Advertisement

Quick Links

Published 09/20
This Operator's Manual is an integral part of the safe operation of this machine and must
be maintained with the unit at all times. READ, UNDERSTAND, and FOLLOW the Safety
and Operation Instructions contained in this manual before operating the equipment. C01-
Cover
®
BUSH HOG
2501 Griffin Ave.
Selma, AL 36703
334-874-2700
www.bushhog.com
OPERATOR'S MANUAL
© 2020 Alamo Group Inc.
BBX48/60/
65/72
BOX BLADE
Part No. 50071569
$0.00

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the BBX48 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Bush Hog BBX48

  • Page 1 BBX48/60/ 65/72 BOX BLADE Published 09/20 Part No. 50071569 OPERATOR’S MANUAL This Operator's Manual is an integral part of the safe operation of this machine and must be maintained with the unit at all times. READ, UNDERSTAND, and FOLLOW the Safety and Operation Instructions contained in this manual before operating the equipment.
  • Page 2 BEFORE YOU START! Read the safety messages on the implement and shown in your manual. Observe the rules of safety and common sense! For future reference, record your Bush Hog product model number and serial number. Dealer Telephone Model Number...
  • Page 3: Table Of Contents

    TABLE OF CONTENTS SAFETY SECTION ......................1-1 General Safety Instructions and Practices ......................1-2 Cancer and Reproductive Harm www.P65Warnings.ca.gov ..............1-8 PARTS INFORMATION ............................. 1-8 Decal Location ..............................1-9 Decal Description ............................. 1-10 FEDERAL LAWS AND REGULATIONS ......................1-11 INTRODUCTION SECTION ....................2-1 ASSEMBLY SECTION ......................
  • Page 5: Safety Section

    SAFETY SECTION Safety Section 1-1...
  • Page 6: General Safety Instructions And Practices

    SAFETY General Safety Instructions and Practices A careful operator is the best operator. Safety is of primary importance to the manufacturer and should be to the owner/operator. Most accidents can be avoided by being aware of your equipment, your surroundings, and observing certain precautions.
  • Page 7 SAFETY Never operate the Tractor or Implement until you have read and completely understand this Manual, the Tractor Operator’s Manual, and each of the Safety Messages found in the Manual or on the Tractor and Implement. Learn how to stop the tractor engine suddenly in an emergency.
  • Page 8 SAFETY Never allow children to operate, ride on, or come close to the Tractor or Implement. Usually, 16-17 year-old children who are mature and responsible can operate the implement with adult supervision, if they have read and understand the Operator’s Manuals, been trained in proper operation of the tractor and Implement, and are physically large enough to reach and operate the controls easily.
  • Page 9 SAFETY PROLONGED EXPOSURE LOUD NOISE CAUSE PERMANENT HEARING LOSS! Tractors with or without an Implement attached can often be noisy enough to cause permanent hearing loss. We recommend that you always wear hearing protection if the noise in the Operator’s position exceeds 80db. Noise over 85db over an extended period of time will cause severe hearing loss.
  • Page 10 SAFETY Periodically inspect all moving parts for wear and replace when necessary with authorized service parts. Look for loose fasteners, worn or broken parts, and leaky or loose fittings. Make sure all pins have cotter pins and washers. Serious injury may occur from not maintaining this machine in good working order.
  • Page 11 SAFETY Operate the Tractor and/or Implement controls only while properly seated in the Tractor seat with the seat belt securely fastened around you. Inadvertent movement of the Tractor or Implement may cause serious injury or death. (SG-29) Be particularly careful when transporting the Implement with the Tractor. Turn curves or go up hills only at a low speed and using a gradual steering angle.
  • Page 12: Cancer And Reproductive Harm Www.p65Warnings.ca.gov

    These parts are made and tested to Bush Hog specifications. Non-genuine "will fit" parts do not consistently meet these specifications. The use of “will fit” parts may reduce equipment performance, void warranties, and present a safety hazard. Use genuine Bush Hog parts for economy and safety.
  • Page 13: Decal Location

