Kenwood TK-3402(U) Service Manual page 10

TK-3402(U)/3402/3407
2-3. IF Amplifi er Circuit
The fi rst IF signal is passed through a four-pole mono-
lithic crystal fi lter (XF400) to remove the adjacent channel
signal. The fi ltered fi rst IF signal is amplifi ed by the fi rst IF
amplifier (Q403) and is then applied to the IF system IC
(IC400).
The IF system IC provides a second mixer, limiting
amplifier, quadrature detector and RSSI (Received Signal
Strength Indicator). The second mixer mixes the fi rst IF sig-
nal with the 50.85MHz signal of the second local oscillator
output (Q403) and produces the second IF signal of 450kHz.
The second IF signal is passed through the ceramic fi lter
(CF401) to remove the adjacent channel signal. The fi ltered
second IF signal is amplified by the limiting amplifier and
demodulated by the quadrature detector with the ceramic
discriminator (CD400). The demodulated signal is routed to
the audio circuit.
2-4. Audio Amplifi er Circuit
The demodulated signal from IC400 is sent to an AF am-
plifi er through IC705, and is routed to an audio power ampli-
fi er (INT:IC709,EXT:IC707) where it is amplifi ed and output
to the speaker.
IC400 IC705
Baseband
FM IC
IC
Fig. 3 Audio Amplifi er circuit
2-5. Squelch Circuit
Part of the AF signal from the IC400 enters the FM IC
(IC400) again, and the noise component is amplified and
rectifi ed by a fi lter and an amplifi er to produce a DC voltage
corresponding to the noise level.
The DC signal from the FM IC goes to the analog port of
the MCU (IC702). IC702 determines whether or not to output
sounds from the speaker by checking if the input voltage is
higher or lower than the preset value.
To output sounds from the speaker, IC702 sends a high
signal to the AFSW line and turns IC707 on through Q709,
Q710, Q713 and Q716. This explanation is a case of exter-
nal speaker amplifier. In the case of internal loudspeaker
amplifi er, IC702 sends a high signal to the AFSW line and
turns IC709 on through Q711 and Q714.
10
CIRCUIT DESCRIPTION
IC707
AF PA SPO EXT
(EXT) SP
IC709
AF PA INT
(INT) SP
3. Transmitter System
3-1. Microphone Amplifi er Circuit
The signal from the microphone is limited by the AGC
circuit, which is composed of D700, D701, Q705, Q706 and
the mute switch (Q704). IC705 is composed of a high-pass
fi lter, low-pass fi lter and pre-emphasis/IDC circuit.
The signal from the microphone and the low speed data
from the MCU (IC702) enter the baseband IC (IC705) and
pass through each path and are mixed inside the IC.
The output signal from the audio processor goes to the
VCO modulation input. The other output signal goes to the
TCXO modulation input.
MIC IC705
Baseband
D702,703
AGC
Q705,706
LSD
SW
MICM
OUT
Q704
Fig. 4 Microphone amplifi er circuit
3-2. Drive and Final Amplifi er Circuit
The signal from the T/R switch (D15 is on) is amplifi ed by
the pre-drive amplifi er (Q201) to 20mW.
The output of the pre-drive amplifi er is amplifi ed by the
drive amplifi er (Q206) and the RF fi nal amplifi er (Q208) to
5.0W (1W when the power is low).
The drive amplifi er and the RF fi nal amplifi er consist of
two MOS FET stages.
The output of the RF final amplifier is then passed
through the harmonic fi lter (LPF) and antenna switch (D203
and D204) and is applied to the antenna terminal.
3-3. APC Circuit
The APC circuit always monitors the current flowing
through the drive amplifi er (Q206) and the RF power ampli-
fi er (Q208) and keeps a constant current. The voltage drop
at R230, R231 and R233 is caused by the current fl owing
through the RF fi nal amplifi er. This voltage is applied to the
differential amplifi er IC200 (1/2).
IC200 (2/2) compares the output voltage of IC200 (1/2)
with the reference voltage from IC705(32pin:AUXDAC1). The
output of IC200 (2/2) controls the gate bias voltage of the
RF power amplifi er and the drive amplifi er to make both volt-
ages the same.
The change of power high/low is carried out by the
change of the reference voltage.
VCO
X1
TCXO
MOD1