Ingersoll-Rand SRV125F Series Operation And Maintenance Manual
Ingersoll-Rand SRV125F Series Operation And Maintenance Manual

Ingersoll-Rand SRV125F Series Operation And Maintenance Manual

Starter relay valve

Advertisement

Quick Links

Series SRV125F Starter Relay valves are designed for controlling fluid flow in conjunction with Air Starting
Systems
.
• IMPORTANT SAFETY INFORMATION ENCLOSED - SAVE THESE INSTRUCTIONS.
Read and understand this manual before operating Valve.
• Failure to observe the following warnings could result in injury.
Always install, operate, inspect and maintain this prod-
uct in accordance with all applicable standards and reg-
ulations (local, state, country, federal, etc.).
Always use clean, dry air at a pressure which does not
exceed the pressure rating listed on the valve.
Do not use damaged, frayed or deteriorated air hoses &
fittings.
Always turn off the air and disconnect the air hose
before installing, removing or adjusting any accessory
on this valve, or before performing any maintenance on
this valve or accessory.
Do not lubricate the valve with flammable or volatile
liquids such as kerosene, diesel or jet fuel, use only
recommended lubricants.
Series SRV125F Valves are not designed for working
in explosive atmospheres.
Refer All Communications to the Nearest
Ingersoll-Rand Office or Distributor.
© Ingersoll-Rand Company 2004
P7630 Edition 1
Printed in U.S.A
Operation and Maintenance Manual
Series SRV125F
Starter Relay Valve
NOTICE
WARNING
PLACING THE VALVE IN SERVICE
for
Do not remove any labels, replace any damaged labels.
Operate this valve only when properly installed in the
Air Starting System.
Always bleed off the air pressure before attempting to
remove the Starter Relay Valve from the Receiver or
before attempting to perform any maintenance on the
Starter Relay Valve.
Never attempt to remove the Retaining Ring (12) from
the bottom side of the Starter Relay Valve until the air
pressure has bled off. If the Retaining Ring is removed
while there is pressure in the Receiver, internal parts of
the Starter Relay Valve will be blown out with consid-
erable force.
Use only recommended Ingersoll-Rand accessories.
1
Form P7648
Edition 1
August 2004
CCN 04579728

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the SRV125F Series and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Ingersoll-Rand SRV125F Series

  • Page 1 Starter Relay Valve will be blown out with consid- liquids such as kerosene, diesel or jet fuel, use only erable force. recommended lubricants. • Use only recommended Ingersoll-Rand accessories. • Series SRV125F Valves are not designed for working in explosive atmospheres. Refer All Communications to the Nearest Ingersoll-Rand Office or Distributor.
  • Page 2 NOTICE • The use of other than genuine Ingersoll-Rand replacement parts may result in safety hazards, decreased starter perfor- mance, and increased maintenance, and may invalidate all warranties. • Repairs should be made only by authorized trained personnel. Consult your nearest Ingersoll-Rand Authorized Service Center.
  • Page 3: Exploded View And Parts List

    EXPLODED VIEW AND PARTS LIST SERIES SRV125F STARTER RELAY VALVE (Dwg. TP2184) When ordering, use applicable part number Item Part Description Part Number Item Part Description Part Number Valve Housing ....SRV125F-40 End Plug .
  • Page 4: Optional Equipment

    OPTIONAL EQUIPMENT (Dwg. TP2212) When ordering, use applicable part number Item Part Description Part Number Item Part Description Part Number Solenoid and Mounting Hardware - Position 1 Pilot Port Hardware - Position 2 Solenoid 90° Elbow with Push to Lock ..EL90-4M4DOT 12 Volt, Pioneer Connections .
  • Page 5: Pre-Installation

    Ensure that the air line is suitably aligned and supported to vented Control Valve to the small tapped hole in the top of avoid strained joints. the Starter Relay Valve. Use SMB-441 Ingersoll-Rand Seal- Do not over tighten the air line connections. ant on the male thread.
  • Page 6: Maintenance

    MAINTENANCE Installation of the Tune Up Kit WARNING Disassembly of the Starter Relay Valve Bleed off the air pressure. Always wear eye protection when lubricating or performing Clamp the Starter Relay Valve in a vise with the Retaining maintenance on the Starter Relay Valve. Always bleed off the Ring (12) facing up.
  • Page 7 NOTES P7648 Edition 1...
  • Page 8: Service Centers

    Fax: (416) 213-4510 India Chile Phone: (0120) 477-1001/2/3/4 Europe/ Middle East/ Africa Ingersoll-Rand Chile Fax: (0120) 477-1005 Ingersoll-Rand Tool & Hoist Division Nueva Tajamar 555, 15th fl. Zone du Chene Sorcier Las Condes, Santiago Japan BP 62 Chile Ingersoll-Rand Japan,Ltd.

Table of Contents