Related Manuals for Daikin FTXM09WVJU9
Summary of Contents for Daikin FTXM09WVJU9
- Page 1 DAIKIN ROOM AIR CONDITIONER INSTALLATION MANUAL R32 Split Series Installation manual Manuel d’installation Manual de instalación MODELS FTXM09WVJU9 FTXM12WVJU9 FTXM18WVJU9 FTXM24WVJU9...
-
Page 2: Table Of Contents
Contents Safety Considerations ........1 Refrigerant Piping Work ........ 10 Accessories ............3 1. Flaring the pipe end ........... 10 2. Refrigerant piping............10 Choosing an Installation Site ......3 Installation Tips ..........11 1. Indoor unit ..............3 1. Removing and installing the front panel..... 11 2. - Page 3 Plastic parts may deteriorate and fall off or result in water specified by Daikin are used, fire or explosion may occur. leakage. • When installing or relocating the air conditioner, do not let...
-
Page 4: Accessories
Accessories Mounting plate Mounting plate Titanium apatite deodorizing fixing screw filter M4 × 1” (M4 × 25mm) Wireless remote Remote controller Remote controller controller holder holder fixing screw M3 × 13/16” (M3 × 20mm) Dry battery AAA. Indoor unit fixing Screw cover LR03 (alkaline) screw... -
Page 5: Indoor Unit Installation Diagram
Indoor Unit Installation Diagram CAUTION • Do not hit or violently push the INTELLIGENT EYE sensor. This can lead to damage and malfunction. • Do not place large objects near the INTELLIGENT EYE sensor. Also keep heating units or humidifiers outside the sensor’s detection area. -
Page 6: Indoor Unit Installation
Indoor Unit Installation Installing the mounting plate The mounting plate should be installed on a wall which can support the weight of the indoor unit. 1)Temporarily secure the mounting plate to the wall, make sure that the plate is completely level, and mark the drilling points on the wall. -
Page 7: Drilling A Wall Hole And Installing Wall Embedded Pipe
Drilling a wall hole and installing wall embedded pipe WARNING For metal frame or metal board walls, be sure to use a wall embedded pipe and wall hole cover in the feed-through hole to prevent possible heat, electric shock, or fire. •... - Page 8 Indoor Unit Installation 3-2. Left-side, left-back, or left-bottom piping How to switch around the drain plug and drain hose 1) Remove the fixing screw and 3) Switch around the drain hose and drain plug. Insert drain hose securely pull out the drain hose. and fix in place with fixing screw.
-
Page 9: Wiring
Wiring Refer to the installation manual for the outdoor unit also. WARNING • Do not use tapped wires, extension cords, or starburst connections, as they may cause overheating, electric shock, or fire. • Do not use locally purchased electrical parts inside the product. (Do not branch the power for the drain pump, etc., from the terminal block.) Doing so may cause electric shock or fire. -
Page 10: Drain Piping
Indoor Unit Installation Drain piping 1) Connect the drain hose, as described on the right. Make a downward slope • Avoid placing the end of the drain hose in a drainage location that could cause bad odors or corrosive gas to flow backward into the outlet. •... -
Page 11: Refrigerant Piping Work
Refrigerant Piping Work WARNING • Do not apply mineral oil on flared part. • Prevent mineral oil from getting into the system as this would reduce the service life of the units. • Never use piping which has been used for previous installations. Only use parts which are delivered with this unit. •... -
Page 12: Installation Tips
Installation Tips Removing and installing the front panel • Removal method 1) Place your fingers in the indentations on the main unit (one each on the left and right sides), and open the front panel until it stops. 2) While pushing the left side front panel shaft outward, push up the front panel and remove it. -
Page 13: When Connecting To An Ha System
When connecting to an HA system For this procedure, accessories which are sold separately are needed. (wired remote controller, central remote controller, etc.) • In case there is a work space on the right side of the indoor unit, the procedure can be done while fixing the electrical wiring box. -
Page 14: Trial Operation And Testing
Trial Operation and Testing Trial operation and testing • Trial operation should be carried out in either COOL or HEAT operation. 1-1. Measure the supply voltage and make sure that it is within the specified range. 1-2. In COOL operation, select the lowest programmable temperature; in HEAT operation, select the highest programmable temperature. - Page 15 MEMO...
- Page 16 The two-dimensional bar code is a manufacturing code. 3P686877-1A M21B545A (2205) HT...