    SAFETY Decal Location NOTE: Bush Hog supplies safety decals on this product to promote safe operation. Damage to the decals may occur while in shipping, use, or reconditioning. Bush Hog cares about the safety of its customers, operators, and bystanders, and will replace the safety decals on this product in the field, free of charge (Some shipping and handling charges may apply).
  • Page 14: Decal Description

    SAFETY Decal Description BBX 48/60/65/72/ 09/20 Safety Section 1-10 © 2020 Alamo Group Inc.
  • Page 15: Federal Laws And Regulations

    SAFETY FEDERAL LAWS AND REGULATIONS This section is intended to explain in broad terms the concept and effect of federal laws and regulations concerning employer and employee equipment operators. This section is not intended as a legal interpretation of the law and should not be considered as such.
  • Page 17: Introduction Section

    INTRODUCTION SECTION Introduction Section 2-1...
  • Page 18 INTRODUCTION This Box Blade is designed with care and built with quality materials by skilled workers. Proper assembly, maintenance, and operating practices, as described in this manual, will help the owner/operator get years of satisfactory service from the machine. The purpose of this manual is to familiarize and instruct. The Assembly Section instructs the owner/operator in the correct assembly of the Blade using standard and optional equipment.
  • Page 19 INTRODUCTION NOTE: All references made in this manual to right, left, front, rear, top or bottom are as viewed facing the direction of forward travel with implement properly attached to tractor. This Box Blades fit a wide range of tractors. The Heavy-Duty, CAT I three-point hitch, 4" x 4"...
  • Page 20 NOTE: Warranties are honored only if completed “Owner Registration and Warranty” forms are received by Bush Hog within thirty days of delivery of the implement. 3. Record the Model and Serial Numbers on Warranty Page at the front of the Operator’s Manual. Keep this as part of the permanent maintenance file for the Implement.
  • Page 21 2. If the unit has been subjected to misapplication, abuse, misuse, negligence, fire or other accident. 3. If parts not made or supplied by Bush Hog have been used in connection with the unit, if, in the sole judgement of Bush Hog such use affects its performance, stability or reliability.
  • Page 23: Assembly Section

    ASSEMBLY SECTION Assembly Section 3-1...
  • Page 24 ASSEMBLY DEALER SET-UP INSTRUCTIONS This Box Blade is shipped completely assembled from the factory. Always use personal protection devices such as eye and ear protectors during assembly. BBX 48/60/65/72/ 09/20 Assembly Section 3-2 © 2020 Alamo Group Inc.
  • Page 25: Operation Section

    OPERATION SECTION Operation Section 4-1...
  • Page 26 OPERATION BOX BLADE OPERATION INSTRUCTIONS Your Box Blade should now be assembled and inspected for any evidence of defective or damaged parts before use. Any evidence of damage should be reported to your dealer immediately. After the Three-Point Hitch is attached, carefully remove safety blocks from Moldboard pivot Point. This section of the Operator’s Manual is designed to familiarize, instruct, and educate safe and proper blade use to the operator.
  • Page 27: Standard Equipment And Specifications

    OPERATION Standard Equipment and Specifications 48” 60” 65” 72” Working Width 48” 60” 66” 72” Height of Moldboard 15-5/8” 15-5/8” 15-5/8” 15-5/8” Box Depth 22” 22” 22” 22” Overall Depth 27” 27” 27” 27” Overall Height 33” 33” 33” 33” Overall Width 49”...
  • Page 28: Operator Requirements

    OPERATION 2. OPERATOR REQUIREMENTS Safe operation of the unit is the responsibility of a qualified operator. A qualified operator has read and understands the implement and tractor Operator’s Manuals and is experienced in implement and tractor operation and all associated safety practices. In addition to the safety messages contained in this manual, safety signs are affixed to the implement and tractor.
  • Page 29: Tractor Requirements

