Advertisement
Dear Customer,
Congratulations and thank you very much for choosing a quality product by NIVONA. In order to enjoy your new NIVONA appliance to its best, please read this manual and pay attention to the safety tips before rst use. Please keep this manual safe. You can use it for references and hand it over to a future owner. Enjoy your coffee and the top quality appliance by NIVONA.
fig. 1
S1 | Water tank | |
S2 | Drip tray | |
S3 | Coffee strength | |
S4 | Lid of coffee powder chute | |
S5 | Two cups | |
S6 | Filter | |
S7 | Descaling | |
S8 | Automatic switch-off | |
S9 | Temperature | |
S10 | Rinsing | |
S11 | Cleaning | |
S12 | Steam valve | |
S13 | Bar |
Attention :
Repairs to electrical appliances must only be undertaken by a professional! Improper repairs may result in severe danger for the user! Should the appliance be used or maintained improperly or incorrect, the warranty shall become void!
Attention :
Using the on/off switch (fig.1/J) during the brewing process may damage the appliance! Turn the appliance off only after it has finished the job.
Attention :
risk of burning! When drawing steam or hot water, a shot of hot water may spray from the steam/hot water jet or the Spumatore (fig. 1/L); allow the coffee spout, the steam/hot water jet and the Spumatore to cool down before you touch it.
CE – This appliance conforms to valid EG regulations.
(Please read this and follow instructions before you brew your first coffee!)
The following are included in the package contents:
Tip: In case of customer service being required, the appliance should be shipped in its original pack- aging. Please keep this safe, including the polystyrene parts.
Before you set the basic settings and brew your first coffee, please make yourself familiar with the main controls of your appliance.
Attention :
Only use clear, cold water for the water tank! Never use sparkling water or any other liquids! Non-compliance will render warranty claims void.
Attention :
Never use beans that have been treated during or after roasting with supplements like sugar or similar. This may cause damages to the mill. Resulting repairs are not covered by the warranty.
Tip: For production reasons the internal pipes may be empty when setting the appliance up for the first time. The appliance will show this as follows: the symbol S12 will display when the mains are connected and the ON/OFF switch (fig. 1/J) has been pushed.
After a short while the symbol S12 will show up in display.
Symbol S10 will now appear.
It is up to you whether you would like to use the appliance with or without filter.
A Claris filter is included in the delivery (NICR 530). Using this filter, the appliance needs descaling less often because the filter softens the water. Ex factory the setting is "no filter".
Attention :
Do not overtighten or break.
Depending on the presets, one, two or three beans are shown in the display. The appliance is now ready for use.
Tip: If you are using a filter, the internal water softening is automatically set to water hardness level 1! The appliance needs descaling less frequently – but always descale when called upon to do so and always with the FIILTER REMOVED.
The filter will be flat after approx. 50 l of water have been drawn (see chapter 4.1. how to change the filter).
Attention :
Even if the display does not indicate "Change filter" by highlighting the symbol , the filter needs changing after a maximum of two months if the appliance is not used regularly (see chapter 4).
Depending on the water hardness in your area, the appliance needs to be descaled every now and again. For the system to be able to indicate that this is necessary, you need to set the correct water hardness prior to first use.
Using the appliance with the filter and the appropriate settings (see above) the water hardness is automatically set to level 1.
First test the water quality with the enclosed test strip.
Test strip / Degree of hardness = Display
1 red dot / 1–7° = LEVEL 1 = 1 red bar
2 red dots / 8–14° = LEVEL 2 = 2 red bars
3 red dots/ 15–21° = LEVEL 3 = 3 red bars
4 red dots / >21° = LEVEL 4 = 4 red bars
Tip: If the test strip does not show any red dot, please set up level 1.
Attention :
Should you want to use the appliance without filter, the water hardness must be set. This is important because depending on the water hardness the appliance needs to be descaled more often (ex factory the appliance comes with the setting "use without filter; level 3 water hardness"!).
Depending on the presets, one, two or three beans are shown in the display. The appliance is now ready for use.
This function allows you to determine the automatic switch-off time after the last use. The ex factory setting is "after 5 minutes".
In doing so you increase the number of bars at the bottom of the display one bar at a time according to your personal preference:
1 bar = automatic switch-off time after 5 minutes
2 bars = automatic switch-off time after 30 minutes
3 bars = automatic switch-off time after 70 minutes
Depending on the presets, one, two or three beans are shown in the display. The appliance is now ready for use.
