Related Manuals for Monmouth Scientific CT675
Summary of Contents for Monmouth Scientific CT675
- Page 1 Operating & Maintenance Manual Clean Tent CT675/CT750/CT1700 www.monmouthscientific.co.uk...
-
Page 2: Table Of Contents
Safety ..............................4 Safety & Disclaimer Notice ......................... 4 Processes ............................. 5 Installation .............................. 6 CT675, CT750 and CT1700 ........................6 Groundsheet ............................7 HEPA fan filter unit (FFU) frame ......................8 Tent top section ..........................9 Suspended ceiling ..........................13 Frame structure .......................... -
Page 3: Introduction
ISSUE A Thank you On behalf of everyone at Monmouth Scientific Ltd, thank you for choosing to purchase your Clean Tent from us. We are committed to providing you with the highest level of customer satisfaction possible. If for any reason you are unhappy with your Clean Tent or have any questions or comments regarding your Clean Tent, or our company we would love to hear from you. -
Page 4: Safety
All personnel must be suitably trained in the use of any equipment used during the installation of this Clean tent. It is the customer’s responsibility to ensure the safety of all colleagues and personnel carrying out this task. Monmouth Scientific Limited does not accept responsibility for any injury or damage howsoever caused. -
Page 5: Processes
ISSUE A All Monmouth Scientific systems have been designed to assure operator safety providing the following rules are observed and proper usage is made of the equipment. Refer to ALL appropriate instructions and manuals BEFORE using the equipment. DO NOT... -
Page 6: Installation
Installation CT675, CT750 and CT1700 This section covers instruction for installation by others i.e., non-Monmouth Scientific staff. Check that the shipping list and parts delivered are identified and present. Any discrepancies should be notified to Monmouth Scientific or its agents as soon as possible. -
Page 7: Groundsheet
‘Partition’ feet aligned with the edge of the groundsheet. • Clean the groundsheet with IPA alcohol solution or similar. Figure 1 View our ceiling clip training video at: https://cleanenvironments.co.uk/videos/clean-tent-training-video/ Monmouth Scientific Limited Units 5 & 6 Kilnside, East Quay, Bridgwater TA6 4DB Phone: +44 (0)1278 555173 Email: sales@monmouthscientific.co.uk... -
Page 8: Hepa Fan Filter Unit (Ffu) Frame
FFU and line up with the holes on the rear of the HEPA. Ensure the pre-filter is fitted into the intake flange. Power up and check that the fan is working then disconnect. Monmouth Scientific Limited Units 5 & 6 Kilnside, East Quay, Bridgwater TA6 4DB... -
Page 9: Tent Top Section
FFU Skirt onto the FFU. Then simply fold back the top and sides so that the Velcro connects. Apply pressure evenly all the way around to ensure a firm connection is made. Monmouth Scientific Limited Units 5 & 6 Kilnside, East... - Page 10 ISSUE A Figure 2 Figure 3 Monmouth Scientific Limited Units 5 & 6 Kilnside, East Quay, Bridgwater TA6 4DB Phone: +44 (0)1278 555173 Email: sales@monmouthscientific.co.uk...
- Page 11 Qty of suspension points provided on Tent Load per suspension point (All points used) 0.5kg 0.66kg 0.75kg Total load 12kg 15kg FFU fan speed control Monmouth Scientific Limited Units 5 & 6 Kilnside, East Quay, Bridgwater TA6 4DB Phone: +44 (0)1278 555173 Email: sales@monmouthscientific.co.uk...
- Page 12 ISSUE A Clean Tent inflating Monmouth Scientific Limited Units 5 & 6 Kilnside, East Quay, Bridgwater TA6 4DB Phone: +44 (0)1278 555173 Email: sales@monmouthscientific.co.uk...
