In The Case Of Technical Problems; Repair Service; Information For Environmental Protection/ Disposal; Spare Parts - Ikra IECS 2240 TF Operating Instructions Manual

• Check the oil level and lubrication of your chain saw
after every use. Insufficient lubrication leads to dam-
age to the chain, bar and motor.
• Check how sharp the chain is every time before you
use the chain saw. A blunt chain will cause overheating
of the motor.
• Sharpening a saw chain requires experience and spe-
cialised knowledge. We therefore recommend to have
sharpening carried out by a specialised workshop.
• Before transporting the chainsaw, always remove the
plug from the power socket and slide the chain guard
over the rail and chain. If several cuts are to be per-
formed with the chain saw, the saw must be switched
off between cuts.
• When using a vehicle to transport the machine, posi-
tion it so that it can cause no danger to persons and
fasten it firmly.
• There are no parts to be maintained inside the de-
vice; the following therefore applies:
- Do not carry out any maintenance tasks that are not
described in these instructions. We cannot accept any
liability for accidents and damage caused by unau-
thorised repair attempts, incorrect use or misuse.

In the case of technical problems

• The machine does not start up:
Check whether the current socket is live. Check
whether the power cable is undamaged. If neither
case applies, take the chainsaw to a specialised work-
shop or the works after-sales service.
• Chain does not run:
Check position of handguard (see fig. 10). Chain only
runs if handguard brake is released.
• Sparks fly at the motor:
Motor or carbon brushes damaged. Take the chainsaw
to a specialised work-shop or the works after-sales
service.
• Oil does not flow:
Check the oil level. Clean the oil flow openings in
the bar (see also the corresponding hints of "Main-
tenance and servicing). If this is not successful, take
the chainsaw to a specialised work-shop or the works
after-sales service.
Attention: Any maintenance or repair work go-
ing beyond that described in these Operating
Instructions may only be carried out by author-
ised persons or the works after-sales service.
Attention: If the power supply lead of this
device shows any defects, the lead must be
replaced by an authorized repair shop only
or through the manufacturer's own service
personnel, as this work requires special tools.

Repair Service

Repairs to electric power tools should only be carried out
by specialist electrical personnel.
Always keep the original packaging for a possibly re-
quired shipping of the tool.
GB | Operating Instructions
Information for environmental protection/
disposal
Dispose of the machine properly after it is worn out. Dis-
connect the mains cable in order to prevent misuse. Do
not dispose of the machine with the household waste. In
the interest of environmental protection, take it to a col-
lection point for electric machines. Your responsible local
authority can provide you with addresses and operating
times. Also take the packaging materials and worn out
accessories to the appropriate collection
In accordance with European Directive 2012/19/EC on
waste electrical and electronic equipment and its imple-
mentation in national law, waste electric tools must be col-
lected separately for environmentally-compatible re-use.
Recycling alternative to the return invitation:
Instead of returning the electric equipment, the owner is
alternatively obligated to take part in the proper recycling
in the case of relinquishment of ownership. The waste
equipment can also be taken to a collection facility which
disposes of it in the sense of the national recycling man-
agement and waste acts. This does not pertain to the ac-
cessory parts and auxiliary equipment without electrical
components accompanying the waste equipment.

Spare parts

If you need accessories or spare parts, please contact our
Service department.
When working with this tool, do not use any accessory parts
other than those recommended by our company. Otherwise
the operator or others in the vicinity could suffer serious
injuries, or the tool could be damaged.
The following information should be provided when or-
dering spare parts:
• Type of machine
• Item number of the machine

Warranty

For this electric tool, the company provides the end user -
independently from the retailer's obligations resulting from
the purchasing contract - with the following warranties:
The warranty period is 24 months beginning from the
hand-over of the device which has to be proved by the
original purchasing document. For commercial use and
use for rent, the warranty period is reduced to 12 months.
Wearing parts and defects caused by the use of not fitting
accessories, repair with parts that are no original parts of
the manufacturer, use of force, strokes and breaking as
well as mischievous overloading of the motor are exclud-
ed from this warranty. Warranty replacement does only
include defective parts, not complete devices. Warranty
repair shall exclusively be carried out by authorized ser-
vice partners or by the company's customer service. In
the case of any intervention of not authorized personnel,
the warranty will be held void.
All postage or delivery costs as well as any other subse-
quent expenses will be borne by the customer.
10
Only for EU countries
Do not discard electric tools in the household
waste!
points.