Chapter 1 Getting Started Before you begin installing your new AMD FirePro™ W7000 graphics card (P/N: 102- C418xx-xx), please make sure you have the proper system requirements and have completed the required preinstallation tasks as outlined in this chapter. 1.1 System Requirements The following are minimum requirements for installing a single AMD FirePro™...
If needed, remove any old graphics accelerator(s). Install the new graphic accelerator. Reassemble and connect your computer system and display(s). Start the computer system and install the AMD FirePro™ drivers and configuration software. Restart the computer system. 2.2 Installing a PCI Express Graphics Card Please read all installation instructions completely before you begin.
Page 10
Make sure all internal cables are clear of the slot. 6. Align your AMD FirePro graphics card with the PCIe slot and press it in firmly until the card is fully seated. You may need to hold open the PCIe card slot- locking mechanism with your finger when you seat the card.
Your monitor will be running in a basic (VGA) video mode. Higher refresh rates are not available at this stage of the installation. Once you have installed the AMD FirePro drivers and software, you can use the Windows®Display Properties dialog to adjust your video settings and configure multiple monitors.
6 Hardware and Software Installation 2.3.2 AMD Automatic Application Detection and Configuration AMD FirePro drivers offer automatic application detection and configuration, which enables the graphics driver to automatically detect an application when it starts and configure the graphics driver settings for optimal performance.
4 DisplayPort 1.2 Connection 3.1.2 Stereoscopic Connection The following figure shows the stereoscopic port that connects your AMD FirePro™ W7000 graphics card to stereographic glasses. The bracket can be attached if needed, or left off so that the graphics card covers only one PCI slot in the computer's case.
8 Display Configuration Figure 3–2 AMD FirePro™ W7000 Stereoscopic Connection 1 Stereoscopic Connection The following figure shows where the cable from the sterescopic bracket connects to your AMD FirePro™ W7000 graphics card. Figure 3–3 Sterescopic Cable Connection 3.2 Connecting Displays The following table lists the different ways you can connect displays to your card: AMD FirePro™...
• DisplayPort connection with DisplayPort-to-VGA adapter display Note: Adapters mentioned here may not be included with your AMD FirePro product. Once displays are connected to the graphics card, you can control how they are currently configured as well as how Windows® desktops appear on the displays using the Control Center software application.
Use the following procedure to attach a display using an adapter. 1. Turn off your computer and monitor. 2. Plug the adapter into the connection from the baseplate of your AMD FirePro product and tighten the thumbscrews (if there are any).
CPU for improved power savings or system performance. You can also use the performance tools in the application to monitor and manage clock speed and memory use for your graphics card to ensure that your AMD product is configured and running as efficiently as possible.
Chapter 5 AMD CrossFire™ Pro Technology Note: These features are only available for AMD FirePro™ W7000 graphics cards with AMD CrossFire™ Pro connections. 5.1 AMD CrossFire™ Pro Overview AMD CrossFire Pro is a multi-GPU (graphics processing unit) high performance graphics platform. It enables two graphics processors installed in a single computer to work together to improve system performance.
Page 22
5. Align the new workstation card in the primary PCIe slot next to the existing graphics card and press firmly until the card is fully seated. Figure 5–1 AMD FirePro™ Card Installation Note: You may need to hold open the PCIe card slot-locking mechanism with your finger when you seat the card.
Page 23
AMD CrossFire™ Pro Technology 17 8. Connect the two AMD FirePro™ workstation cards using the AMD CrossFire Pro bridge interconnect. Figure 5–2 AMD CrossFire™ Pro Interconnect Installation Newly installed AMD FirePro card AMD CrossFire Pro Interconnect 9. Make sure that no cables are interfering with anything inside the computer (for example, a cooling fan) and then replace the computer cover.
This chapter provides notices, troubleshooting tips, and customer care, warranty, and standards-compliance information. 6.1 Product Features This chapter describes some of the special features that are associated with the AMD FirePro™ W7000 product and are available through the Control Center software application.
Framelock is a synchronization method that uses output locking and also synchronizes 3D rendering on multiple GPUs. Framelock and genlock for AMD FirePro workstation cards is provided by the ATI FirePro S400 synchronization module. Each synchronization module supports genlock and framelock for up to four GPUs per PC.
Page 28
The house sync signal connects to the BNC connection on the AMD FirePro™ W7000. The following diagram shows a single PC with four GPUs connected to an AMD FirePro™ W7000 synchronization module genlocked to an external signal generator.
Page 29
The following series of diagrams shows a variety of possible framelocking configurations. The following image shows a single PC with four GPUs connected to an AMD FirePro™ W7000 synchronization module framelocked with an internal reference clock signal. Figure 6–3 Single PC with Four GPUs Framelocked The following is an advanced framelock setup using two PCs with four GPUs each connected to an AMD FirePro™...
Page 30
Figure 6–4 Two PCs with Four GPUs Each Framelocked This diagram shows an advanced framelock and genlock setup using four PCs with four GPUs each; each computer is connected to an AMD FirePro™ W7000 synchronization module synchronized with an external signal generator.
Windows documentation. 6.2 Workstation Card Troubleshooting The following troubleshooting tips may help if you experience problems. More troubleshooting information can be found using the knowledgebase on the AMD Web site at http://support.amd.com/. AMD FirePro™ W7000 Graphics Accelerator...
If your system has built-in graphics capabilities, make sure that you uninstall • the associated driver to prevent conflicts with AMD graphics drivers. Make sure that you selected the appropriate monitor when you installed your enhanced driver.
Memory Addresses: Video RAM: A000-BFFF, Video ROM: C000-C7FF • You cannot change the addresses of your AMD FirePro card. In case of an address conflict, try to modify the I/O address of the add-on card that causes the conflict. To support the special graphics processor on the AMD FirePro card, the system BIOS should automatically assign a system interrupt to the slot where the card is installed.
6.3.2 Disclaimer AMD Customer Care will work to resolve your issue and help you to get your product up and running. If your issue is not resolved, our technicians will determine whether the difficulty you are experiencing is the result of the product, whether your product contains a defect, and whether your product should be returned to AMD for warranty service.
No warranties for this product, expressed or implied, shall extend to any person who purchases the product in a used condition. The liability of AMD in respect of any defective product will be limited to the repair or replacement of such product. AMD may use new or equivalent-to-new replacement parts.
China RoHS standards. For information on China RoHS, EU RoHS, or EU REACH compliance, please refer to Product Environmental Compliance on the AMD Web site. 6.5.10 Waste Electrical and Electronic Equipment (WEEE) Directive Compliance (European Union) This product was manufactured by Advanced Micro Devices, Inc.