You can adjust the temperature as required to "normal", "high" or maximum". The ex factory setting is "high".
In doing so you increase the number of bars at the bottom of the display one bar at a time. Set the level for your preferred temperature in accordance with the number of red bars. The bars read as follows:
1 bar = temperature "normal"
2 bars = temperature "high"
3 bars = temperature "maximum"
After 3 bars the display starts again with one bar.
Optionally you can activate the automatic off-rinsing process for additional hygiene after the appliance has been switched off.
The ex factory setting is "off".
In doing so you increase the number of bars at the bottom of the display one bar at a time. Set the level for your preferred temperature in accordance with the number of red bars:
1 bar = automatic off-rinsing „off"
2 bars = automatic off-rinsing „on"
After 2 bars the display starts again with one bar.
Depending on the presets, one, two or three beans are shown in the display. The appliance is now ready for use.
Attention :
Only adjust the grinding coarseness whilst the grinder is running.
You can adjust the grinder according to the particular blend of bean. We suggest the grinder is kept on a medium setting.
To change the coarseness of the grinding, please follow these steps:
The grinding coarseness control is at the top right (fig. 11).
The smaller the dot, the finer the coffee powder. Please note:
Check out for yourself the best setting according to your personal taste.
To reset the factory settings proceed as follows:
The factory setting has been reset.
Tip: Ex factory the appliance is set so that you can brew your first coffee straightaway. But we do recommend to make the necessary adjustments according to your personal preferences. Hence check chapter 2 "Getting started" first and follow its instructions!
Tip: When you use the appliance for the first time or if it hasn't been used for a prolonged period of time the first cup will not have the full aroma and should therefore not be consumed.
Once you have completed the instructions (chapter 2), the procedure for switching the appliance on is always similar:
The display shows 5 flashing red bars. When the system has reached its operating temperature, the display will show symbol S10 .
The system is now being rinsed. The appliance is now ready for use. Depending on the presets, one, two or three beans are shown in the display.
Tip: if you do not use the appliance for a prolonged period of time (e.g. holidays), switch it off using the on/off switch (fig. 1/J) and pull the mains plug.
The coffee strength can be set in three levels according to taste which the display will show:
MILD, the display features one bean, about 7 grams of ground coffee, e.g. for latte or cappuccino;
STANDARD, the display features two beans, about 9 grams of ground coffee, e.g. for coffee;
STRONG, the display features three beans, about 11 grams of ground coffee, e.g. for espresso or strong coffee.
As soon as the appliance is operational, the display will show either its latest preset or the ex factory setting.
Once you've chosen coffee strength (see chapter 3.2) and water volume (see chapter 3.3),
The spout is adjustable in height to match the size of the cup.
The appliance will now start grinding, pre-brewing and brewing.
The process can be aborted any time by pressing the coffee button again.
Attention :
When making your first coffee, the grinder box is still empty. It can therefore happen that the symbol S3 will flash after the first grinding and the appliance will not make any coffee.
Tip: The water volume can be adjusted while making coffee. Check out for yourself the best setting according to your personal taste and the size of the cup.
Tip: To remember the ideal setting for your personal taste, proceed as follows:
Make a note of the coffee strength / volume selector's position for the size of the coffee cup.
Once you've chosen coffee strength (see chapter 3.2) and water volume (see chapter 3.3),
The spout is adjustable in height to match the size of the cups.
The display will show symbol S5 .
The appliance will now start grinding, pre-brewing and brewing.
The process can be aborted any time by pressing the coffee button (fig. 1/D) again.
When making two cups the grinder will automatically do two rounds.
Attention :
When making your first coffee, the grinder box is still empty. It can therefore happen that the symbol S3 will flash after the first grinding and the appliance will not make any coffee.
Tip: In case there is not enough water or the bean container runs out during the two grinding cycles or the trays need emptying, the respective symbols will show on the display. In that case the second cup will not be brewed. Follow the display and press the coffee button (fig. 1/D) again for the second cup.
Symbol S4 is flashing.
The appliance will now start pre-brewing and brewing – without grinding.
Tip: If you have opened the lid of coffee powder chute accidentally or did not press the coffee button after having poured in the ground coffee, the appliance will automatically start rinsing for a minute once the lid is closed. The appliance will then be operational again.
Attention :
The coffee powder chute is not a storage container. Therefore never pour in more than one portion of coffee and only use fresh or vacuum-packed coffee ground from coffee beans. Do not use water-soluble instant coffee!
