Advertisement
5.2.1.
raise the eye shield up, and away from the stone.
5.2.2.
loosen and pull the tool rest out as far as possible, but, do not remove it (fig 6).
5.2.3.
Remove the screws from the side of the wheel cover and remove the cover (fig 6).
5.2.4.
Hold grinding stone firmly. To protect your hands use cloth or wear gloves. Unscrew retaining nut (fig.7.1)
Note: The nut on the right side of the grinder has standard right hand thread (undo anti-clockwise).
the left side nut has a left hand thread and must be loosened by turning clockwise. it may be necessary
to strike the wrench sharply in the loosening direction with the heel of your hand to loosen the nut.
5.2.5.
Remove grinding stone washer (fig 7.2), blotter (3),stone (4), 2nd blotter (5), washer (6) from main
spindle (7).
5.2.6.
carefully inspect the new stone before installing to ensure there are no fissures, chips, or cracks.
warning! dO nOT uSe a damaged STOne.
‰
5.2.7.
inspect the blotters, if they are damaged replace them. the grinder must never be used without stone
blotters, should you not have any available when you need to replace them, cut out a piece of suitable
cardboard the same shape for temporary use only.
5.2.8.
Install the new stone by reversing steps above. Ensure washers (2 & 6) are installed with the flange
on the outside, (i.e. the concave side against the blotter).
5.2.9.
Hold stone steady and secure locking nut. dO nOT over tighten as this may crack the stone.
5.2.10.
replace stone cover, re-adjust tool rest to a maximum of 2mm from stone face and tighten securely.
note: You do not require a certificate to change a wire wheel. Assembly is the same as with a stone.
6. OperaTiOn
6.1.
pre use inspection.
note: use the same clearance and alignment information if your model has a wire brush.
warning! INSPECT THE GRINDER BEFORE OPERATING THE MACHINE. ENSURE THE GRINDER IS UNPLUGGED FROM
‰
THE MAINS POWER BEFORE COMMENCING THE INSPECTION.
6.1.1.
check the tool rests are securely fixed and set at a maximum of 2mm from the grinding stone.
6.1.2.
check that eye shields are in good condition, are secure and that you can see through them clearly.
6.1.3.
turn the grinding stones by hand and check for any damage. check they do not touch the tool rests and are correctly aligned.
if any of the above checks fail, replace, repair, or adjust as necessary before starting the grinder.
6.2.
Stone use.
depending on the model, grinders are supplied with one or two aluminous oxide stones. stones have two grades, fine are preferred
for hard materials and a coarse stones for soft materials.
When grinding, should surface of the stone become "loaded" (coated with particles of the material being ground) it is probably the
wrong grade of stone for the job.
important reminder: Grinding stones must only be assembled by a person holding a grinding wheel certificate.
6.3.
using the grinder.
warning! Before commencing work, ensure you have read, understood, and apply the section 1. Safety Instructions Plug grinder into
‰
the mains power supply. Place the eyeshield in its appropriate safety location.
switch the grinder on, and bring the workpiece slowly into contact with the spinning stone, or wire wheel.
When you have completed your task, unplug the grinder from the mains power supply, and clean the machine ready for next use.
7. mainTainance
warning! ensure the grinder is unplugged from the mains power supply before performing any maintenance or service.
‰
7.1.
As the grinding stone wears, adjust the position of the tool rests. the rest must be at a maximum of 2mm from the stone surface.
7.2.
regularly remove the grinding stone covers and clean out any dust and dirt.
7.3.
the machine motor and bearing are sealed units and require no regular maintenance. should you require assistance, contact your
local sealey service agent.
7.4.
for information relating to the handling and maintenance of grinding stones refer to section 5.
parts support is available for this product. To obtain a parts listing and/or diagram,
please log on to www.sealey.co.uk, email sales@sealey.co.uk or telephone 01284 757500.
environmental protection
recycle unwanted materials instead of disposing of them as waste. All tools, accessories and packaging should be
sorted, taken to a recycling centre and disposed of in a manner which is compatible with the environment.
When the product becomes completely unserviceable and requires disposal, drain off any fluids (if applicable)
into approved containers and dispose of the product and the fluids according to local regulations.
weee regulations
dispose of this product at the end of its working life in compliance with the eu directive on
Waste Electrical and Electronic Equipment (WEEE). When the product is no longer required, it must be disposed
of in an environmentally protective way. contact your local solid waste authority for recycling information.
NOTE: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice.
impOrTanT: no liability is accepted for incorrect use of this product.
warranTy: Guarantee is 12 months from purchase date, proof of which will be required for any claim.
© Jack sealey limited
sole uK distributor, sealey Group.
Kempson Way, Suffolk Business Park,
Bury st. edmunds, suffolk.
iP32 7AR
Original Language Version
01284 757500
01284 703534
BG150XL/96.V2 | Issue 1 20/10/16
fig.6
fig.7
section 5.
www.sealey.co.uk
sales@sealey.co.uk
Advertisement
