Hunter Crestfield Installation Manual
Hide thumbs
Also See for Crestfield:
- Installation manual (13 pages) ,
- Installation manual (13 pages) ,
- Installation manual (13 pages)
Related Manuals for Hunter Crestfield
Summary of Contents for Hunter Crestfield
- Page 1 Prep Connect Complete Crestfield Installation Manual Model: 52534 Matte Silver 52535 Fresh White 52536 Noble Bronze Fan weight ±2 lbs: 24.0 lbs (10.9 kg) ©2023 Hunter Fan Co. M4011-01 r032923...
- Page 2 Congratulations on purchasing your new Hunter ceiling fan! ® The ceiling fan you purchased will provide comfort and performance in your home or office for many years. This instruction manual contains complete instructions for installing and operating your fan. We are proud of our work and appreciate the opportunity to supply you with the best ceiling fan available anywhere in the world.
-
Page 3: Tools Needed For Installation
Tools Needed for Installation Box Outlet Mount Building Structure Mount 9/64" Box Contents Hardware Included Parts Included Canopy Mount Canopy Fan Body Wood Screw x2 Small Flat Head Jumper Screwdriver Harness Light Kit Washer x2 Snap-on Blades Glass Cover Light Bulb Pull Chains... -
Page 4: Before Beginning Installation
Before Beginning Installation Standard Mount This installation is for flat ceilings using the short pre-installed Turn Power OFF, breaker and light switch. downrod ceiling fans. WARNING IMPORTANT The longest accessory downrod that can be used with To avoid possible electrical shock, before installing your fan, fans is 12-inches. -
Page 5: Installation
Installation – Canopy Mount and Terminal Wiring 1a 1a Building Structure Mount Building Structure Mount Prep • You must be able to secure the fan to building structure or fan-rated outlet box. • You have two options for installation. Pick which one works best for your location. - Page 6 Installation – Canopy Mount and Terminal Wiring (continued) Single Switch Wiring Single Switch Wiring Connect wiring from ceiling to terminal block (on side of canopy mount) and tighten using flathead screwdriver (included). For single switch wiring an additional jumper harness component will be Green, Green Yellow Stripe, or Bare (grounding) Green, Green Yellow Stripe, or Bare (grounding) needed which is seen in step 2d.
- Page 7 Prep Installation – Fan Body, Wiring Harness, Canopy Cover, and Blades IMPORTANT Note: For single switch wiring an additional jumper harness component will be needed. Take the jumper harness (H) from the accessories bag. Connect the female end to the hanging bracket connector. Connect Connect the male end of the jumper harness to the ceiling fan connector.
- Page 8 Installation – Light Kit Complete Notch Remove the cardboard plug guard before proceeding! 3c 3c Connect the plugs from the fan and light fixture. Make sure to line up the colored markings on the Raise the light kit to the bottom of the fan. Align the connectors.
- Page 9 Installation – Glass Cover Screw Bulb Glass 3e 3e To install the glass, first loosen the thumb Install a bulb into each of the sockets. When screws. Raise the glass to the light fixture. necessary, replace with bulbs of same Tighten all thumbscrews securely.
- Page 10 Turn Power ON, breaker and main switch. Reversing the Fan Reverse Switch Updraft (clockwise rotation) creates a more indirect airflow. Updraft airflow is great for moving warm air downward. Downdraft (counterclockwise rotation) creates a direct breeze and maximum cooling effect. Ceiling fans work in two directions: downdraft (counterclockwise rotation) and updraft (clockwise rotation).
-
Page 11: Troubleshooting
Hunter instructions, accidental damage caused by the fan owner or related parties, Please do not ship your fan or any fan parts to Hunter. Delivery will be refused. modifications to the fan, improper or incorrectly performed maintenance or repair,... - Page 12 Using a Different Size Downrod If you need a different downrod length follow these steps: Cross Pin Retention Spring In order to change the length of Disengage retention spring by downrod, the pivot assembly needs to be pulling away from rod. Then disengaged.
Need help?
Do you have a question about the Crestfield and is the answer not in the manual?
Questions and answers
Where is serial number