Risk of scalding! Escaping water may spray! The steam/hot water jet /the Spumatore becomes very hot when used. Let the steam/hot water jet /the Spumatore cool down for a few minutes before touching it. Only touch the rubber parts.
Tip: You can draw hot water for about 2 minutes, after that the appliance will automatically shut down. By turning the steam/hot water control (fig. 1/C) backwards and forwards, you can re-start the process.
The special Spumatore frothing aid (fig. 1/L) can froth milk directly into the cup from a container.
Whilst heating-up 5 red bars will flash at the bottom of the display. As soon as symbol S12 shows, you can draw steam and froth milk.
Attention :
A small amount of water will initially precede the milk froth.
Tip: You can draw hot steam for about. 2 minutes, after that the appliance will automatically shut down. By turning the steam/hot water knob (fig. 1/C) back and forth, you can re-start the process.
Attention :
Dried milk residue on the steam/hot water jet is dif ficult to remove. Clean immediately after it has cooled off!
Whilst heating-up 5 red bars will flash at the bottom of the display. As soon as symbol S12 shows, you can draw steam.
Attention :
A small amount of water will initially precede the steam.
The appliance is now back to coffee mode.
Attention :
From time to time (ideally each time the appliance will not be used for a while, at any rate in regular intervals!) the Spumatore needs to be completely dismantled (fig. 3) and thoroughly cleaned under running water.
Attention :
If your appliance needs cleaning or maintenance, the display will show the respective sym- bol. Please always follow these instructions, otherwise your warranty will be void. Read chapters 4.1 to 4.5 for further information. Should you wish to maintain or clean your device without being asked to do so, please also follow the instructions in chapters 4.1 to 4.5.
The filter will be flat after about 50 l of water have been drawn. The display shows symbol S6 .
You can still make coffee, but we recommend to always change the filter immediately.
Attention :
The filter needs changing after a maximum of two months if the appliance is not in regular use. The display will show no status signal. Use the dial (by the month) at the top of the filter to select the date of change.
The device will heat up briefly and is ready for use again.
If the device needs cleaning, the display will show symbol S11 .
Tip: You can continue making coffee or draw hot water and steam, but we recommend to start the cleaning program as soon as possible. Otherwise the function might be impaired and your warranty could be compromised.
Attention :
Do not disrupt the cleaning process. Follow the instructions exactly in the stated order. Insert cleaning tab only if the appliance asks for it.
Tip: During the cleaning process the red bars at the bottom of the display will show the progress. The more bars that are visible, the further the program has advanced.
Symbol S11 flashes on the display, symbols S1 and Symbol S2 are on.
The appliance starts cleaning. When finished symbol S4 will additionally show.
The cleaning process starts. Symbol S11 flashes. The cleaning process is automatic and will run for about 10 minutes. Once the process has finished, symbol S2 , is on and symbol S11 flashes.
The appliance briefly heats up. It is ready for use again when the bean symbols in the display are on.
Manual cleaning
If required the cleaning program can also be started and run as described in chapter 4.2, without the prompt of symbol S11 .
If the appliance needs descaling, symbol S7 appears on the display.
Tip: You can continue making coffee or draw hot water and steam, but we recommend to start the desca- ling program as soon as possible. Otherwise the function might be impaired and your warranty could be compromised.
Attention :
Do not disrupt the descaling program. Follow the instructions exactly in the stated order. Never use vinegar or vinegar-based agents, only standard liquid products specifically recommended for automatic coffee machines.
Attention :
Before starting the descaling program remove the filter from the water tank.
Tip: During the descaling program the progress is displayed through the red bars at the bottom of the display. The more bars are shown the further the progress.
The appliance briefly heats up. It is ready for use again when the bean symbols in the display are on.
Attention :
Please remove any descaler residues on the casing immediately with a damp cloth.
Manual descaling
If required the descaling program can also be started and run as described above, without the prompt of symbol S7 .
Tip: Please follow these cleaning instructions as working with foodstuffs demands the highest degree of cleanliness.
Attention :
Never immerse the appliance in water! Do not use abrasive cleaning agents.
Occasionally use a little soapy water for cleaning.
TIP: Dried milk residue is dif ficult to remove.
Attention :
From time to time (ideally each time the appliance will not be used for a while, at any rate in regular intervals!) the steam/hot water jet needs to be completely dismantled and thoroughly cleaned under running water (fig.3).
