable keypad and cable into J7. 3.

  • Page 17: Maintenance

    Pub. 42004-338J Rugged Analog Auto-Dial Telephones Page 15 of 21 Maintenance Service If your telephone requires service, contact your GAI-Tronics Regional Service Center for a return authorization number (RA#). Equipment should be shipped prepaid to GAI-Tronics with a return authorization number and a purchase order number. If the equipment is under warranty, repairs will be made without charge.

  • Page 18: Volume Control Jumper Setting

    Pub. 42004-338J Rugged Analog Auto-Dial Telephones Page 16 of 21 Volume Control Jumper Setting The handset receiver volume control is factory set to default to its original setting (0 dB) when the telephone is hung up. To save the volume control setting, jumper J4, which is factory set at positions 2 and 3, must be moved to positions 1 and 2.

  • Page 19: Replacement Parts And Accessories

    Pub. 42004-338J Rugged Analog Auto-Dial Telephones Page 17 of 21 Replacement Parts and Accessories Table 1. Replacement Parts Part No. Description ® 10111-104 Handset Assembly with 6-foot Hytel   Coiled Cord, Volume Control, and Noise- Canceling Mic, Black 10117-001 Handset Assembly with 15-inch Armored ...
  • Page 20 Pub. 42004-338J Rugged Analog Auto-Dial Telephones Page 18 of 21 Table 2. Available Accessories Part No. Accessories  12565-009 Ring Relay Kit   12565-010 Ring Relay Kit  12573-001 Spring Door Kit  12576-117 Front Panel Replacement Kit 230-001 Pole Mounting Kit, Rugged Phone/RF ...

  • Page 21: Specifications

    Pub. 42004-338J Rugged Analog Auto-Dial Telephones Page 19 of 21 Specifications Electrical (Typical) Auto-dialer ........Maximum 31 digits, with internal 12-button pad, field-programmable Frequency response ....................... 300 to 3,000 Hz Inter-digit pause ........................... 100 ms Minimum loop current ......................... 20 mA Signaling tone (DTMF) ....................
  • Page 22 Pub. 42004-338J Rugged Analog Auto-Dial Telephones Page 20 of 21 Model 277-001 Enclosure construction: Front panel ......14-gauge (0.075 inch) type 304 brushed stainless steel Enclosure construction: Back box..16-gauge (0.060 inch) cold-rolled steel with black polyester finish Dimensions Front panel ................12.00 H × 10.00 W in (305 × 254 mm) Back box (overall)........
  • Page 23 Pub. 42004-338J Rugged Analog Auto-Dial Telephones Page 21 of 21 User Instructions (USA) This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.
  • Page 24 Warranty Equipment. GAI-Tronics warrants for a period of one (1) year from the date of shipment, that any GAI-Tronics equipment supplied hereunder shall be free of defects in material and workmanship, shall comply with the then-current product specifications and product literature, and if applicable, shall be fit for the purpose specified in the agreed-upon quotation or proposal document.

This manual is also suitable for:

Gai-tronics 247-001Gai-tronics 257-001Gai-tronics 277-001Gai-tronics 227-001

Table of Contents