Related Manuals for Yard force GM R40A
Summary of Contents for Yard force GM R40A
- Page 1 GM R40A XSZ40B PETROL LAWNMOWER Original Instructions READ & UNDERSTAND INSTRUCTION MANUAL Save all warnings and instructions for future reference.
- Page 2 Read this manual carefully prior to assembling and operating the petrol lawnmower. It is dangerous to operate this product without being familiar with these instructions. Keep this manual in a safe place and have it ready for future reference.
-
Page 4: Table Of Contents
INTENDED USE GM R40A Original Instructions This lawnmower has been designed for cutting grass. The machine is to be used only for its prescribed purpose, any other use is deemed to be a case of misuse. Please note that our equipment has not been designed for use in commercial, trade or CONTENT industrial applications. -
Page 5: General Safety Warnings
GENERAL SAFETY WARNINGS PRODUCT SAFETY WARNINGS thrown by the machine. machine if you observe any damaged components. 3. Petrol is highly flammable; store fuel in containers NOTE: This lawn mower complies with the Noise specifically designed for this purpose. Emission Directive 2000/14/EC. Noise Emission in the a). - Page 6 PRODUCT SAFETY WARNINGS PRODUCT SAFETY WARNINGS 8. Do not mow excessively steep slopes. 19. Stop the engine and disconnect the spark plug wire, 9. Use extreme caution when reversing or pulling the and make sure that all moving parts have come to a lawn mower towards you.
-
Page 7: Symbols
SYMBOLS SYMBOLS Safety symbols Please read all of the safety and operating The purpose of safety symbols is to attract your attention instructions carefully before using this machine. to possible dangers. The safety symbols and the Read the instruction manual before operating. explanations with them require your careful attention and full understanding. -
Page 8: Technical Data
SYMBOLS TECHNICAL DATA The blade continues to rotate for a period after Model GM R40A Engine type Single cylinder 4-stroke the machine is switched off. Do not touch the Engine displacement 127.1 cm blade until all the machine components have... -
Page 9: Description Of Product
DESCRIPTION OF PRODUCT INSTALLATION Parts description (Fig. A) WARNING: Always take care when removing the packaging, to prevent damage to you or to the lawn mower. This item requires a two-person lift to remove it from the Upper handle packaging. Make sure that you have sufficient space to put the lawn mower down. Rope guide Keep your feet apart so that you have a stable position;... -
Page 10: Operation
OPERATION OPERATION Filling with engine oil (Fig. I) Setting the cutting height (Fig. K) IMPORTANT! The following procedures and adjustments must be performed WARNING! before the engine is started. Do not attempt to make any of these adjustments The blade can cause serious injury. Before adjusting the mower height, stop the while the engine is running. -
Page 11: Maintenance And Storage
OPERATION MAINTENANCE AND STORAGE Using the drive function (Fig. N) Storing the lawn mower for short periods This unit is self-propelled. Start the mower as previously mentioned. After mowing, please follow the actions below prior to placing the lawn mower in storage: Use one hand to hold the blade control bar firtmly pressed against the main handle. - Page 12 MAINTENANCE AND STORAGE MAINTENANCE AND STORAGE Start the engine and allow it to run briefly. After every use After 12 hours use After 24 hours use After 36 hours use Stop the engine, wait one minute and check the oil level. Top up if necessary. Cleaning Clean Clean...
-
Page 13: Troubleshooting
United Kingdom Declare that the product: Fault Possible cause Solution Description: Petrol lawnmower Model No. XSZ40B/ GM R40A Loud while - Screws are loose - Check screws running, Function: Cutting grass - Blade fasteners are loose - Check blade fasteners... -
Page 14: Declaration Of Conformity
59 bis Rue du Mûrier 37540 Saint Cyr Sur Loire France Declare that the product: Description: Petrol lawnmower Model No. XSZ40B/ GM R40A Function: Cutting grass Complies with the essential health and safety requirements of the following directives: Machinery Directive 2006/42/EC...