1. Manuals
  2. Brands
  3. Nexen Manuals
  4. Industrial Equipment
  5. AIR CHAMP Burke E. Porter 5H50P
  6. User manual

Nexen AIR CHAMP Burke E. Porter 5H50P User Manual

Multiposition tooth clutch
Hide thumbs Also See for AIR CHAMP Burke E. Porter 5H50P:
Table of Contents

Advertisement

Quick Links

Download this manual
Burke E. Porter 5H50P
Multiposition Tooth Clutch
(i)
FORM NO. L-20222-G-0501

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the AIR CHAMP Burke E. Porter 5H50P and is the answer not in the manual?

Questions and answers

Related Manuals for Nexen AIR CHAMP Burke E. Porter 5H50P

Summary of Contents for Nexen AIR CHAMP Burke E. Porter 5H50P

  • Page 1 Burke E. Porter 5H50P Multiposition Tooth Clutch FORM NO. L-20222-G-0501...
  • Page 2 In accordance with Nexen’s established policy of constant product improvement, the specifications contained in this manual are subject to change without notice. Technical data listed in this manual are based on the latest information available at the time of printing and are also subject to change without notice.

  • Page 3: Table Of Contents

    TABLE OF CONTENTS Introduction ---------------------------------------------------------------------------------------------------------------------------------------- 1 Installation ---------------------------------------------------------------------------------------------------------------------------------------- 2 Anti-rotation Clip and Engagement Indicator Switch ----------------------------------------------------------------------------- 2 Air Connections --------------------------------------------------------------------------------------------------------------------------------- 3 Engagement Indicator Switch Adjustment -------------------------------------------------------------------------------------------- 3 Lubrication ----------------------------------------------------------------------------------------------------------------------------------------- 3 Troubleshooting---------------------------------------------------------------------------------------------------------------------------------- 4 Parts Replacement ----------------------------------------------------------------------------------------------------------------------------- 5 Replacement Parts ----------------------------------------------------------------------------------------------------------------------------- 8 Parts List ------------------------------------------------------------------------------------------------------------------------------------------- 9 Warranties --------------------------------------------------------------------------------------------------------------------------------------- 10 (iii)

  • Page 4: Introduction

    Accordingly, anyone who uses a procedure that is not recommended by Nexen must first satisfy themselves that neither their safety or the safety of the product will be jeopardized by the service method selected.

  • Page 5: Installation

    The 5H50P Tooth Clutch has a drive flange with two bearings, a pilot diameter, and tapped holes for mounting Nexen's Flexible Coupling. 5H50P NOTE: Nexen recommends using a red anaerobic thread locking compound on Pilot Mounting Bolts. The 5H50P mounts on a full shaft using a full length Key.

  • Page 6: Air Connections

    NOTE: Pneumatically actuated devices require clean, pressure regulated, and lubricated air for maximum performance and long life. The most effective and economical way to lubricate Nexen 5H50P is with an Air Line Lubricator, which injects oil into the pressurized air, forcing an oil mist into the air chamber.

  • Page 7: Troubleshooting

    LUBRICATOR DRIP RATE SETTINGS NOTE: These settings are for Nexen supplied lubricators. If you are not using a Nexen lubricator, calibration must replicate the following procedure. 5. Connect the air line to the unit. 1. Close and disconnect the air line from the unit.

  • Page 8: Parts Replacement

    PARTS REPLACEMENT DISASSEMBLY Drive Special attention should be exercised when Flange working with retaining rings. Always wear safety goggles when working with spring or tension loaded fasteners or devices. 1. Remove Retaining Ring (Item 11) (See Figure 4). (Item 1) NOTE: If a press is not available, use a bearing puller to remove Drive Flange from the Hub.
  • Page 9 DRIVE FLANGE BALL BEARINGS (Item 9) Special attention should be exercised when working with retaining rings. Always wear safety goggles when working with spring or tension loaded fasteners or devices. 1. Remove Retaining Ring (Item 10) (See Figure 7). 2. Push the Ball Bearings (Item 9) out of Drive Flange (Item 15) (See Figure 7).
  • Page 10 PISTON BALL BEARING (Item 9) Special attention should be exercised when working with retaining rings. Always wear safety goggles when working with spring or tension loaded fasteners or devices. 1. Remove Retaining Ring (Item 11) (See Figure 9). 2. Press Hub (Item 1) out of Piston (Item 3) and Ball Bearing (Item 9) (See Figure 9).

  • Page 11: Replacement Parts

    Hub, Piston, Cylinder Assembly FIGURE 12 REPLACEMENT PARTS The item or balloon number for all Nexen products is used When ordering replacement parts, specify model for part identification on all product parts lists, product designation, item number, part description, and quantity.

  • Page 12: Parts List

    PARTS LIST 5H50P ASSEMBLY FIGURE 13 ITEM DESCRIPTION ITEM DESCRIPTION Retaining Ring Cylinder Retaining Ring Piston O-ring Seal Drive Ring O-ring Seal Backing Plate Fitting (Not Shown) Compression Springs Drive Flange Ball Bearing Seal, Back-up Ring Ball Bearing Seal, Back-up Ring Denotes Repair Kit items (Product No.

  • Page 13: Warranties

    Exclusive Remedy The exclusive remedy of the Buyer for any breach of the warranties set out above will be, at the sole discretion of Nexen, a repair or replacement with new, serviceably used or reconditioned Product, or issuance of credit in the amount of the purchase price paid to Nexen by the Buyer for the Products.

Table of Contents