    OPERATION 3. TRACTOR REQUIREMENTS Operating the blade with a tractor that does not meet the following requirements may cause tractor or blade damage and be a potential danger to the operator and passersby. Tractor Requirements and Capabilities • ASABE approved Roll-Over Protective Structure (ROPS) or ROPS cab and seat belt. •...
  • Page 30: Tractor 3-Point Hitch

    OPERATION 3.3 Tractor 3-Point Hitch For the Box Blade, the tractor 3-point hitch must be rated to lift at least 260 lbs. for the 48”, 325 lbs. for the 60’, 375 lbs for the 65”, and 390 lbs for the 72”. The Box Blade can attach to tractors with a CAT l/ QH.
  • Page 31: Boarding The Tractor

    OPERATION 4.1 Boarding the Tractor Use both hands and equipped handrails and steps for support when boarding the tractor. Never use control levers for support when mounting the tractor. Seat yourself in the operator’s seat and secure the seat belt around you.
  • Page 32: Starting The Tractor

    OPERATION 5. STARTING THE TRACTOR The operator must have a complete understanding of the placement, function, and operational use of all tractor controls before starting the tractor. Review the tractor operator’s manual and consult an authorized dealer for tractor operation instructions if needed. Essential Tractor Controls: •...
  • Page 33: Connecting The Blade

    OPERATION 6.1 Connecting the Blade 1. Shorten or remove the tractor drawbar to avoid interference when raising and lowering the blade. 2. Board the tractor and start the engine. Position the tractor to the blade with the 3-point lift arms positioned between the respective set of blade A-frame lift lugs.
  • Page 34: Pre-Operation Inspection And Service

    OPERATION 7. PRE-OPERATION INSPECTION AND SERVICE Before each use, a pre-operation inspection and service of the implement and tractor must be performed. This includes routine maintenance and scheduled lubrication, inspecting that all safety devices are equipped and functional, and performing needed repairs. DO NOT operate the unit if the pre-operation inspection reveals any condition affecting safe operation.
  • Page 35: Blade Pre-Operation Inspection/Service

    OPERATION 7.2 Blade Pre-Operation Inspection/Service Before each use, a complete inspection and service is required to ensure the blade is in good and safe working condition. Damaged and/or broken parts should be repaired and/or replaced immediately. To ensure the blade is ready for operation, conduct the following.
  • Page 36 OPERATION Tractor PRE-OPERATION Inspection Tractor ID#:________________________Make:________________________ Date:______________________________Shift:________________________ Before conducting the inspection, make sure the tractor engine is off, all rotation has stopped and the tractor is in park with the parking brake engaged. Make sure the implement is resting on the ground or securely blocked up and all hydraulic pressure has been relieved.
  • Page 37 OPERATION Blade & Box Blade PRE-OPERATION Inspection Blade ID#:_______________________Make:__________________________ Date: ___________________________Shift:___________________________ Before conducting the inspection, make sure the tractor engine is off, all rotation has stopped and the tractor is in park with the parking brake engaged. Make sure the blade is resting on the ground or securely blocked up and all hydraulic pressure has been relieved.
  • Page 38: Driving The Tractor And Implement

    OPERATION 8. DRIVING THE TRACTOR AND IMPLEMENT Safe tractor transport requires the operator possess a thorough knowledge of the model being operated and precautions to take while driving with an attached implement. Ensure the tractor has the capacity to handle the weight of the implement and the tractor operating controls are set for safe transport.
  • Page 39: Starting The Tractor

    OPERATION 8.1 Starting the Tractor The procedure to start the tractor is model specific. Refer to the tractor operator’s manual for starting procedures for your particular tractor. Consult an authorized dealer if the starting procedure is unclear. Ensure the 3-point control lever is in the lowered position and the PTO is disengaged before starting the tractor.
  • Page 40: Driving The Tractor And Implement

    OPERATION 8.3 Driving the Tractor and Implement Start off driving at a slow speed and gradually increase your speed while maintaining complete control of the tractor and unit. Moving slowly at first will also prevent the tractor from rearing up and loss of steering control. The tractor should never be operated at speeds that cannot be safely handled or which will prevent the operator from stopping quickly during an emergency.
  • Page 41: Backfilling And Snow Removal

