Table of Contents
Advertisement
Quick Links
Page
Contents
2
1.
3
2.
4
4
3.
4
5
5
7
7
4.
8
9
12
14
15
16
5.
AXCOR PROFILE 400
AXCOR PROFILE 400 HC
INSTRUCTION MANUAL
INDEX
Congratulations on choosing a Claypaky product!
We thank you for your custom.
Please note that this product, as all the others in the
rich Claypaky range, has been designed and made with
total quality to ensure excellent performance and best
meet your expectations and requirements.
C61769
C61768
Advertisement
Table of Contents
Related Manuals for Claypaky C61769
Summary of Contents for Claypaky C61769
-
Page 1: Table Of Contents
We thank you for your custom. Page Contents Please note that this product, as all the others in the rich Claypaky range, has been designed and made with Safety information total quality to ensure excellent performance and best Unpacking and preparation meet your expectations and requirements. -
Page 2: Safety Information
1. SAFETY INFORMATION IMPORTANT: Claypaky recommends you carefully read and keep the safety information on this product, also SAFETY INFORMATION available in digital format at the following link: Ref: FIS00T - Safety Information Axcor 400 series www.claypaky.com IMPORTANTE: Claypaky raccomanda di leggere accuratamente e conservare le informazioni di sicurezza relative... -
Page 3: Unpacking And Preparation
2. UNPACKING AND PREPARATION 2 x 183102/805 Packing contents - Fig. 1 UNLOCKED LOCKED PAN Mechanism Lock and Release (every 90°) - Fig. 2 TILT Mechanism Lock and Release (every 45°) - Fig. 3 AXCOR PROFILE 400 400 HC... -
Page 4: 3.1 Installing The Fixture
3. INSTALLATION AND START-UP 3.1 Installing the fixture Installing the projector - Fig. 4 The projector can be installed on the floor resting on special rubber feet, on a truss or on the ceiling or wall. WARNING: with the exception of when the projector is positioned on the floor, the safety cable must be fitted. (Cod. 105041/001 available on request). This must be securely fixed to the support structure of the projector and then connected to the fixing point at the centre of the base. -
Page 5: Connecting The Control Signal Line: Dmx / Art-Net
Mains Connecting to the mains supply - Fig. 6 3.3 Connecting the control signal line: DMX / Art-Net DMX 512 5 PIN SCREEN SIGNAL SIGNAL Connecting to the control signal line (DMX) - Fig. 7 Use a cable conforming to specifications EIA RS-485: 2-pole twisted, shielded, 120Ohm characteristic impedance, 22-24 AWG, low capacity. Do not use microphone cable or other cable with characteristics differing from those specified. - Page 6 Reversal of the display - Fig. 9 To activate this function, press UP and DOWN keys simultaneously while the display is in the rest mode. This status will be memorised and maintained even for the next time it will be switched on. To return to the initial state, repeat the operation all over again. On each projector, the starting address must be set for the control signal (addresses from 1 to 512).
-
Page 7: Opening The Covers Maintenance
4. MAINTENANCE 4.1 Opening the covers 1/4 Turn 1/4 Turn Locking and releasing Pan and Tilt movements - Refer to the instructions in the UNPACKING AND PREPARATION section. Opening the head covers - Fig. 10. Closing the head covers - Fig. 11. Continue AXCOR PROFILE 400 400 HC... -
Page 8: Periodical Cleaning
• General cleaning of internal parts. • Restoring lubrication of all parts subject to friction, using lubricants specifically supplied by Claypaky. • General visual check of the internal components, cabling, mechanical parts, etc. -
Page 9: Effects Module Removal
4.3 Effects module removal Upper side Extraction of the effect modules - Fig. 13. Insertion of the effect modules: Repeat the operations indicated in Fig. 13, 14 and 15 in reverse order. IMPORTANT: Grasp the modules using the support structure and not the details which could get damaged. NOTE: - Do not disconnect wiring harnesses when the fixtures is switched-on, to avoid to damage electronic boards. - Page 10 Upper side Extraction of the effect modules - Fig. 14. Insertion of the effect modules: Repeat the operations indicated in Fig. 13, 14 and 15 in reverse order. IMPORTANT: Grasp the modules using the support structure and not the details which could get damaged. NOTE: - Do not disconnect wiring harnesses when the fixtures is switched-on, to avoid to damage electronic boards.
- Page 11 Upper side Extraction of the effect modules - Fig. 15. Insertion of the effect modules: Repeat the operations indicated in Fig. 13, 14 and 15 in reverse order. IMPORTANT: Grasp the modules using the support structure and not the details which could get damaged. NOTE: - Do not disconnect wiring harnesses when the fixtures is switched-on, to avoid to damage electronic boards.
-
Page 12: Cleaning Of The Filters
4.4 - Cleaning of the filters 1/4 Turn Cleaning of the filters - Fig. 16. AXCOR PROFILE 400 400 HC... - Page 13 1/4 Turn Cleaning of the filters - Fig. 17. AXCOR PROFILE 400 400 HC...
-
Page 14: Rotating Gobos
INDEX Replacing rotating gobos - Fig. 19 - Before use custom gobos contact Claypaky; - The original gobos have a special coating designed specifically to resist to the high temperatures; - The rotating gobo wheel only use dichroic glass gobos (it is not possible to use metal gobos);... -
Page 15: Battery Removal
4.6 Battery removal Battery removal - Fig. 20 This product contains a rechargeable battery. To preserve the environment, please dispose the battery at the end of its life according to the regulation in force. AXCOR PROFILE 400 400 HC... -
Page 16: Specifications
Fault in the electronic circuits. Call an authorised technician. Lenses broken Call an authorised technician. Dust or grease deposited. Clean (see instructions). - Via Pastrengo, 3/b - 24068 Seriate (BG) Italy - Tel. +39-035-654311 - Fax +39-035-301876 - www.claypaky.com Clay Paky S.p.A.
Need help?
Do you have a question about the C61769 and is the answer not in the manual?
Questions and answers