Table of Contents
Advertisement
BASIC OPERATION
NOTE:
• While you are viewing a source screen, you can also select the input signal directly by pressing the INPUT "1" through "10"
button. In this case INPUT buttons function as follows:
When using the projector in stand alone operation:
Input Mode
Input Module
A
With RGB board*
With VIDEO board
*1 Some settings allow you to automatically retrieve a COMPONENT singnal after an RGB signal by pressing the INPUT "1"
button. See "RGB/COMPONENT Search Setting" on the Set-up manual.
*2 When the RGB input is set, an RGB signal is selected; when the VIDEO input is set, a VIDEO or S-VIDEO is selected.
The RGB input board allows you to switch input signals depending on settings. See the "Part Names and Functions-Optional
Boards" on the Set-up manual for more detailed information.
Numbers designate INPUT buttons on the remote control.
When using the projector with the ISS-6020/ISS-6020G:
INPUT 1 through 10 → Selects the corresponding number slot of the ISS-6020/ISS-6020G
When using the projector with two ISS-6020/ISS-6020G or more:
To switch to another input signal, enter the master slot number, then the slave slot number by using INPUT buttons and press
ENTER.
Example:If you want to select a signal from the no.3 slot of the slave Switcher which is connected to the no.2 slot of the master Switcher, first
press the INPUT "2" button, then the INPUT "3" button and then press ENTER.
• You can switch to any input signal of NO 01 through10 on the INPUT SELECT list by holding down the CTL button and pressing
one of the INPUT buttons corresponding to the input number. To activate this function you must first select ENABLE in the
DIRECT ENTRY ACCESS mode. For further details, contact your dealer.
• If there are two or more memory locations that contain the same signal information the projector will reference the signal nearest
the beginning of the list. To select the next signal use the CURSOR
Page / total pages – sheet No.
Connect condition of the Switcher
P 0 1 / 1 0 – 1
I N P U T S E L E C T
S T A N D A L O N E
N O
N A M E
S O U R C E
0 1
N T S C 3 . 5 8
V I D E O
0 2
N T S C 4 . 4 3
V I D E O
P A L
V I D E O
0 3
0 4
S E C A M
V I D E O
0 5
V E S A 1 0 2 4
R G B
0 6
0 7
0 8
0 9
1 0
OUTPUT DATA : LIST NO.
Signal name
Input terminal
RGB
1
B
4
2
C
7
B
–
C
–
INPUT SELECT List Format
I N P U T
A
A
A
A
A
Rgistered input module
Output data for the signal currently projected.
VIDEO
S–VIDEO
2
3
4
5
7
8
4
5
7
8
or
button and press ENTER.
P 0 1 / 1 0 – 2
N O
0 1
0 2
0 3
0 4
0 5
0 6
0 7
0 8
0 9
1 0
28
COMPONENT
10*
1
Standard
4
Optional
7
(XGRGBIN(A))
–
Optional
–
(XGVIDIN(B))
I N P U T S E L E C T
S T A N D A L O N E
D A T E
F H
0 0 / 0 0 / 0 0
1 5 . 7 4 k H z
0 0 / 0 0 / 0 0
1 5 . 7 4 k H z
0 0 / 0 0 / 0 0
1 5 . 7 4 k H z
0 0 / 0 0 / 0 0
1 5 . 7 4 k H z
0 0 / 0 0 / 0 0
4 8 . 6 0 k H z
OUTPUT DATA : LIST NO.
Entry date
Horizontal
Frequency
F V
6 0 . 0 0 H z
6 0 . 0 0 H z
5 0 . 0 0 H z
5 0 . 0 0 H z
6 0 . 0 0 H z
Vertical
Frequency
Advertisement
Table of Contents