We recommend our special cleaning agent for milk residue NICC 705.
Attention :
Remove the brew unit only when the appliance is switched off.
When necessary the brew unit can be removed and cleaned under cold, running water. Never use any cleaning agent, but clear, cold water only! For hygienic reasons we recommend the removal and cleaning of the unit thoroughly after each run of the cleaning program (see chapter 4.2).
Report | Cause | Solution |
S3 flashes | No beans | Add beans, restart coffee making |
S12 | Refill water pipe system Filter possibly defective | Turn steam/hot water control clockwise Remove or replace filter |
S1 on | Water tank is empty | Fill water tank |
Water tank is missing or inserted incorrectly | Reinsert water tank | |
S2 on | Drip tray and/or used coffee container full | Empty drip tray and/or used coffee container |
S2 flashes | Drip tray with used coffee container missing or tted incorrectly | Reinsert drip tray with used coffee container |
S11 on | System cleaning required | Clean system (see chapter 4.2) |
S7 on | System descaling necessary | Descale system (see chapter 4.3) |
S6 on | Filter exhausted | Change filter (see chapter 4.1) |
S13 bar 1 and bar 5 flash alternately | Brew unit fitted incorrectly | Fit brew unit correctly and snap into place (see chapter 4.5) |
Fault | Cause | Solution |
No hot water or steam | Blocked steam/hot water jet/ Spumatore (fig.1/L) System may be calcified |
|
Not enough milk froth or liquid froth | Unsuitable milk Blocked steam/hot water jet / Spumatore |
|
Coffee only drips | System may be calcified Coffee is too finely ground Coffee powder too fine |
|
No "crema" on the coffee | Unsuitable coffee beans Beans may be too old Grinding coarseness not adjusted to beans |
|
Strong noise from coffee grinder | Foreign matter in grinder, e.g. small stones |
|
In the event of a fault or a system report which you cannot correct yourself, please contact our email (info@nivona.com) or Service-Hotline: 0049 911-25266390
If the system detects any errors, the display will show an error report
Attention :
Please make a note of the flashing or lit up bars. Switch the appliance off and pull the mains plug. Then call the service hotline 0049-911-25266390 or email (info@nivona.com) us with name type, serial number (see type label, fig.1/S) and error number. Our service team will take care of the next steps.
Fresh water filter NIRF 700:
New fresh water filters are available from well-stocked local dealers.
Cleaning tabs NIRT 701:
New cleaning tabs are available from well-stocked local dealers.
Descaling agent NIRK 703:
New descaling agents are available from well-stocked local dealers.
Special milk residue cleaner NICC 705:
Special milk residue cleaner is available from well-stocked local dealers.
MilkCooler NICT 500:
This top-quality stainless steel milk cooler keeps milk „fridge cold" for a long time and delivers the best frothing results.
Customer service
Nivona products are manufactured to the highest quality standards. Should any question arise with regards to your appliance, please do not hesitate to write to us. Only with your active support will we be able to improve our products and further develop them, so that they will fully satisfy your demand. In the event that you need to ship your faulty appliance directly to us, please make sure that no residual water remains in the system:
Your appliance is now ready for shipment.
Tip: Please make sure that you pack the appliance very carefully before shipping, ideally in the original packaging. The manufacturer will assume no liabilities for damage in transit.
Guarantee and customer service terms and conditions
Please find detailed information about guarantee and customer service terms and conditions in the accompanying document.
Please dispose of filters with domestic waste.
Disposal of your old appliance and packaging
Please keep the original packaging. It will serve as protection should you need to ship the appliance in the event of a customer service issue.
Electrical and electronical appliances often contain valuable, but sometimes also environmentally damaging material and should therefore not be disposed of as normal household waste. They may damage human health and harm the environment when wrongfully handled or left among residual waste. Therefore please drop your old or irreparably damaged appliance at your local community waste collection/recycling centre.
Further information is available from the dealer where you bought the appliance, your town hall or waste collector.
Voltage 220 - 240V AC, 50/60 Hz
Power consumption 1455 W
NIVONA Apparate GmbH
Südwestpark 90
D-90449 Nürnberg Germany
www.nivona.com
© 2017 by NIVONA
Here you can download full pdf version of manual, it may contain additional safety instructions, warranty information, FCC rules, etc.
Advertisement
Thank you! Your question has been received!
Need Assistance?
Do you have a question about the CafeRomatica NICR 520 that isn't answered in the manual? Leave your question here.