Bosch 0 601 B27 000 Original Instructions Manual page 39

– For softer damping, loosen the two set screws (48) using
the hex key (4 mm) (30)
– or
– tighten the two set screws (48) for harder damping.
Clamping the Workpiece (see figure G)
To ensure maximum safety while working, the workpiece
must always be firmly clamped.
Do not saw workpieces that are too small to clamp firmly.
– Press the workpiece firmly against the fence (8).
– Insert the supplied screw clamp (19) into one of the holes
(49) intended for this purpose.
– Firmly clamp the workpiece by turning the threaded rod
(50).
Setting mitre and bevel angles
To ensure precise cuts, the basic settings of the power tool
must be checked and adjusted as necessary after intensive
use.
Experience and suitable special tools are required for this.
A Bosch after-sales service point will handle this work
quickly and reliably.
Always tighten the locking knob (11) firmly before
u
sawing. Otherwise the saw blade can become wedged in
the workpiece.
Adjusting the horizontal mitre angle
Setting Standard Mitre Angles (see figure H)
For quick and precise setting of commonly used mitre
angles, detents (14) are provided on the saw table:
Leftward
0°
45°; 31.6°; 22.5°; 15°
– Loosen the locking knob (11) if it is tightened.
– Pull the lever (12) and rotate the saw table (33) left or
right to the required detent.
– Release the lever again. The lever must be felt to engage
in the detent.
– Retighten the locking knob (11).
Setting any mitre angle (see figure I)
The mitre angle can be set between 52° (left side) and 60°
(right side).
– Loosen the locking knob (11) if it is tightened.
– Pull the lever (12) and at the same time push the mitre
detent override (10) downward at the front.
This locks the lever (12) and the saw table can move
freely.
– Turn the saw table (33) left or right by the locking knob
until the angle indicator (51) shows the required mitre
angle.
– Retighten the locking knob (11).
– To loosen the lever (12) again (for setting standard mitre
angles), pull the lever upwards.
The mitre detent override (10) springs back into its ori-
Bosch Power Tools
Adjusting vertical mitre angles
The bevel angle can be set between 47° (left side) and 47°
(right side).
For quick and precise setting of frequently used bevel
angles, stops have been provided for the angles 0°, 22.5°,
45° and 47°.
Setting the left-hand bevel angle range (45° to 0°)
– Pull the left-hand adjustable fence (7) all the way out.
– Loosen the clamping handle (13).
– Use the handle (3) to swivel the glide arm (23) to the left
– Hold the glide arm (23) in this position and retighten the
Setting the Right-hand Bevel Angle Range (0° to 45°)
(see figure J)
– Pull the right-hand adjustable fence (7) all the way out.
– Loosen the clamping handle (13).
– Use the handle (3) to tilt the glide arm (23) slightly to the
Rightward
– Use the handle (3) to swivel the glide arm (23) to the
15°; 22.5°; 31.6°; 45°; 60°
– Hold the glide arm (23) in this position and retighten the
Setting the Standard 0° bevel angle
– Swivel the glide arm (23) from the right to the 0° position.
Setting the entire bevel angle range (–47° to +47°)
– Pull both adjustable fences (7) all the way out.
– Loosen the clamping handle (13).
– Use the handle (3) to tilt the glide arm (23) slightly to the
ginal position and the lever (12) can click back into the
detents (14).
until the angle indicator (28) shows the required bevel
angle.
clamping handle (13).
The clamping force of the clamping handle must hold the
glide arm securely in place at any bevel angle.
left from the 0° position and turn the rotary knob (32) un-
til the required bevel angle range is shown.
right until the angle indicator (21) shows the required
bevel angle.
clamping handle (13).
The clamping force of the clamping handle must hold the
glide arm securely in place at any bevel angle.
To enable the standard 0° bevel angle to be reset
easily, the rotary knob (32) engages in the left-
hand bevel angle range.
left from the 0° position and turn the rotary knob (32) un-
til the required bevel angle range is shown.
English | 39
1 609 92A 6SR | (09.07.2021)