-
Page 13: Suspended Ceiling
Tie the Bungee off at a corner loop and then thread through alternating ceiling anchors and tent loops. Tie off allowing for some tension in the bungee. Monmouth Scientific Limited Units 5 & 6 Kilnside, East Quay, Bridgwater TA6 4DB... -
Page 14: Frame Structure
Pass the cord between the tent loops and over the frame structure until you have completed the two sides and front of the Clean Tent. Tie off the bungee on the final loop. Tents utilising a frame structure Monmouth Scientific Limited Units 5 & 6 Kilnside, East Quay, Bridgwater TA6 4DB... -
Page 15: Frame Structure Assembly
Loosen the union enough to allow it to slide into the leg. Ensure the sections are aligned and tighten the union. Monmouth Scientific Limited Units 5 & 6 Kilnside, East Quay, Bridgwater TA6 4DB Phone: +44 (0)1278 555173 Email: sales@monmouthscientific.co.uk... - Page 16 Be aware the larger frame structure used with the CT1700 has longer cross braces to increase support for the longer side bars (not shown here) Monmouth Scientific Limited Units 5 & 6 Kilnside, East Quay, Bridgwater TA6 4DB Phone: +44 (0)1278 555173 Email: sales@monmouthscientific.co.uk...
-
Page 17: Erecting The Frame Structure
Take care to ensure all these connections are correctly made before carefully laying the frame down to rest. Pay attention to ensure the corner brace T-nuts are fully rotated and secure. Monmouth Scientific Limited Units 5 & 6 Kilnside, East Quay, Bridgwater TA6 4DB... - Page 18 Take care to ensure all these connections are correctly aligned and pay close attention to ensure the corner brace T-nuts are fully rotated and secure. Monmouth Scientific Limited Units 5 & 6 Kilnside, East Quay, Bridgwater TA6 4DB...
-
Page 19: Using Clean Tent
WARNING It is possible to go from outside to the grey area if the wrong zipper is opened from outside, similarly from white to black on exit. All users should be aware that this possibly breaks protocol and should be avoided. Monmouth Scientific Limited Units 5 & 6 Kilnside, East Quay, Bridgwater TA6 4DB... -
Page 20: Getting Equipment Into The Work Cabin
Air conditioning Ensure that the unit air intake is from inside the cabin and place the unit in the cleanroom with the heat dump tube outside to ambient via the zip joint. If the user needs to retro fit a through wall gland, please get in touch with your Monmouth Scientific or your agent. -
Page 21: Air Supply And Calibration
1Pa.using this method. Since the pressure delivered is proportional to the airflow for a given volume, we can use this as a guide to the face velocity of the HEPA. Monmouth Scientific Limited Units 5 & 6 Kilnside, East... -
Page 22: Placing Equipment & Workstation Location Within The Cleanroom
Particulate levels Personnel clothing, traffic in and out of the tent, pre-filter changes, and frequent wipe downs, all make the difference to the quality of the environment. Monmouth Scientific Limited Units 5 & 6 Kilnside, East Quay, Bridgwater TA6 4DB... -
Page 23: Maintenance
The FFU is a self-contained fan filter module, designed for use in turbulent mixing and laminar airflow cleanroom areas. See separate MAC10 installation, operation, & maintenance manual. Monmouth Scientific Limited Units 5 & 6 Kilnside, East Quay, Bridgwater TA6 4DB... -
Page 24: Housekeeping
All cleaning must be done with the HEPA turned on at maximum velocity and the exhaust vents open for maximum throughput. Monmouth Scientific Limited Units 5 & 6 Kilnside, East Quay, Bridgwater TA6 4DB Phone: +44 (0)1278 555173 Email: sales@monmouthscientific.co.uk... -
Page 25: Questions And Support
Telephone: UK 01278 458090 International +44 1278 458090 Office Hours: 8.45am to 5.00pm Email: info@monmouthscientific.co.uk Alternatively, please contact your sales agent. Monmouth Scientific Limited Units 5 & 6 Kilnside, East Quay, Bridgwater TA6 4DB Phone: +44 (0)1278 555173 Email: sales@monmouthscientific.co.uk... - Page 26 Monmouth Scientific Limited UK Headquarters Units 5 & 6 Kilnside, East Quay, Bridgwater, Somerset, TA6 4DB. +44(0)1278 458090 www.monmouthscientific.co.uk info@monmouthscientific.co.uk B r i t i s h D e s i g n & Manufacture...
Need help?
Do you have a question about the CT675 and is the answer not in the manual?
Questions and answers