Related Manuals for Hinkley HOVER FLUSH 52
Summary of Contents for Hinkley HOVER FLUSH 52
- Page 1 52" HOVER FLUSH ™ INDOOR / OUTDOOR LED FAN DC MOTOR WIFI CEILING FAN INSTRUCTION MANUAL...
- Page 2 SO WE’RE HERE IF YOU HAVE A QUESTION, NEED SOME HELP OR WANT TO CHAT ABOUT OUR PRODUCTS. SEND SUGGESTIONS OUR WAY TOO—WE’RE ALWAYS LOOKING TO MAKE YOUR EXPERIENCE WITH HINKLEY A POSITIVE ONE. > SERVICE@HINKLEY.COM > 800.HINKLEY > LET’S SEE THAT HINKLEY STYLE @HINKLEY...
-
Page 3: Table Of Contents
TROUBLESHOOTING INSTALLING THE FAN ENERGY GUIDE ELECTRICAL CONNECTIONS SPECIFICATIONS FINISHING THE INSTALLATION SMART BY BOND INSTALLING THE BLADES WARNING: Read and follow these instructions carefully and be mindful of all warnings shown throughout. ©2019 Hinkley Lighting, Inc. | hinkley.com |... - Page 4 If the battery compartment does not close securely, stop using the product and keep it away from children. If you think batteries might have been swallowed or placed inside any part of the body, seek immediate medical attention. | hinkley.com...
-
Page 5: Important Safety Precautions
These factors must be supplied by the person(s) installing, caring for and operating the unit. TOOLS & MATERIALS REQUIRED • PHILLIPS SCREWDRIVER • FLAT SCREWDRIVER • WRENCH OR PLIERS • WIRE CUTTER • STEPLADDER • WIRING SUPPLIES AS REQUIRED BY ELECTRICAL CODE ©2019 Hinkley Lighting, Inc. | hinkley.com |... -
Page 6: Unpacking Your Fan
Blade to Motor Screws MH900852Fxx w/Lock Washers and Flat Washers, Balance Kit, Safety cable hardware (wood screw, flat washer) NOTE: Design of parts shown above may look slightly different for XX=FAN FINISH your specific model of fan. | hinkley.com... -
Page 7: Preparation
The Bracket outlet box must be able to support a minimum of 35 pounds. Attach mounting bracket to outlet box using screws provided with the Screws outlet box. ©2019 Hinkley Lighting, Inc. | hinkley.com |... -
Page 8: Installing The Fan
Firmly tighten screw in the clamp. Cut off excess cable. (Fig. 2) Safety Cable Loop You are now ready to make the electrical connections. Wood Screw And Washer Safety Cable Fig. 2 | hinkley.com... -
Page 9: Electrical Connections
Connect the WHITE receiver neutral wire to the WHITE building neutral wire. Connect the COPPER building ground wire to the 4 YELLOW/GREEN ground wires from the fan and receiver. YELLOW GRAY BLACK Receiver WHITE Fig. 1 Fig. 2 ©2019 Hinkley Lighting, Inc. | hinkley.com |... -
Page 10: Finishing The Installation
Raise the decorative ring up against the mounting bracket, the four supports inside the decorative ring should be placed against the four slots on the mounting bracket, twist the decorative ring clockwise until snug (Fig. 2). Screws Mounting Bracket Fig. 1 Studs Decorative Ring motor Fig. 2 | hinkley.com... -
Page 11: Installing The Blades
Line up the two slotted holes with the two loose screws on the mounting hub located on fan motor. Re-install the third screw removed and tighten all three. Mounting Hub Screws Adapter Plate ©2019 Hinkley Lighting, Inc. | hinkley.com |... -
Page 12: Installing The Led Assembly And Glass Shade
Raise glass shade up against adapter plate and secure it to the fan by turning the glass shade clockwise until snug. DO NOT Screws OVERTIGHTEN. Fig. 1 Restore power and your light kit is ready for operation. Adapter Plate Glass Shade Fig. 2 | hinkley.com... -
Page 13: Installing The Wall Control
Remote transmitter will be held in place with built in magnets. Cradle B Wall plate Plastic Face plate Outlet box anchor Transmitter Wall plate Cradle A Face plate Transmitter Wall Fig. 1 HIRO Control System Fig. 2 ©2019 Hinkley Lighting, Inc. | hinkley.com |... - Page 14 Attach the cradle A to the wall switch box using the supplied hardware. Attach the multi-gang faceplate to the switch set in the wall outlet box. Cradle A of Hinkley switch will fit in any standard decora face plate. Remote transmitter will be held in place with built in magnets.
-
Page 15: Operation
NOTE: A single fan can be controlled with as many as 3 wall controls in one room. Every control will need to repeat the pairing process based on instructions above and all controls must be within 30 feet of the fan. ©2019 Hinkley Lighting, Inc. | hinkley.com |... - Page 16 An UPWARD airflow moves warmer air off the ceiling area as shown in Figure 4. This allows you to set your heating unit on a cooler setting without affecting your comfort. SUMMER MODE WINTER MODE (COUNTERCLOCKWISE DIRECTION) (CLOCKWISE DIRECTION) Fig. 3 Fig. 4 | hinkley.com...
-
Page 17: Care And Cleaning
If the blade wobble is still noticeable, interchanging two adjacent (side by side) blades can redistribute the weight and possibly result in smoother operation. Check to assure all dowrods to motor hardware and/or hanger ball are tight. Make sure ceiling box is secure. ©2019 Hinkley Lighting, Inc. | hinkley.com |... -
Page 18: Energy Guide
• Your cost depends on rates and use Amps 0.31 0.05 • Energy Use: 13.1 Watts All estimates based on typical use, excluding lights ftc.gov/energy RPMs Airflow Shown Is a Weighted Average of High and Low Cubic Feet per Minute Based on Downrod | hinkley.com... -
Page 19: Smart By Bond
SMART BY BOND HINKLEY SMART FAN OPTIONS: • Brute Force Method In addition to the included wall control, you can control your Hinkley fan a) Turn mains power OFF to the fan. through the Bond app. b) Turn mains power back ON on the fan. - Page 20 HINKLEY IS PROUD TO PROVIDE YOU WITH CEILING FAN PRODUCTS THAT ENHANCE YOUR SPACE WITH COMFORT, PURPOSE AND STYLE. AS A FAMILY COMPANY, WE ARE COMMITTED TO DESIGN, PERFORMANCE AND QUALITY, AND WHAT’S IMPORTANT TO YOU IS PARAMOUNT TO US.
- Page 21 GLOBAL HEADQUARTERS 33000 Pin Oak Parkway | Avon Lake, Ohio 44012 T (440) 653 5500 | F (440) 653 5555 | hinkley.com...