Gtech Pro 2 K9 ATF308 - Vacuum Cleaner Manual

Thank you for choosing Gtech

" I started Gtech to create sensible, easy to use products that do a great job. Your opinion is important to us and we'll use your feedback to improve our products and services, and to let other people know what it's like to be part of the Gtech family."

Nick Grey – Inventor, owner of Gtech

What's in the box

1. Main unit (1 bag fitted)
2. Battery (fitted)
3. Extension tube (x2)
4. Power floor head
5. Dusting brush
6. Crevice tool
7. Charger
8. Power Brush
9. Spare Carbon bags x6 scented
10. cartridges (1 fitted to lid)
11. Hair removal tool

Tool configurations

Operation

1. Press the large button above the handle to turn the product on and off.
   
   
2. The product has 2 power settings: Max mode (higher suction power and shorter runtime) and Eco mode (lower suction power and longer runtime). Change modes by sliding the switch located in front of the On/Off button. The product will turn on in the mode it was last used.
   

Power floor head assembly

To use the product in floor cleaning mode, join the 2 sections of the extension tube and fit the power floor head at the end. Ensure all parts are correctly lined up and push them into place. Ensure the product is switched off before removing or fitting attachments.
To disassemble, place your fingers in the indents of the tube, grip and pull the sections apart

1. Place your foot gently on the head of the vacuum and pull the body back towards you. You will hear a click.
   
   
2. A forward motion will pick up larger pieces of debris.
   
   
3. Pulling the vacuum back towards you activates the AirLOC and picks up finer particles.
   

Removing and cleaning the brush bar

1. Before you remove the brush bar, you will need to remove the power floor head from the extension tube. Rotate the latch on the side of the powered floor head to the 'unlock' position and pull out the brush bar.
   
   
2. To remove hair from the brush bar, use the hair removal tool to cut the hair before pulling it out. Never operate the power floor head without the brush bar in place.
   

Above the floor cleaning

For above the floor cleaning, you can fit the crevice tool or dusting brush for reachable areas or fit the extension tube with an accessory for high up cleaning

LED headlight

There is a headlight on top of the product to illuminate the area being cleaned.

State of charge

1. The battery state of charge indicator shows how much charge the product has. As you use the product, the green lights will turn off in a downwards direction.
   
   
2. While the battery is on charge, the LEDs will pulsate and illuminate in turn. When the battery is fully charged, all of the LEDs will be solid green.
   

Battery charging

1. When a single green light flashes, recharge the battery.
   
   
2. Plug the charger in and connect it to the charging port on the side of the battery.
   
   
3. After 4 hours, all 4 LEDs will show solid green and charging is complete.
   
   
4. You can also charge the product for 1 hour for a burst of cleaning.
   

Removing the battery

1. Pull the latch at the top of the battery to remove.
   
   
2. The battery can be charged on or off the main unit.
   

Refitting the battery

1. To replace the battery, slot it into the front of the product from the bottom first, with the latch facing outwards.
   
   
2. Push the battery into the slot until it clicks into place. If you want to buy a spare battery, go to www.gtech.co.uk or call 08081 685 028.
   
   

Bag installation

1. Remove the lid by pulling gently upwards.
   
   
2. Fit the bag collar onto the tube underneath the lid and push it up firmly.
   
   
3. New bags have a tendency to sit flat when first attached. Pull the bag down to sit vertically.
   
   
4. To get maximum efficiency from the bag, it is important to expand the bag before insertion.
   Do not use the vacuum without a bag: it may damage the motor and will invalidate your warranty.
   

Bag removal

1. Once the bag is attached and straightened, place the lid back onto the main body, making sure the bag cap is also inserted.
   
   
2. When the bag is full, lift the lid and remove it from the product with bag attached.
   
   
3. Carefully remove the bag from the product lid to avoid squashing contents. Insert the bag cap to secure contents.
   
   
4. Dispose of the bag and replace with a new one. (You can get more bags at www.gtech.co.uk or by calling 08081 685 028).
   Do not reuse bags as this could damage and reduce the performance of the product.
   

If the suction is low when the bag is empty and a new bag is fitted you may have a blockage

1. Remove the battery and lid and look through the nozzle. Remove any blockages.
   
   
2. Remove the bag from the lid. Check for any blockages in the lid. Remove any blockages.
   
   
3. The tools can block sometimes, too.
   
   
4. A light above the window on the top of the lid allows visibility into the bag to indicate when the bag is full or if there is a blockage.
   

Power brush

1. To attach the power brush, slot it over the standard nozzle. The power must be off while changing nozzles. The power button will now power the brush as well as the suction.
   
   
2. To remove the power brush, press the buttons on the sides of the attachment and pull it away from the main unit.
   
   
3. To clean the brush bar, first remove the power brush. Rotate the latch from the 'lock' to the 'unlock' position and pull out the brush bar.
   
   
4. To remove hair from the brush bar, run the hair removal tool down the groove to cut the hair, then pull it out. Never operate the power head without the brush bar in.
   

Optional extras

Scented cartridge

1. Remove the scented cartridge from its box, celophane wrapper and slide the plastic sleeve off.
   
   
2. Slide the scented cartridge into the opening on the right side of the lid.
   If the cartridge is missing the product will not seal and the performance will be much lower.
   If your original cartridge no longer smells, it can still be used. If you'd like new scented cartridges, go to www.gtech.co.uk or call 08081 685 028.
   

Flexible power hose

The flexible power hose attaches in the same way as the other accessories and can be used as it is or with the the addition of other tools. Powered units can fit directly to the flexible power hose.

Car Accessory Kit

The three tools from the Car Accessory Kit fit directly into the nozzle of the product.

Wall mount

1. Install your wall mount at least 1072mm from the floor. Universal fixings have been included - please use the correct fixings for the wall type you're mounting this item to. Please use a stud finder to ensure no water pipes or electrical cables are hit. If you are unsure, please seek professional advice.
   
   
2. The tools can be stored like this on the wall mount. Your wall mount will look like the picture on the right when fully assembled with the product.
   
   
3. Pull the detachable tool kit out from the fixed section of the wall mount.
   
   
4. You can also carry the detachable part of your wall mount with you while you clean - attach it to your belt. Extra precautions must be taken to ensure you do not damage the product or injure yourself.
   

Product care

Your product doesn't need much maintenance: keep it clean, check for blockages, remove hair from the brush bar and charge the battery. Wipe it with a dry cloth if it gets dirty. Never wash it with liquid, run it under a tap or use it without the bag. Regularly check if the bag is full.

Troubleshooting

Product support

If these initial tips do not solve your problem, we have various other ways to help.
Visit: www.gtech.co.uk/support

	Online
	Live chat support
	support@gtech.co.uk
	How to videos

GTECH PRO 2 TECHNICAL SPECIFICATION

Documents / Resources

References

• Gtech UK Official: Vacuum Cleaners, Home & Gardening
• Support and Customer Service | Gtech

Download manual

Here you can download full pdf version of manual, it may contain additional safety instructions, warranty information, FCC rules, etc.

Download Gtech Pro 2 K9 ATF308 - Vacuum Cleaner Manual