Table of Contents
Advertisement
Quick Links
OPERA
OPERA T T T T T OR'S MANU
OPERA
OPERA
OPERA
Revision #00
3131 Starting Serial #615687
3137 Starting Serial #616625
3143 Starting Serial #619636
H&S MANUFACTURING CO.,INC.
P.O. BOX 768 (715) 387-3414 FAX (715) 384-5463
3131/3137/3143
3131/3137/3143
3131/3137/3143
3131/3137/3143
3131/3137/3143
OR'S MANU
OR'S MANU
OR'S MANU AL
OR'S MANU
WARNING
Manufactured By
MARSHFIELD, WISCONSIN 54449
Heavy Duty
Spreader
READ AND UNDERSTAND THIS MANUAL
BEFORE OPERATING THIS EQUIPMENT.
UNSAFE OPERATION OR MAINTENANCE OF
THIS EQUIPMENT CAN RESULT IN SERIOUS
INJURY OR DEATH.
HSMFG1215
AL
AL
AL
AL
Part #75898
Advertisement
Table of Contents
Related Manuals for H&S 3131
Summary of Contents for H&S 3131
- Page 1 BEFORE OPERATING THIS EQUIPMENT. UNSAFE OPERATION OR MAINTENANCE OF THIS EQUIPMENT CAN RESULT IN SERIOUS WARNING INJURY OR DEATH. Revision #00 3131 Starting Serial #615687 3137 Starting Serial #616625 3143 Starting Serial #619636 HSMFG1215 Part #75898 Manufactured By H&S MANUFACTURING CO.,INC.
-
Page 2: Table Of Contents
CONTENTS Warranty & Warranty Registration Card ..........1-2 Manufacturers Statement . -
Page 5: Dealer Pre-Delivery Checklist
H&S DEALER PRE-DELIVERY CHECK LIST AFTER COMPLETION, DEALER SHOULD REMOVE AND RETAIN FOR RECORDS After the Manure Spreader has been completely set-up, check to be certain it is in correct operating order before delivering to the customer. The following is a list of points to inspect. Check off each item as you have made the proper adjustments and found the item operating satisfactorily. - Page 6 Intentionally Left Blank...
-
Page 7: Dealer Delivery Checklist
DEALER DELIVERY CHECK LIST AFTER COMPLETION, DEALER SHOULD REMOVE AND RETAIN FOR RECORDS This check list that follows is an important reminder of valuable information that should be passed on to the customer at the time this Manure Spreader is delivered. Check off each item as you explain it to the customer. - Page 8 Intentionally Left Blank...
-
Page 9: Safety Information - Be Alert Symbol
SAFETY INFORMATION YOUR SAFETY ALERT! IS INVOLVED. THIS SYMBOL IS USED THROUGHOUT THIS BOOK WHENEVER YOUR PERSONAL SAFETY IS INVOLVED. TAKE TIME TO BE CAREFUL. REMEMBER: THE CAREFUL OPERATOR IS THE BEST OPERATOR. MOST ACCIDENTS ARE CAUSED BY HUMAN ERROR. CERTAIN PRECAUTIONS MUST BE OBSERVED TO PREVENT THE POSSIBILITY OF INJURY OR DAMAGE. -
Page 10: Safety Information - Explanation Of Safety Signs
SAFETY INFORMATION Keep signs in good condition. Immediately replace any missing or damaged signs. RECOGNIZE SAFETY INFORMATION This is the safety-alert symbol. When you see this symbol on your machine or in this manual, be alert to the potential for personal injury. Follow recommended precautions and safe operating practices. -
Page 11: Safety Decals
SAFETY INFORMATION... - Page 12 SAFETY INFORMATION -10-...
-
Page 13: Safety Information - Warning - Owner Must Read And Understand
SAFETY INFORMATION TRACTOR: This operators manual uses the term “Tractor” when identifying the power or the towing source. W A R N I N G TO PREVENT SERIOUS INJURY OR DEATH BEFORE YOU ATTEMPT TO OPERATE THIS EQUIPMENT, READ AND STUDY THE FOLLOWING INFORMATION. -
Page 14: Cap Screw Torque Values
-12-... -
Page 15: Set-Up & Assembly
(Shown w/optional upper beater for details. Make sure lights are functioning properly. on 3131/3137) SAFETY CHAIN (Optional) Follow state and local regulations regarding use of a safety chain and transport lighting when towing farm equipment on public highways. -
Page 16: Preparing For Operation
PREPARING FOR OPERATION TRACTOR CONNECTIONS Tractor Hitch 15-3/4” for 1000 RPM Fasten the spreader hitch to the drawbar with a hitch pin with a safety locking device. Remove the weight from the jack (jack is not to be used when spreader is loaded). Remove jack from pipe mount and place on convenient storage mount located on the top of left hitch channel. -
Page 17: Operation
OPERATION EMERGENCY SHUTDOWN If a foreign object becomes lodged in the beater area and shears the shear bolt, disengage the PTO. Stop the tractor engine, remove the ignition key, and allow all mechanisms to stop before cleaning or working on the spreader. WARNING: Some photographs used in the following pages show guards or shields removed for clarification. - Page 18 OPERATION SPREADING - WITH OPTIONAL HYDRAULIC DRIVE Engage tractor PTO shaft slowly. Beater is always in the engaged position, therefore, engaging tractor PTO will automatically start beater. Raise the hydraulic tailgate. Open hydraulic valve on tractor connected to speed control valve on Manure Spreader. Control speed of apron by turning speed control handle clockwise to increase speed, counter-clockwise to decrease speed.
