LG ProCentric 55UV560H Commercial Mode Setup Manual page 36

Installer Menu (Cont.)
029 - REMAP AUX INPS
Set to 1 to remap the PTC's direct tune channels for Aux inputs
from 13x to 9x. This allows 2-digit only tuning systems (i.e.,
legacy On Command Video™) to direct tune Aux inputs. See also
Reference section, "TV Aux Input Configuration."
030 - ACK MASK
MPI Communication Parameter. When set to 1, enables the ACK
feature of MPI.
031 - POLL RATE
MPI Communication Parameter. Selects the poll rate for MPI. Step
size of 16 ms. Changing from default may affect communication
via MPI.
032 - TIMING PULSE
MPI Communication Parameter. Sets the baud rate for MPI. Step
size of 4.3 uS. Changing from default may affect communication
via MPI.
035 - HDMI1 ENABLE
Set to 1 to enable HDMI 1 input in DTV Mode. Set to 2 to enable
HDMI 1 input in PC Mode. Set to 0 to disable display panel HDMI
1 input.
039 - REAR AUX EN. (Rear Aux Enable)
Set to 1 to enable display panel rear Aux (AV) input. Set to 0 to
disable display panel rear Aux (AV) input.
041 - SIMPLINK EN
Set to 0 to disable the SIMPLINK feature. Set to 1 to enable
SIMPLINK functionality (does not enable remote control access to
the SIMPLINK Menu).
Note: When both this item and item 042 AUTO INPUTS are
enabled in the Installer Menu, HDMI inputs will be detected by
SIMPLINK, but the Auto Input(s) Sensing Feature will not function.
042 - AUTO INPUTS
Determines the Aux inputs for which auto-sensing is enabled. Set
to 0 to disable auto-sensing for all available inputs. Set to 255 to
enable auto-sensing for all available inputs. For information on
options for individual input settings, see Reference section, "Auto
Input(s) Sensing Feature."
Note: In order for auto-sensing to be enabled for an input, that
input must also be enabled in the Installer Menu. For example, to
enable auto-sensing for HDMI 1, item 035 HDMI1 ENABLE must
also be set to 1 or 2. Also, see note above regarding TV operation
when both this item and item 041 SIMPLINK EN are enabled.
36
046 - STRT AUX SRCE (Start Aux Source)
Sets the starting Aux source. When turned ON, the TV will tune to
starting Aux source if item 004 STRT CHANNEL is set to 0.
1 = AV 3 = HDMI 1
7 = HDMI 3 255 = Last Aux
Note: In order for an Aux input to be selected as the starting Aux
source, the input also must be enabled in the Installer Menu.
Note: This item is not available in the Installer Menu unless item
004 STRT CHANNEL is set to 0.
047 - AUX STATUS
Controls the MPI status channel response for Aux sources. Set to
1 for the Aux source to be reported as its channel number. Set to
0 for the Aux source to be reported as channel 0. See Reference
section, "TV Aux Input Configuration," for Direct Access channel
numbers.
049 - DIS. AUDIO M. (Disable Audio Menu)
Determines the availability of the Sound Out (Audio) Menu in the
TV menus. Also determines the default Audio Mode when TV is
turned ON. See the table below and set as required.
Sound Out
Value
Menu Status
0 (default) Enabled
1 Disabled
2 Enabled
3 Disabled
4 Enabled
5 Disabled
8 Enabled
9 Disabled
Note: If a SIMPLINK-enabled device is connected to the TV
and item 041 SIMPLINK EN is set to 1 (enabled), the SIMPLINK
device Audio Mode will have priority over the setting of this item
when the TV is turned ON.
053 - DIS. CH-TIME (Disable Channel-Time Display)
Set to 1 to disable the TV's native Channel-Time display when a
custom channel label/channel information will be provided by the
MPI command. Set to 0 to enable the TV's native Channel-Time
display.
069 - EN. CH-T COL. (Enable Display Characters Custom Color)
Set to 1 to enable custom color for the Channel-Time display. Set
to 0 to disable custom color for the Channel-Time display.
5 = HDMI 2
Default Audio Mode at TV
Turn ON
TV Speaker
TV Speaker
External Speaker (Optical/HDMI ARC)
External Speaker (Optical/HDMI ARC)
LG Sound Sync (Optical)
LG Sound Sync (Optical)
TV Speaker + Audio Out (Optical)
TV Speaker + Audio Out (Optical)
206-4326