Advertisement
Quick Links
FieldPoint
FP-20 xx FieldPoint Quick Start Guide
What You Need
• FP-20 xx LabVIEW RT controller
to Get Set Up
• 35 mm DIN rail
• Two DIN rail locks (included)
• Terminal base(s)
• I/O module(s)
• 11–30 VDC power supply
Install the Network Module
1
Mount the module on a DIN rail.
A. Unlock rail clip.
© National Instruments Corporation
TM
• Accessories: Ethernet cable,
flathead screwdriver
• PC running Windows
• National Instruments FieldPoint
Software CD
• LabVIEW RT
1
FP-20xx Quick Start Guide
Advertisement
Related Manuals for National Instruments FELDPoint FP-2000
Summary of Contents for National Instruments FELDPoint FP-2000
- Page 1 • 35 mm DIN rail flathead screwdriver • Two DIN rail locks (included) • PC running Windows • Terminal base(s) • National Instruments FieldPoint • I/O module(s) Software CD • 11–30 VDC power supply • LabVIEW RT Install the Network Module Mount the module on a DIN rail.
- Page 2 NOTE Do not use spliced DIN rails. Use only a single DIN rail. B. Hook lip on back of module onto top of DIN rail, press down, and snap into place. C. Slide module into position and lock rail clip. FP-20xx Quick Start Guide ni.com...
- Page 3 CAUTION Terminal bases must be connected to the network module before applying power to the module. Do not connect or disconnect terminal bases while power is applied to the network module. A. Unlock rail clip. B. Press base onto rail. © National Instruments Corporation FP-20xx Quick Start Guide...
- Page 4 C. Slide base into position and lock rail clip. Be careful not to bend any pins. D. Repeat for each terminal base, up to nine for each network module in most cases. You can use one or two extender cables (which you can order separately) if the FieldPoint bank is too long for the available space.
-
Page 5: Install The I/O Module(S)
Connect the FP-20 xx to an Ethernet network by connecting the RJ-45 Straight-Through Ethernet port of the UTP Cable FP-20 xx to an Ethernet hub using a standard Straight-Through Category 5 Ethernet cable. UTP Cable © National Instruments Corporation FP-20xx Quick Start Guide... - Page 6 Do not use a cable longer than 100 m. If you are using a 100 Mbps Ethernet, National Instruments recommends using a Category 5 shielded twisted-pair cable. If you need to build your own cable, refer to the FP-20xx User Manual specifications section for cabling details.
- Page 7 FP-AI-100 FP-AO-200 FP-RLY-420 FP-TC-120 Power supply connected to 15 16 V and COM terminals Shades of gray indicate 31 32 C C 17 18 different voltage potentials. CAUTION Cascading power defeats isolation. © National Instruments Corporation FP-20xx Quick Start Guide...
- Page 8 Connect to Field Devices Use the operating instructions for each I/O module to help you connect field devices. Power Up the FieldPoint System CAUTION Terminal bases must be connected to the FP-20 xx before power is applied to the FP-20 xx. Make sure the RESET DIP switch is not on.
- Page 9 B. Close all other applications. C. Insert the National Instruments FieldPoint Software CD into the CD-ROM drive of your computer. D. Follow the onscreen instructions to complete the installation. NOTE If the setup does not launch automatically, select Start»Run from Windows, enter d:\setup, where d is the letter of the CD-ROM drive, and select OK.
-
Page 10: Specifications
Specifications Network Network interface ....10BaseT and 100BaseTX Ethernet Compatibility....IEEE802.3 Communication rates . - Page 11 • EN 61010-1, IEC 61010-1 • UL 3121-1, UL 61010C-1 • CAN/CSA C22.2 No. 1010.1 NOTE For UL and other safety certifications, refer to the product label or to ni.com. © National Instruments Corporation FP-20xx Quick Start Guide...
- Page 12 Electromagnetic Compatibility CE, C-Tick and FCC Part 15 (Class A) Compliant Emissions ..... . EN 55011 Class A at 10 m FCC Part 15A above 1 GHz Immunity .
-
Page 13: Mechanical Dimensions
Mechanical Dimensions 107.19 mm (4.22 in.) 109.5 mm (4.31 in.) 91.44 mm (3.60 in.) © National Instruments Corporation FP-20xx Quick Start Guide... - Page 14 Thailand 662 992 7519, United Kingdom 44 0 1635 523545 CVI™, FieldPoint™, LabVIEW™, Measurement Studio™, National Instruments™, NI™ and ni.com™ are trademarks of National Instruments Corporation. Product and company names mentioned herein are trademarks or trade names of their respective companies.