Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for BELLISSIMO HNTB64GWS
Summary of Contents for BELLISSIMO HNTB64GWS
- Page 1 Instructions for Use and Installation 60cm stainless steel gas cooktop HNTB64GWS...
-
Page 2: Table Of Contents
Contents For your safety Installation ......... 3 During use . -
Page 3: For Your Safety
For Your Safety These instructions have been drawn up for your safety and that of others. You are therefore requested to read them carefully before installing and using the appliance. Keep this instruction manual for future reference as necessary. If the appliance is sold or moved, make sure that the manual is handed over to the new user. -
Page 4: During Use
For Your Safety DURING USE This product is designed to cook foods inside private · homes and for non-commercial purposes. It should not be used for any other purpose. · After using the appliance, make sure that all controls are in 'CLOSED' or 'OFF' position. -
Page 5: Safety Of Children And The Infirm
For Your Safety Safety of children and the infirm This appliance must only be used by adults. Make sure that children do not touch the controls or play with the appliance. The exposed parts of this appliance heat up during cooking and remain hot for some time even after it is switched off. -
Page 6: Use And Care
Use and Care Description of the hob 1. Hob 2. Wok burner 3. Semi-rapid burner 4. Auxiliary burner 5. Control knobs 6. Pan Support LH 7. Pan Support RH Note: Model shown may not be identical to the hotplate you have purchased. The symbols on the control knobs mean the following: No gas flow or 'Off' Maximum gas flow or 'high' flame and lighting position... -
Page 7: To Light The Burners
Use and Care To light the burners To light the burner, press the control knob down completely and hold down before rotating anti-clockwise to the ‘High’ Flame position. The ignition device is integrated into the control knob and is automatically activated by pushing down on the control knob. After lighting the flame, keep the knob pressed for about 5 seconds: this time is necessary to heat up the thermocouple (D on page 6) and activate the safety valve, which would otherwise cut... -
Page 8: For Correct Use Of The Hob
Use and Care For correct use of the hob For lower gas consumption and better efficiency, use only flat- bottomed pans of dimensions suitable for the burners, as shown in the table below. Also, as soon as a liquid comes to the boil take care to turn the flame down to a level that will just keep it boiling. -
Page 9: Cleaning And Maintenance
Use and Care Cleaning and maintenance Before cleaning, disconnect the appliance from the electrical mains, make sure all burners are 'off' and allow the hotplate to cool down. General cleaning Wash enameled parts with lukewarm water and detergent: do not use abrasive products which might damage them. - Page 10 Use and Care Ignition plug Automatic burner ignition is provided by a ceramic 'plug' and a metal electrode (Ignition Candle - E on page 6). Periodically clean these parts of the hob thoroughly. In addition, to avoid ignition difficulties, check that the cavities in the burner are not obstructed. To remove deposits from the burner cavities, remove the burner caps.
-
Page 11: Abnormal Operation
Use and Care Routine maintenance Have the condition and efficiency of the gas pipe and the pressure regulator (if installed) checked periodically. If anomalies are found, do not repair components but have the faulty component replaced. To ensure good performance and safety, the gas regulator taps must be greased periodically. -
Page 12: Installation
Installation Technical data Gas intake connection 1/2" BSP · · Electricity supply 220-240V AC (50Hz) Natural Gas Burner Type 1.0 kPa 2.75 kPa Nominal Gas Injector Nominal Gas Injector (mm) Consumption (mm) Consumption 0.90 3.9 MJ/h 0.53 3.3 MJ/h Auxiliary 6.9 MJ/h 0.70 6.0 MJ/h... -
Page 13: Building Into Kitchen Benches
Installation Building into kitchen benches These hobs are designed for installation in kitchen benches. When installed into a corner, the walls or panels above the benchtop must be at least 155mm away from the edge of the hob to ensure adequate air circulation to the burners. -
Page 14: Installation Cutout Drawing
Installation Installation Cutout Drawing HNTB64GWS Gas Inlet Point... -
Page 15: Connection To The Gas Supply
Installation Connection to the gas supply There are two ways to make the connection to the main gas line: A. The hotplate can be connected with rigid pipe as specified in AS/NZS 5601 table 3.1. B. The hotplate can be connected with a Flexible Hose, which complies with AS/NZS 1869 (AGA Approved), 10mm ID, class B or D, no more than 1.2m long and in accordance with AS/NZS5601. -
Page 16: Electrical Connection
Installation Electrical connection This appliance is designed to operate on a power supply voltage of 220-240V, single phase and is fitted with a 10A, 3 pin plug. Before making the connection, make sure that: 1) The electrical system is able to withstand the load of the appliance (see data label). -
Page 17: Before Leaving
Installation Before leaving When the installation is complete, always check for gas leaks using a soapy solution. Never use a flame to make this check. Ignite all burners on high flame to ensure correct operation of gas valves, burners and ignition. Turn gas taps to low flame position and observe each burner to ensure they ignite completely at all ports and that the flame is stable. -
Page 18: Wiring Diagrams
Installation Wiring diagrams... -
Page 19: Gas Conversion (Ng To Ulpg)
Gas Conversion (NG to ULPG) If the required gas conversion kit is not supplied with your appliance, contact Technika. Gas Conversion shall only be undertaken by authorised persons. The NG to U-LPG conversion kit contains... - Test Point Assembly LPG Gas Type label - Auxiliary Jet Ø0.53mm - Semi-Rapid Jet Ø0.70mm - Rapid Jet Ø0.90mm... -
Page 20: Gas Conversion (Ulpg To Ng)
Gas Conversion (ULPG to NG) If the required gas conversion kit is not supplied with your appliance, contact Technika. Gas Conversion shall only be undertaken by authorised persons. The ULPG to NG conversion kit contains... - NG Regulator - NG Gas Type label - Auxiliary Jet Ø090mm - Semi-Rapid Jet Ø1.18mm... -
Page 21: Troubleshooting
Installation Troubleshooting Please complete the troubleshooting before calling for service as user error or installation faults WILL NOT be covered under warranty. General troubleshooting For all issues with the burners, please check the following items first: 1. DO NOT cover any part of the cooktop with foil. As well as being very dangerous, this can cause issues with burners not igniting or burning incorrectly. - Page 22 Installation Cooktop issues Burner clicks but will not light: Complete the general troubleshooting on page 21 first. When lighting the burner, be sure to turn the knob to the high flame symbol at the 9 o'clock position (see instructions on page 6) Remove the burner cap.
- Page 23 Installation Cooktop issues (continued) Ignitor keeps clicking: It is most likely some moisture has entered the ignition switches under the knobs. This may be from spillage or when cleaning with liquids. Turn off the cooktop at the power point and allow 24-48 hours for it to dry out before switching it back on.
- Page 24 READ THE INSTRUCTION BOOKLET BEFORE INSTALLING AND USING THE APPLIANCE. The manufacturer will not be responsible for any damage to property or to persons caused by incorrect installation or improper use of the appliance. The manufacturer is not responsible for any inaccuracies, due to printing or transcription errors, contained in this handout.