    OPERATION 9.2 BACKFILLING AND SNOW REMOVAL The backfilling operation should be performed with the load in the center of the blade. Avoid concentrated loads on end of the blade. DO NOT ram into a load at any time, as this multiplies the force several times above normal and could result in damage to your blade.
  • Page 42: Blade And Storage

    OPERATION 12. BLADE AND STORAGE Properly preparing and storing the blade and rake at the end of the season is critical to maintaining its appearance and to help ensure years of dependable service. The following are suggested storage procedures: • Thoroughly clean all debris off the unit to prevent damage from rotting grass and standing water.
  • Page 43 OPERATION Transport only at speeds where you can maintain control of the equipment. Serious accidents and injuries can result from operating this equipment at high speeds. Understand the Tractor and Implement and how it handles before transporting on streets and highways. Make sure the Tractor steering and brakes are in good condition and operate properly.
  • Page 44: Transporting On Public Roadways

    OPERATION Before transporting the tractor on a public roadway or boarding a trailer for transport, the tractor brake pedals should be locked together. Locking the pedals ensures that both wheels brake simultaneously while stopping, especially when making an emergency stop. Use extreme caution and avoid hard applications of the tractor brakes when towing heavy loads at road speeds.
  • Page 45 OPERATION The SMV (Slow-Moving Vehicle) emblem is universal symbol used to alert drivers of the presence of equipment traveling on roadways at a slow speed. SMV signs are a triangular bright orange with reflective red trim for both easy day and night visibility.
  • Page 46: Hauling The Tractor And Implement

    OPERATION 14.2 Hauling the Tractor and Implement Before transporting a loaded tractor and implement, measure the height and width dimensions and gross weight of the complete loaded unit. Ensure that the load will be in compliance with the legal limits set for the areas that will be traveled through.
  • Page 47: Troubleshooting Guide

    OPERATION 15. TROUBLESHOOTING GUIDE Problem Possible Cause Remedy Shearing M/B Carrier Lack of lubrication Lubricate Pivot Pin Pivot Pin Bolt Bolt not tightened properly Tighten Bolt to proper torque Bent Moldboard Small curve is normal from weld pull Can be removed but will not affect operation Hitting hidden objects Know soil conditions, keep...
  • Page 48 OPERATION Problem Possible Cause Remedy Hydraulic Pump not shutting Using Open Center Valve Replace Valve or Conversion Plug off on Closed Center System and Main Relief Open Center Conversion Plug Replace with Closed Center Plug Pumping over Relief Valve Replace with No Relief Plug Oil leaking at hose connection Connection not tight Tighten connection...
  • Page 49: Maintenance Section

    MAINTENANCE SECTION Maintenance Section 5-1...
  • Page 50: Replacing Scarifier Points

    MAINTENANCE Replacing Scarifier Points Make certain that you wear gloves and safety glasses. Chips can fly off hammer or punch and cause eye damage, loss of eyesight, or other injury. Place Scarifier assembly in vise securely. Using a hammer and drift or punch, drive the worn point off. Hammer the new point on securely.
  • Page 51 MAINTENANCE BBX 48/60/65/72/ 09/20 Maintenance Section 5-3 © 2020 Alamo Group Inc.
  • Page 53 TO THE OWNER/OPERATOR/DEALER To keep your implement running efficiently and safely, read your manual thoroughly and follow these directions and the Safety Messages in this Manual. The Table of Contents clearly identifies each section where you can easily find the information you need. The OCCUPATIONAL SAFETY AND HEALTH ACT (1928.51 Subpart C) makes these minimum safety...
  • Page 54 BBX 48/60/65/72 Box Blade BBX 48/60/65/72-SOM-09/20 P/N 50071569 Printed U.S.A...

This manual is also suitable for:

Bbx60Bbx65Bbx72

Table of Contents