Related Manuals for HIKOKI NR 3665DA
Summary of Contents for HIKOKI NR 3665DA
- Page 1 NR 3665DA “STRAP-TITE™” ONLY FOR USE WITH PRE-PUNCHED HOLED METAL CONNECTOR Handling instructions...
- Page 2 NR3665DA (NN) (2XC) ― BSL36A18 ― UC18YSL3 ― ―...
- Page 6 Do not loosen these screws...
- Page 8 BSL36A18 UC18YSL3 (14.4 V–18 V) 329897 371896...
-
Page 9: General Power Tool Safety Warnings
power source and/or battery pack, picking up or GENERAL POWER TOOL SAFETY carrying the tool. WARNINGS Carrying power tools with your fi nger on the switch or energising power tools that have the switch on WARNING invites accidents. Read all safety warnings and all instructions. d) Remove any adjusting key or wrench before Failure to follow the warnings and instructions may result in turning the power tool on. -
Page 10: Additional Safety Warnings
c) When battery pack is not in use, keep it away 3. Be careful of ignition and explosions. from other metal objects, like paper clips, coins, Since sparks may fl y during nailing, it is dangerous to use keys, nails, screws or other small metal objects, this tool near lacquer, paint, benzine, thinner, gasoline, that can make a connection from one terminal to gas, adhesives and similar infl... - Page 11 12. Do not carelessly place your fi nger on the trigger. 21. Remove battery from nailer when: Do not place your fi nger on the trigger except when loading nails. actually nailing. If you carry this tool or hand it to 22.
-
Page 12: Caution On Lithium-Ion Battery
39. When transporting the nailer, it should be stored 9. Keep away from fi re immediately when leakage or foul in the provided case or a sturdy container such odor are detected. as a packing box to avoid accidental damage. In 10. - Page 13 The battery remaining power is nearly empty. Lock lever Recharge the battery as soon as possible. Battery indicator:1 LED (Red) blink Handle Contact HiKOKI for inspection. Probe Battery indicator: 2 LEDs blink in Orange, after 10 seconds, automatically turn off Nail support (B) Power switch.
-
Page 14: Specifications
346 mm × 325 mm × 127 mm Height × Length × Width 2. Battery Charger Model UC18YSL3 Charging voltage DC 14.4–18 V Weight 0.6 kg NOTE Due to HiKOKI’s continuing program of research and development, the specifi cations herein are subject to change without prior notice. -
Page 15: Nail Selection
NAIL SELECTION WARNING Be sure to use only the genuine HiKOKI nails for the NR3665DA. The use of any other nails can result in tool malfunction and/or nail breakdown, leading to serious injuries. Choose a suitable nail from Fig. Nails which are not shown in Fig. can not be driven with this tool. - Page 16 Table 1 Indications of the charge indicator lamp Lights for 0.5 seconds. Does not light for Before Blinks 0.5 seconds. (off for 0.5 seconds) Plugged into power source charging (RED) Lights for 0.5 seconds. Does not light for Blinks 1 second. (off for 1 second) Battery capacity at less than 50% (BLUE) While...
-
Page 17: Before Use
Power switch more than 1 second, then power order. indicator goes off . If abnormal operation occurs, stop using the Nailer and Under the condition of “Power switch ON”, functions contact a HiKOKI authorized service center immediately. below are active. - Page 18 (1) REMOVE ALL NAILS AND BATTERY FROM NAILER. Hold the trigger back and depress the push lever against the workpiece again. □ ALL SCREWS MUST BE TIGHTENED. □ THE NAILER MUST NOT OPERATE. □ THE PUSH LEVER AND TRIGGER MUST MOVE SMOOTHLY with pulling back the feeder knob.
- Page 19 Removing the nails: WARNING Pull the feeder knob backward. (See Fig. 10) ○ Confi rm that the nailing operation indicator is lit in blue. Return the feeder knob forward quietly while pushing the ○ To avoid double fi ring or accidental fi ring due to recoil. nail feeder (A).
-
Page 20: Maintenance And Inspection
M5 bolt. the battery is disassembled and modifi ed (such as NOTE disassembly and replacement of cells or other internal In case of frequent jam, contact a HiKOKI authorized parts). service center. MAINTENANCE AND INSPECTION NOTE CAUTION Due to HiKOKI’s continuing program of research and... -
Page 21: Troubleshooting
Nailer operation. TROUBLESHOOTING Use the inspections in the table below if the tool does not operate normally. If this does not remedy the problem, consult your dealer or the HiKOKI Authorized Service Center. PROBLEM CHECK METHOD CORRECTION Power switch doesn’t turn on. - Page 22 The charger’s vents are blocked, causing Avoid blocking the vents. its internal components to overheat. The cooling fan is not running. Contact a HiKOKI Authorized Service Center for repairs. Charging of a USB device The charger was plugged into an electrical This is not a malfunction.
- Page 24 Shinagawa Intercity Tower A, 15-1, Konan 2-chome, Minato-ku, Tokyo, Japan Code No. C99270411 G Printed in China...
Need help?
Do you have a question about the NR 3665DA and is the answer not in the manual?
Questions and answers