Sealey BG150XD/99.V3 Instructions

Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these
instructions, and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
Refer to Wear eye
instructions protection
1. SAFETY
1.1. Electrical Safety
WARNING! It is the user's responsibility to check the following:
‰
Check all electrical equipment and appliances to ensure that they are safe before using. Inspect power supply leads, plugs and
all electrical connections for wear and damage. Sealey recommend that an RCD (Residual Current Device) is used with all electrical
products. You may obtain an RCD by contacting your local Sealey dealer.
If used in the course of business duties, it must be maintained in a safe condition and routinely PAT (Portable Appliance Test) tested.
Electrical safety information, it is important that the following information is read and understood.
Ensure that the insulation on all cables and on the appliance is safe before connecting it to the power supply.
9
regularly inspect power supply cables and plugs for wear or damage and check all connections to ensure that they are secure.
9
Ensure that the voltage rating on the appliance suits the power supply to be used and that the plug is fitted with the correct fuse - see
9
fuse rating in these instructions.
DO NOT pull or carry the appliance by the power cable.
8
DO NOT pull the plug from the socket by the cable.
8
DO NOT use worn or damaged cables, plugs or connectors. Ensure that any faulty item is repaired or replaced immediately by a
8
qualified electrician.
This product is fitted with a BS1363/A 13 Amp 3 pin plug.
9
If the cable or plug is damaged during use, switch the electricity supply and remove from use.
Ensure that repairs are carried out by a qualified electrician.
Replace a damaged plug with a BS1363/A 13 Amp 3 pin plug. If in doubt contact a qualified electrician.
a) Connect the GREEN/YELLOW earth wire to the earth terminal 'E'.
b) Connect the BROWN live wire to the live terminal 'L'.
c) Connect the BLUE neutral wire to the neutral terminal 'N'.
Ensure that the cable outer sheath extends inside the cable restraint and that the restraint is tight.
Sealey recommend that repairs are carried out by a qualified electrician.
1.2. General Safety
WARNING! Disconnect the grinder from the mains power, and ensure the grinding wheels are at a
‰
standstill before attempting to change
Note: With the exception of "Abrasive Wheels Regulations"' safety instructions will also apply to use of a
wire brush on appropriate models.
Maintain the grinder in good condition and check moving parts alignment regularly.
9
Replace or repair damaged parts. Use recommended parts only. Non authorised parts may be dangerous and will invalidate the
9
warranty.
▲ DANGER! DO NOT use a damaged stone as it is dangerous and may cause damage or serious personal injury.
WARNING! Only persons qualified under the "Abrasive Wheels Regulations" and holding a current grinding wheel certificate are to
‰
change or dress grinding stones. Unplug grinder from mains power and refer to chapter 4 "Grinding Stones" for details.
WARNING! Keep all guards and holding screws in place, tight and in good working order. Check regularly for damaged parts.
‰
A guard or any other part that is damaged should be repaired or replaced before tool is used. The safety guard is a mandatory fitting
where grinder is used in premises covered by the Health & Safety at Work Act.
Locate grinder in an adequate working area for its function, keep area clean, tidy and free from unrelated materials. Ensure adequate
9
lighting.
Before each use check grinding wheel for condition. If worn or damaged replace immediately.
9
WARNING! Always wear approved eye or face protection when operating the grinder.
‰
Use breathing protection in accordance with COSHH regulations if fumes or dust pose a hazard. Wear ear defenders and gloves if
9
necessary.
Keep hands and body clear of the work piece when operating the grinder.
9
Maintain correct balance and footing. Ensure the floor is not slippery and wear non slip shoes.
9
Remove ill fitting clothing. Remove ties, watches, rings, and other loose jewellery, and contain and/ or tie back long hair.
9
Keep children and unauthorised persons away from the working area.
9
DO NOT force the grinder to achieve a task it was not designed to perform.
8
DO NOT operate the grinder if any parts are damaged or missing as this may cause failure or possible personal injury.
8
© Jack Sealey Limited
BENCH GRINDER Ø150MM 450W/230V
HEAVY-DUTY
BG150XD/99.V3
MODEL NO:
Wear a mask Wear ear
protection
accessories, service or perform any maintenance.
Original Language Version
Recommended fuse rating
3 Amp
BG150XD/99.V3 Issue 2(2) 10/09/20