-
Page 19: Adjustments
ADJUSTMENTS DRIVE CHAIN To adjust front drive chain, loosen jam nut turn nut on adjusting rod (located at the right hand front side of spreader) clockwise. There should be 1/2” deflection at the center of the drive chain. Over tightening or too loose of a chain will result in excessive wear on the bearing, chain and sprockets. - Page 20 ADJUSTMENTS BEATER CLUTCH ADJUSTMENT It may be necessary to compensate for wear in the beater clutch and clutch control yoke. When properly adjusted the moveable jaw clutch should have one-quarter (1/4”) inch (distance C) between clutches when disengaged. To adjust, loosen jam nut (A) holding spring bracket. With beater disengaged (clean out position), tighten nut (B) against shifter lever bracket until the proper distance between clutch jaws is reached.
-
Page 21: Service
5 bolts, washers, and nuts when replacing. Torque to 60 foot lbs. (Shown w/optional upper beater for 3131/3137) WHEEL BEARING LUBRICATION, CLEAN & RE-PACK INSTRUCTIONS Wheel hubs are equipped with a grease zerk for regular maintenance. Annually disassemble and clean parts in solvent. Reassemble bearings per instructions in the Service Chapter and tighten the castellated nut on the spindle to the point where there is no end-play and a slight drag on the bearings. -
Page 22: Optional Equipment
2nd HYDRAULIC ENDGATE CYLINDER (3131) The H&S 3131 manure spreader is equipped with brackets to accept an optional second cylinder to raise and lower the hydraulic endgate. The optional cylinder is located on right hand side of spreader. The kit includes a cylinder, brace, hoses, and connectors to attach to existing cylinder. - Page 23 OPTIONAL EQUIPMENT HYDRAULIC DRIVE An optional hydraulic drive unit is available to convert from two speed to variable speed hydraulic drive. Hydraulic drive may be used as a two or four hose tractor hook-up. Front Control Panel Hydraulic Motor Shields Removed for Clarity -21-...
-
Page 24: Lubrication Guide
LUBRICATION GENERAL INFORMATION IMPORTANT: Catch and dispose of fluid per local waste disposal regulations whenever service is performed on hydraulic components, valves, cylinders, hoses, etc. GREASE FITTINGS There are numerous grease fittings on the spreader. The operator should become familiar with all lubrication points and establish a systematic routine to insure complete and quick lubrication of the machine. - Page 25 GREASE ZERK LOCATION - Grease every 10 Hours (2) Tailgate Arms (3) PTO Shaft (2) Front jack shaft bearings. (2) Axle Pivot (Model 3131) (2) Rear Drive Shaft (4) Axle Pivot (Model 3137/3143) (1) Beater Clutch Control Yoke (1) Beater...
- Page 26 PART # DESCRIPTION 1494A Warning - Do Not Operate (3 on 3131/3137, 4 on 3143)(1 on Top Beater for 3131/3137) 1494B Warning - Do Not Remove Shields 1494H Danger - Stay Clear - w/Top Beater Only...
-
Page 27: Decal Location
DECAL LOCATION DCAMB 11593C 12794 1494J 1494K 111593A 11211176 UNDER SHIELD DCAMB 72114(3131) 72107(3137) 72108(3143) DCAMB 72103(S3131) 71494A 1494K 093020 72106(S3137/S3143) UNDER SHIELD 71188H (TWO SPEED 72104(3131) 1494A 1494A DECAL) 9194B 72097 11599 DCAMB 72110(3137) 72203A 72111(3143) 1494J 54033 1494B... - Page 28 DECAL LOCATION 72114(3131) 72107(3137) 72102(S3131) 111593A 111593C 72108(3143) 1494B 72105(S3137/S3143) 3494A DCAMB 093020 DCAMB 1494B 9194A 11211176 093020 1494J 1494H 72538 1494A (UNDER SHIELD) 11211176 1494A DCRED 3494A -26-...
-
Page 29: Trouble Shooting
TROUBLE SHOOTING WARNING: MAKE SURE THAT THE TRACTOR IS SHUT OFF AND THE SPREADER CAN NOT MOVE BEFORE SERVICING THE MANURE SPREADER. MAINTENANCE AND REPAIR SERVICE WORK TO BE PERFORMED BY A QUALIFIED SERVICE PERSON ONLY. TROUBLE... POSSIBLE CAUSE... POSSIBLE REMEDY... Beater Does Not Turn PTO Not Turning Engage Tractor PTO... -
Page 30: Service Notes
SERVICE NOTES -28-... -
Page 31: Specifications
SPECIFICATIONS 3131 3137 3143 Top Flare Width......68’....68”....68”... - Page 32 H&S MFG H&S MFG ..CO H&S MFG CO ..H&S MFG H&S MFG products approved for the FEMA FEMA FEMA FEMA FEMA SEAL OF Q SEAL OF Q U U U U U ALITY SEAL OF Q ALITY ALITY...